Search Documents

By L J. Reynolds

Gold mineralisation at the Globe Progress deposit is hosted by a geologically complex zone of shearing and brecciation, within a package of deformed metasediments. Mineralisation styles range from quartz breccias and lodes to sheared clay pug zones and disseminated sulfides. A review of the diamond drill core intersections through the deposit indicates that critical hanging wall and footwall contacts can be a combination of sharp or gradational; visual or non-visual boundaries. Approximately 60 per cent of mineralised contacts can be confidently identified visually, particularly where associated with veining, distinct brecciation or shearing, and high sulfide content. However, the gold grade and distribution of disseminated mineralisation can be extremely difficult to estimate visually, with implications for resource estimation and grade control when mining. Using observed drill hole geology and assays, a new geologically based model for the gold mineralisation has been constructed for the deposit to reflect the expected variability of the mineralisation contacts. This new model will constrain resource estimation and also serve to act as a predictive model when open pit mining commences. Nevertheless, careful grade control practices such as drilling, trenching and supervised extraction of ore will be required to maximise ore recovery and minimise dilution during open cut mining.

Jan 1, 2006

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

Over the past 15 years many world-class gold discoveries have been made in the region. Some deposits, such as Lihir and Porgera in P.N.G., have a contained gold resource that places them among the top dozen deposits ever found on a worldwide basis. Can we see any pattern to these discoveries, or are they the result of good luck or chance by geologists and prospectors who struck it rich? Whilst such discoveries were a feature of the gold rushes of the 1850s and the 1900s, the present boom is now scientifically based. This paper develops an argument that long-tent, multi-disciplinary exploration by experienced geoscience teams underlie the successes achieved. Dis- coveries nearly always reflect a combination of skills, drawn from the areas of geology, geochemistry, geophysics and remote sensing, and a team approach. They do not represent the chance finds of a prospector's pick or such as the Norseman discovery where the gold reef was first noted by the prospector when his horse fell over the outcrop. The following deposits provide major examples of exploration successes within the Australian-Pacific region, it is not an exhaustive list and I have noted other significant producers at the end of this paper. For the Australian mines listed and based on our estimates for 1990 gold production, they represent about 20 per cent of the Australian production total.

Jan 1, 1991

By Hood M

Rock cutting excavation technologies and particularly continuous excavation technologies, can offer benefits in the areas of reduced costs, higher revenue and increased safety in a variety of mining situations. Non-explosive rock excavation technologies for example, can deliver significant benefits in the areas of dilution and improved ground support (no overbreak). This paper is an attempt to focus on the development and future of alternative rock breaking technologies and to provide some insights as to why and how we should proceed in this direction. The market size for underground hard rock excavation technologies is examined. A short review of the evolution of various rock excavation technologies in terms of cost and production rate is given and a summary of the state-of-the-art technology is presented. Mechanical excavation technologies (TBM) have very high production rates compared to D&B and the gap is widening, however, they have not been successfully applied to mining applications. Operating costs for mechanical and D&B systems have been dropping over time, however, D&B costs are the lowest. Given the current state of knowledge it appears that with regard to hard rock underground metalliferous mining that R&D efforts should be focussed in the following areas - disc cutter tool development (materials and design; operation; presentation to the rock surface), hybrid cutting systems (consisting of water jets and disc cutters) and development of pressurised hole breakage technologies. It is also possible that two techniques known as the pulsed laser and pulsed water jets may have some potential. The generally agreed specifications for a widely applicable underground hard rock excavating machine are - disc cutter based, a minimum production rate of 100 t/h, be flexible, manoeuvrable and deployable, weight of less than 100 tonnes and be economically competitive with D&B in rocks over 150 MPa UCS. Such a machine would seriously challenge the position of conventional D&B in a wide range applications and provide some of the benefits of mechanisation and automation that the mining industry is pushing so hard for. However, technology developments in the D&B area are not static and hence the target is moving and is increasingly difficult to overtake.

Jan 1, 1995

In the mining and minerals industry, development, introduction and construction of new plant designs, to meet sustainability objectives, face a series of major hurdles. Typical are the long investment cycle times, the designer does not normally control the spending (the owner does), and the industry is inherently technologically conservative or risk adverse while accepting the often more significant geological, market and political risks.æSustainable Plant DesignÆ is an approach to plant and facility design that drives the necessary culture change and acceptance by minimising technical risk and maximising potential returns. The approach forces consideration of sustainability objectives and risks early in the project, where cost saving and efficiency improving opportunities can be maximised.In Hatch, we are using three proven tools under the ærisk managementÆ umbrella to drive sustainable development principles into our projects:Sustainable Plant Design, FutureWatchTM Reviews, and Clean Plant DesignTM . These proactive practical, not theoretical, techniques for driving change from within and reducing whole of life cycle costs will be discussed and illustrated with case studies.

Jan 1, 2004

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

A good deal of criticism has been levelled at Mines Division over the slowness of processing mining privilege applications, some of which is justified and some which is not. There are many reasons for delays in the processing of applications and not the least of these delays are caused by the applicants themselves.

Jan 1, 1982

To secure a sustainable competitive advantage some smelters may need strategies based on flexibility in feed and product ranges depending on immediate future projections of profitability. This paper explores the technical requirements for strategic diversity in smelting, leaving procurement, marketing and contractual considerations aside. The days when a smelting operation is tied specifically to say only processing zinc concentrates are perhaps drawing to a close. While internationally traded mineral concentrates are available, attractive business opportunities must exist for fully diversified custom smelters. Certain new and emerging technologies have inherent characteristics that are evaluated in this context. The paper identifies the basic building blocks that will permit such a scenario and assesses the technical feasibility. The ability to respond flexibly to environmental pressures is highlighted as being of paramount importance.

Jan 1, 1996

By Kolarczyk M

When controlling the ventilation process in a deep mine some knowledge of the sensitivity of the air volume output to changes in the resistances of network side branches is of great advantage.Sensitivity is taken to mean the limit of the differential quotient AV /ART where AV. is the change in air output in the i--h side branch caused by a change of resistance LI R in the r-th side branch. A method Is presen- ted for determining any arbitrary co- lumn of the sensitivity matrix. A network interpretation of this met- hod was developed in which an ancilla- ry network additional the basic network is constructed and solved, giving an analysis of the sensitivity signs de- pending on the structure of the network.

Jan 1, 1988

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

Kidston Gold Mines Limited (70 per cent Placer Pacific and 30 per cent Public Shareholders) has been mining the Wises Hill Pit since late-1984. The Wises Hill Deposit is a large low grade gold deposit and as such is highly sensitive to economic parameters. The uniformity of the orebody has allowed a bulk mining method to be used, with minimal dilution. Total reserves defined to-date are 64 160 OOOT at a grade of 1.60 g/t gold. Mineable reserves remaining as of January 1992 are 36 357 OOOT at a grade of 1.28 g/t gold.Mining investigations to reduce the impact of lower gold prices, the effect of decreasing headgrade and increasing mining costs have focused on wall steepening.

Jan 1, 1992

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

By Mazandarani M, Chabot L, Vichion K

Pitch-steering models have been developed for discretely advanced mining machines (such as heading machines and coal shearers) using small-angle geometry and there are illustrative examples of simulator predicted performance. Although simple linear models result from the analysis of open-based machines, sledge mounted machines require execution of a Linear Programming energy minimisation to determine the attitude of the machine base at each advance over the previously cut floor steps. An analytical approach is based on elastic beam concepts developed for such applications as longwall face conveyors, caterpillar tracked machines such as continuous miners and longhole drills. Simulation results for longhole drills show the expected performance of an automatic guidance system and the destabilizing effects of sensing deviation too far behind the drill bit. Certain drill bit boundary conditions are expected to assist TBM. steering studies in three dimensions.There is a real role in mining machine steering for the mathematical models used in flight simulators.

Jan 1, 1991

By C P. Kramers

The need to provide a sufficient quality and quantity of backfill continues to increase in South Africa, particularly as related to the increasing depth of mining. More and more applications require well designed fill systems either as classified or cemented backfill, and in some applications even tailings/aggregate based backfills. The paper discusses developments in backfill technology in South Africa with special emphasis on reliable system designs and operations, particularly as related to the preparation and hydraulic transportation aspects. Approaches for the alleviation of previous problems associated with premature pipe failures in vertical shaft columns for the distribution of tailings based backfills are discussed. Resulting from CSIRÆs developmental work, reliable full-flow systems, which can operate at low system pressures, have become a common practice, provided that backfill flowrates and internal pipe sizes are well matched. This aspect is reviewed. With regard to the tailings/aggregate based backfills the paper reviews some of the results of comprehensive in situ monitoring and the development of such systems. It is shown that a thorough understanding of the effects of aggregate top size, fines content and slurry relative density is required in order to ensure the restartability of temporarily shut-down pipelines. Some innovative technologies for the comminution of development waste underground to yield aggregate products potentially suitable or hydraulic transportation and backfilling, are briefly discussed.

Jan 1, 1998

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973