Search Documents

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By Andrea Lisjak Bradley

Clay shales are currently being assessed as possible host rock formations for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this thesis was to develop and validate a mechanically-based model of the deformation and failure process of a clay shale, namely Opalinus Clay (OPA), with particular focus on the influence of anisotropy on the short-term response of circular tunnels. To achieve this goal, a hybrid continuum-discontinuum numerical approach was developed in combination with new field measurements from the Mont Terri underground research laboratory. The response of OPA during the excavation of a full-scale emplacement (FE) test tunnel was characterized by geodetic monitoring of wall displacements, radial extensometers and longitudinal inclinometers. The deformation measurements indicated strong directionality induced by the combined effect of in-situ stress field and bedding planes striking parallel to the tunnel axis, with the most severe deformation occurring in the direction approximately perpendicular to the material layering. Computer simulations were conducted using a newly-extended combined finite-discrete element method (FEM/DEM), a numerical technique which allows the explicit simulation of brittle fracturing and associated seismicity. The numerical experimentation firstly focused on the laboratory-scale analysis of failure processes (e.g., acoustic activity) in brittle rocks, and on the role of strength and modulus anisotropy in the failure behaviour of OPA in tension and compression. The fracturing behaviour of unsupported circular excavations in laminated rock masses was then analyzed under different in-situ stress conditions. Lastly, the proposed modelling methodology was applied to the aforementioned FE tunnel to obtain unique insights into the EDZ formation process around emplacement tunnels for nuclear waste. The calibrated numerical model suggested delamination along bedding planes and subsequent extensional fracturing as key mechanisms of the damage process potentially leading to buckling and spalling phenomena. Overall, the research findings are already having a direct impact on the preliminary design process of an underground repository for nuclear waste in Switzerland.

Jan 1, 2015

By Balmer Neilly

In these days of arrested prosperity, when patience is tried and the future but dimly outlined, Canada's gold mining industry stands out as a beacon light shedding its rays of hope and confidence and demonstrating that there is still one product unaffected by Customs barriers and eagerly sought by all the people of the world. Some other forms of industry have hesitated and side-stepped. Some have cried for help, and in spite of public assistance, generously extended, they are still unable to demonstrate definitely their ability to resume the onward march. But gold mining has never hesitated. As an industry, it has bad an unique experience. When prices are high and conditions are generally referred to as prosperous, this industry is adversely affected. The cost of production goes up; profits are diminished; public sympathy is lacking; and, thrown upon its own resources, the industry tightens up its belt and throws its whole energy into an effort to improve operating conditions, and offset high prices by increased efficiency. When, in due course, depression follows inflation and prices ebb, the gold miner, through necessity, finds himself physically and mentally prepared to meet the situation.

Jan 1, 1932

By A. E. Soregaroli, H. D. Meade

"The Keystone porphyry molybdenum deposit, located in southcentral British Columbia, is hosted by intrusive rocks of the Cretaceous Mount Lytton batholith and the early Tertiary Keystone quartz diorite stock. The molybdenite mineralization is associated with rhyolite porphyry dikes flanking a large 1300 m by 2100 m breccia complex. Recognition of the potential for the buried molybdenum porphyry system was based on quartz-molybdenite vein fragments within the hydrothermal breccias.The full extent of the molybdenum mineralization is not known. The few deep drill holes along one comer of the breccia complex defines strong metal zoning of molybdenum and associated elements of F, Mn, Zn, Pb, Au, Ag, Fe and W about the molybdenum stockwork mineralization that may be useful for guiding additional exploration. The best mineralization occurred near the base of the deepest drill hole with 0.114% Mo in rhyolite porphyry near the edge of the breccia pipe at a depth of 1350 m.The exploration history of the deposit has been complex, focussing on both porphyry-style mineralization and precious metal veins and stockworks on the periphery of the porphyry system. Exploration to date has defined an attractive porphyry molybdenum system with uneconomic grades at great depth; however, there remains significant potential to define economic mineralization elsewhere in the Keystone porphyry system and adjoining occu""ences."

Jan 1, 1995

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By A. J. Sinclair, N. Champigny

"The Cinola gold deposit in the northern Queen Charlotte Islands, British Columbia, is in a clastic sequence consisting of a lower shale of the Late Cretaceous Haida Formation and an overlying interbedded sequence of pebble conglomerate and coarse-grained sandstone of the Middle Miocene Skonun Formation. Both formations are intruded by a stock and dykes of porphyritic rhyolite. Two K-Ar model ages indicate mineralization and probably porphyritic-rhyolite intrusion at about 14 Ma (middle Miocene). A splay of the Sandspit fault system constitutes the footwall on the west of the deposit.The Cinola deposit can be classed as Carlin-type based on features such as (1) small particle size for gold, (2) Tertiary age of mineralization, (3) element abundances (e.g. high Hg), (4) dominantly argillic alteration, (5) a structural setting associated with major faults, (6) porosity of the host rock and (7) spatial and possibly genetic association with felsic intrusions. Gold is widespread and occurs mainly as grains of< 0.5 11-m in silicified sedimentary rock, and in quartz veins. Locally, coarse > 100 11-m particles of native gold occur in quartz veins, especially in strongly brecciated porphyritic-rhyolite. Ore minerals are mainly pyrite and marcasite, but include small amounts of chalcopyrite, sphalerite, galena, pyrrhotite, cinnabar, tiemannite (HgSe), rutile, magnetite, hematite and limonite in addition to native gold and electrum. No silver minerals have been found; silver was found in gold particles in amounts varying from 6.2 to 24.2 weight per cent. Alteration products are sericite, illite, kaolinite and chlorite, with abundant quartz of several stages.The host rocks, specifically the Skonun Formation, formed as an alluvial plain facies in a braided river system discharging into a marine basin in early Middle Miocene time. During the Middle Miocene, this sequence was intruded by a rhyolitic stock. The highly porous and permeable Miocene clastic sequence apparently provided an optimum setting for the development of a large geothermal system, the energy for which probably derived from the rhyolite stock. Mineral deposition followed a well-defined paragenesis, which, from oldest to youngest, is: (1) precipitation of iron sulphide minerals, and early quartz; (2) several stqges of quartz veins, with deposition of sphalerite succeeded by galena, chalcopyrite and visible gold. Micron-size gold was precipitated throughout these two stages of mineral deposition. Argillitization of the host rocks probably in part coincided with the mineralization and continued during cooling of the geothermal cell.In-situ reserves have been estimated at 41.1 million metric tons averaging 1.85 g Au/tonne using a cutoff grade of0.86 g Au/ tonne."

Jan 1, 1982

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter&apos;s Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all &apos;hot-metal&apos; basis.

Jan 1, 1938

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company&apos;s underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By F. W. Gray

Summarized Foreword This paper is one of a series arranged by Institute Divisional Committees for the Fiftieth Anniversary Meeting, reviewing the experience of the major mining and metallurgical industries during the life of the Institute. The viewpoint is national and broadly technical. Geology is stressed on a continental scale without regard for provincial boundaries. The boundary between Canada and the United States is, however, so decisive a factor in our coal-mining economics and our political evolution that mention of its implications cannot be avoided. The Laurentian Shield in Canada makes the occurrence of coal deposits a geological impossibility between the St. Lawrence Lowlands and the Great Plains. All but five per cent of Canadian coal resources occur west of Winnipeg. The utilization of this ninety-five per cent of our coal wealth has to date been a consequence of transcontinental railways&apos; development, and the small fuel needs of thinly populated wheat farming and cattle-raising territory, in what- to judge from the development of mixed farming and greater population density of Manitoba- is merely an initial stage of agricultural intensification and accordant population growth. There is no useful purpose in measuring coal resource against consumption rate in the West as a whole, because the resource is but partially known, and it is difficult to believe that industrialism based upon coal utilization is in any but its infant stage of growth. Canada west of Winnipeg possesses, moreover resources of petroleum and natural gas, which, together with the power-potential in the long watershed of the eastern slope of the Rocky mountains, give to population centres such as Calgary and Edmonton a choice of energy resources that is almost an embarrass des riches.

Jan 1, 1948

By C. V. Corless

1. Introductory Some members may recall that at the Annual Meeting two years ago I read a paper, &apos;The Future of the Mining Industry in Canada." Discussing this large subject it was possible only to outline the facts and inferences leading to ?the conclusion that Canada is a country endowed with enormous mineral wealth, of which the fringes are yet scarcely touched. In the present paper, I wish to examine in somewhat fuller detail the evidence, both direct and inferential, concerning the mineral wealth of the greatest physical and geological feature of Canada-the Precambrian Shield. Many, if not most, of these facts are already familiar to you. But, since they will form the basis of the reasoning employed, they will be recalled for explicit reference. First, let us review very briefly the position and extent of the Shield. The area of the entire Shield is given in textbooks as 2,000,000 square miles, of which perhaps 10 or 12 per cent. is exposed in the south-easterly part of Canada&apos;s Arctic islands. The remainder occupies roughly two-thirds of the North-west Territory; the north-east corner of Alberta; one-third of Saskatchewan ;two-thirds of Manitoba; three-fourths of Ontario; and nearly ninety-five per cent. of Quebec.

Jan 1, 1924

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By M. Zanini, D. Wong

ABSTRACT: Metals market improvements in 2005 drove the desire to increase nickel throughput and the production of nickel oxide sinter at the Vale Ltd. Copper Cliff smelter. Significant difficulties were encountered due to the unreliable quality of Bessemer matte being produced. Concentrate feed changes and the loss of technical and operational expertise during the previous market downturn contributed to the challenge of making the required improvements. Significant progress has been made in the converter aisle by focusing on employee engagement and standardizing best operating practices for a new generation of skimmers. This paper documents these initiatives and seeks to balance the art and science of converting.

Jan 1, 2012

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By J G. Brady

This paper discusses the ceramic products used in the construction industry in Canada, as well as the main raw materials used in their manufacture. The products include the! following: (1) clay prorlucts -such as facing brick (glazed and unglazed), common brick, facing tile (glazed and un-glazed), terra cotta, load-bearing tile, non-load-bearing tile, structural clay floor tile, quarry tile, drain tile, sew-er pipe, conduits .and flue liners -which are made mainly from domes-tic common clays and shales and from domestic or imported stoneware clays and low-grade fire clays; (2) floor and wall tiles of the whiteware type, which are produced from ingredients such as kaolin, ball clay, feldspar, nepheline syenite, talc, pvro-phyllite and wollastonite; (3) glass products -the major ones being sheet glass, plate glass and mineral wool (glass wool, and rock or slag wool) -which are made from such materials as silica sand, soda ash, salt cake, feldsspar, nepheline syenite, dolomitic limestone, high-calcium limestone. borax and (for rock and slag wool) various rocks or slags;

Jan 1, 1963