Search Documents

By Christopher R. Harris

"Considerations are presented for developing and implementing self-hardening slurry mix designs to be utilized in barrier seepage walls. Slag-cement-cement-bentonite (SCCB) slurries are the primary focus, with some comparisons referenced to the more traditional Portland-based cement-bentonite (CB) slurries. Field and laboratory mixing methods are reviewed, including 1) single sack – single mixer method; 2) bentonite slurry mixer – cementitious addition mixer method; 3) bentonite mixer – grout mixer – CB blending mixer method. Major phenomena associated with the dynamics of barrier wall excavation, such as loss of water from the in-trench slurry and consolidation of in-trench slurry are discussed. Other topics touched upon include sand content effects, fluidizers utilized, and chemical contaminants. The role of higher bentonite to water ratio is reviewed, with demonstration of improvement of filtration properties, and an increase of water retention of the final consolidated product.IntroductionSelf-hardening slurry has been utilized to construct barrier seepage walls for many decades. This is essentially a single-step slurry excavation and backfill process whereby the trench-supporting fluid gains strength over a short period during installation and maintains or develops low hydraulic conductivity. The resulting curing slurry becomes the actual barrier wall as the resultant cement-augmented clay slurry now fulfills the dual purpose of both temporary trench stabilization and final cured-in-place product. This eliminates the requirement and expense of subsequent backfill/slurry displacement operations required in traditional barrier wall installations.Self-hardening slurries have been fabricated using a number of various clays, most commonly sodium bentonite, calcium bentonite, attapulgite, and sepiolite. Perhaps due to plentiful high quality sodium bentonite deposits found domestically, the proven excavation stabilization properties imparted from sodium bentonite slurries, sodium bentonites are typically specified for formulating self-hardening slurries in the US. Cementitious materials utilized most commonly are Portland cement and slag (ground blast furnace slag or GBFS). For the purposes of this discussion, self-hardening slurry having a cementitious of Portland will be referred to as CB. Those having cementitious material of GBFS replacing Portland (partially or wholly) will be referred to as SCCB."

Jan 1, 2016

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Osvaldo Valdez, Matteo Bertoni, Aem Ragy

The East St. Louis Deep Cutoff Wall project is located in the area of East St. Louis, Illinois, across the Mississippi River from the city of St. Louis, Missouri, along the left descending bank of the river. The project is a fundamental part of the U.S. Army Corps of Engineers' (USACE) effort to rehabilitate and secure the aging East St. Louis levee system that provides flood protection to approxi- mately 250,000 residents and more than $4.5 billion in economic value. The project was devised and de- signed by USACE as a cutoff wall to be installed in the Metro East Sanitary District levee segment, one of the levee segments that form the East St. Louis system. The contract for the construc- tion of the cutoff wall was awarded in November 2019 to Bauer Foundation, the American subsidiary of the Bauer Group.

Sep 1, 2023

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By Andreas Massarsch

Information Technology, IT, is rapidly affecting all aspects of private life and how professional activities are conducted. Probably the most important development is the Internet, which makes it possible to exchange information independently of time and geographic location. While traditional communication is based on limited availability to information, the basis of the new Information Technology age is abundance and unlimited access. IT has evolved into a powerful resource and new applications are being developed and introduced almost daily. IT influences every aspect of our private life as well as our business environment. If properly used, IT can become an important resource for planning and implementing construction projects more efficiently, at lower cost and with higher quality. Interactive Web Platforms are already being used for group collaboration on a global scale. As these can be used without programming knowledge and are user-friendly, Web Platforms make cooperation more efficient and stimulate members to actively participate. Another application of growing interest are Internet Platforms and electronic publishing, which can provide technical and other information in different formats and much cheaper than conventional books or proceedings.

Jan 1, 2002

By Mehih Demirkan, Kevin Tehansky

Located about an hour drive south from Washington, D.C., the Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new Governor Harry W. Nice Memorial/Senator Thomas "Mac" Middleton Bridge, which takes U.S. 301 over the Potomac River, spanning 1.9 mi (3 km) from Maryland to Virginia. The new bridge aimed to improve capacity, safety and access of the roadway and was planned as a four-lane span with deep foundations that would be constructed fewer than 150 ft (45 m) north of the existing alignment of the more than 80-year-old bridge. The new Harry Nice Bridge opened in the fall of 2022 with a design life of more than 100 years, servicing 12 ft (4 m) wide lanes with 2 ft (0.6m) shoulders, doubling capacity, enhancing emergency response, upgrading maintenance and inspection activity access, and featuring lane sharing for cyclists.

Apr 1, 2023

By Nathan Iverson, Allie Brady

Located on rolling bluffs on the Zumbro River's south fork in Southeast Minnesota, Rochester is the state's third largest city and is the home and birthplace of the renowned Mayo Clinic, a nonprofit academic medical center focused on integrated health care, education and research. Mayo Clinic employs more than 4,500 physicians and scientists with another 58,000 administrative and allied health staff across three major campuses: Rochester, Minnesota; Jacksonville, Florida; and Phoenix/Scottsdale, Arizona. Originally developed as a stagecoach stop, Rochester has become a national destination for medical care, drawing more than two million visitors annually to Mayo's Minnesota location. Since January 2022, Veit & Company has been working on the construction of the Mayo 1st Ave Tunnel, which comprises three tunnels (pedestrian, utility and services), and the RMC Loading Dock projects in Rochester. These adjacent projects are on the Mayo Clinic's ever-expanding campus and represent its continued dedication to improvement and advancement as a leading medical service provider in the industry.

Jan 1, 2023

By Chen Zhiquan

Author has exhaustively researched into soft ground through construction of a large open caisson on soft ground (muck) which weighs more than 4, 000 tons. To avoid any contingency during construction, we precompressed muck stratum with a sand cushion and consolidated it with sand piles before construction of the caisson. We made borehole surveyings and soil tests many times before and after ground treatment. Following the tracks of changes of the caisson at all stages of precasting, we surveyed a large number of data. On the basis of analysis of the data we changed the original construction plan of precasting in four stages and sinking in three stages into that of precasting in three stages and sinking in one stage. Through the practice of the whole caisson construction the author has advanced new theory of kinematic law for soil particles and the change's law for strength of muck during precompression of sand cushion and consolidation of sand piles.

Jan 1, 1991

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Don C. Warrington

This paper describes a new wave equation analysis program called ZWAVE, which is a program specifically for external combustion hammers. The program is de-scribed in detail, the discussion dealing with topics concerning the program such as 1) the numerical method the program uses to integrate the wave equation, which is different from most other wave equation programs; 2) the modelling process of both cushioned and cushionless hammers; 3) the automated generation of mass and spring values for both hammer and pile; 4) the method of dealing with plastic cushions; 5) the use of a recently developed model for computing shaft resistance during driving; 6) the computation and generation of values based on basic soil properties such as shear modulus, Poisson's Ratio and soil density; 7) the completely interactive method of feeding data to the program; 8) the method used to compute the anticipated rebound and the energy used to plastically deform the soil; and 9) the format of the inter-active input of the program and the program's output. Sample problems for the program, along with comparison of the program results with data gathered in the field, are presented.

Jan 1, 1988

By Tom George

"INTRODUCTIONNo. 1 Queens Rd was an existing 10-storey office building founded on large pad footings. This project involved the construction of a 6-level, 15m (50-ft.) deep basement excavated immediately adjacent to the existing building and also beneath the existing footprint of the Southern end of the building. The total perimeter of the new basement was to be approximately 200m (656 ft.) all with a retained height of 15m (50 ft.). It was also proposed to add a further 5 storeys to the building. Approximately 18 of the existing columns supporting the 10-storey building were to have the applied column load diverted from the existing foundations at ground level onto the new piles or basement raft 15m (50 ft.) below.The geotechnical profile consisted of fill for the top 1.5m predominately comprising of clayey sand with a high gravel content from 1.5m to 9m (5 to 30 ft.), a medium dense to dense clayey sand and then below was a sandy clay extending to 15m (50 ft.) ranging from stiff to very stiff. From 15m on completely to extremely weathered siltstone was encountered. The groundwater was measured at 9.5m (31 ft.) below the natural ground surface.DESIGN BRIEFThe existing building columns were founded on large pad foundations up to 4.4m (14.5 ft.) square, founded on the dense clayey sand. These pads would require temporary support to enable the excavation to proceed beneath them. Upon completion of the excavation under the pads new columns were to be constructed joining into the existing columns to transfer the load onto the new raft slab, 15m (50 ft.) below. The existing 10 floors were to be refurbished. It was planned to undertake all the temporary support and transferring of loads while the structure above was only able to provide a dead load. It was decided that any movement of the building would have minimum impact on a skeleton structure. During the temporary support of the columns, movements due to construction activities had to be monitored to understand any potential stresses in the structure above.The original design required beams to be installed under the pads and supported at either end by temporary piles that were to be founded below the level of the proposed excavation. (Refer to sketch 1). Wagstaff Piling considered that this methodology had difficulties in construction at all stages and did not provide facility for transfer of the load without significant movement of the structure above. Wagstaff Piling revised the design to attach beams to the columns above the pads using shear collars. (Refer to sketch 2). These beams supported on the temporary piles could then be jacked upwards to remove loads off the pads. This would enable removal of the pads with minimal movement of the 10-storey building above. (Refer to photo 1 and back cover photo)."

Jan 1, 2005

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By Kimberly Martin

The EFFC/DFI Carbon Calculator provides the deep foundations industry the opportunity to be a leader when it comes to carbon reduction. This tool was created 10 years ago in an extensive effort by the European Federation of Foundation Contractors (EFFC), DFI, member organizations and Carbone 4, a consultant with ex- perience in life cycle assessment. The tool was born out of the fact that governments and clients were asking for embodied carbon information for foundation systems, and that in- dividual companies were building their own calculators to meet these requests. To help all member organ- izations achieve compliance, and to have a sector-specific tool that is certified to the prevailing standards, EFFC and DFI agreed to partner to create the carbon calculator, which is: Excel based and, therefore, easy to learn and use Updated on a regular schedule Certified to ISO 14067, GHG Protocol and PAS 2050 Free and available for anyone to use Even though this tool is free and easy to use, most projects in the industry do not have a carbon calculation performed. The case to use the calculator is more obvious for members in places like Europe where there are stricter reporting standards and government work can be driven by sustainability over cost. In North America this is not the case, yet. Without directives from clients and governments, what can compel the industry to start regularly using this tool and care about the carbon emissions of projects during design and construction?

Nov 1, 2022

By Hitoshi Ogura, Koichi Kobayashi, Sadao Yabuuchi

"In Japan, most pile foundations using pre-cast concrete piles are installed by the bored pre-cast piling method, wherein pre-cast piles are installed in holes that have been excavated beforehand and filled with cement milk (term used for cement water slurry in Japan). The bored pre-cast piling method with enlarged base, in which the portion near the toe is enlarged during boring operation, is widely used because of the cost benefits and the increased vertical bearing capacity that this method offers.The EX MEGATOP method, further developed as an improved bored pre-cast piling method with enlarged base, is reported here. The features of this method are: (1) High vertical bearing capacity; (2) High degree of freedom in design; (3) Excellent workability; and (4) Friendly to the environment. In particular, high vertical bearing capacity can be obtained using nodular piles and by enlarging the area at the pile toe and shaft. This method can gave a vertical bearing capacity coefficient at the toe of a=430, more than twice the corresponding value of a = 200 of a conventional bored pre-cast pile. Moreover, the shaft resistance can be several times larger than that of a conventional bored pre-cast pile. This report gives an overview of the EX MEGATOP method, evaluation of vertical bearing capacity, and examples of application of the method.1.lntroductionMost pile foundations in Japan are installed by the bored pre-cast piling method, that is, in holes that have been excavated beforehand and filled with cement water slurry, referred to as 'cement milk'. The ""bored pre-cast piling method with enlarged base"" is frequently used. In this method an enlarged excavation is used near the pile toe to increase the vertical bearing capacity.The EX MEGATOP method is a variation of the bored pre-cast piling method. Its features include the use of nodular piles and a long, enlarged excavation. The vertical bearing capacity of the EX MEGATOP method is described in this report."

Jan 1, 2005

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By H. Cheng

The Bohai Oil Company has applied all together 11 jack-up oil drilling rigs (movable platforms) (1) which can be classified in terms of their forms of foundations into two types: the integ­ral mat and the column legged, as demonstrated in figure 1. Figure 1 a) indicates the entire structure of the sunk cushion type, i.e. the one with a box-like sunk cushion serving as its foundation by directly sitting on the sea bed. The length, width and height of the outer sides for the sunk cushion stand at 45.8 x 38.0 x 3.3m ( for Rig Bohai No.2 ) and 50.6 x 33.2 x 4.88m ( for Rig Bohai No.6 ), the relative areas of theirs being 1475m2 and 2008m2 respectively and both bigger than the plane areas of the rigs. With a view to realize a convenient drainage of mud while sinking, two holes of 14 x 14m and 32 x 18m in size are constructed in the center part of the sunk cushion. When work sets off, the underside of the sunk cushion operates as a foundation, the sunk cushion being connected to the platform by hull columns which transmit the load of the platform down­wards to the sunk cushion that passes it further onto the subgrade. [ ] Column legs for rigs may also be grouped into two categories considering their features: columns with and without boots. The bodies of boot columns are made up of trusses, whose bottoms, are boot-shaped with a big diameter. The diameter of boot columns of the rigs applied by the Bohai Oil Company shows bigger and it may reach 12 or 18m. In the boot columns, the transmission of the platform's weight into soil is done by the underside areas of boots. While in the case of the vertical columns, which are of cylinder columns of steel with sealed bottom ends shaped inverted arch, the entire drilling platform is supported by the carrying force delivered by the bottoms of these steel cylinders and the frictional force rendered by their outside walls. Such a type of columns is featured by a small diameter, 3m in general. Figure 2 exhibits the schematic diagram of sections regarding the two types of column legs.

Jan 1, 2010