Search Documents

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004

By D Clarke, I Minniakhmetov

This paper describes the application of the SBRE framework to model the Olympic Dam deposit, one of the largest copper and uranium deposits in the world. Geostatistical simulations are the best practice for quantifying uncertainty in the mineral value chain and estimating resources. However, these simulations are currently undertaken on an ad hoc basis in the mining industry due to the high requirements in computing resources and capabilities in advanced geostatistics. The SBRE project provides a standard framework to test, build, and run conditional simulation workflows, which has been applied to the Olympic Dam deposit. Conventional geostatistical methods face challenges when modelling the Olympic Dam deposit, such as non-stationarity, non-linear correlations, and a large number of grid blocks to simulate. To address these challenges, a combination of methods was used, including projection pursuit multivariate transform, trend-residual decorrelation, pluri-Gaussian simulations, and turning-bands simulations. Various tools and applications were used to build the model, including in-house developed applications, Autovariogram software (Varify), and the RMSP python library. All computations were accomplished on the AWS cloud using the EC2-Batch service. The final set of simulations was validated using various methods, such as grade-tonnage curves, histograms, swath plots, and variogram reproductions, as well as validation using historical samples back-testing. The study highlights the importance of an automated, modular, and scalable framework in the development of conditional simulation workflows and describes the learning gained from trials of different combinations of methods and software

May 24, 2023

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

By M Szwec, P Corbett, P Sheffield

Centennial Coal operates the Springvale and Angus Place longwall mining operations that extract coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale and Angus Place mines have a history of difficult geotechnical conditions, where mining operations are conducted with a thick coal roof interbedded with numerous claystone units and relatively high levels of vertical and horizontal stress. The combination of a relatively high stress regime and weak laminated roof has led to numerous roof failures throughout the mine’s life.Following underground roadway development, the mine roadways can experience high levels of roof movement that can lead to roof falls. Two-point wire extensometers (known as ‘telltales’) are extensively used for roadway condition monitoring. Along with extensive other geological and geotechnical data, monitoring data is used to prepare geotechnical hazard plans that are then used in all areas of mine planning to allow for safe and efficient operation of the mine.This paper presents a case study of the use of a new software tool that allows time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. It can be used in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological/geotechnical data to allow correlation of monitoring data with risk factors.CITATION:Corbett, P, Sheffield, P and Szwec, M, 2014. A new tool for extensometer data analysis and improved understanding of geotechnical risk factors, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

In narrow orebodies the use of ordinary kriging (OK) may pose certain limitations when used for grade control modelling. The smoothing effect of kriging, by its very nature, cannot retain or accurately characterise the dispersion (variability) that is inherent in gold deposits. This dispersion is a critical component of determining the desired level of ore loss and dilution.Fixed block model positions used in OK, and all estimation approaches, within a grade control process may never align with the ‘true’ ore boundary. This may lead to excessive ore loss and dilution, especially within narrow lodes.Using a risk-based approach to ore block design based on the geostatistical method of conditional simulation (CS) can highlight the differences achieved when an alternative method to OK is used for grade control modelling. By using a mesh of nodes and the application of a ‘transfer function’ to the simulation models, the position for ore contacts can be better assessed than when using fixed blocks in OK. Therefore, the value of various ore block boundaries can be better analysed by objective assessment of ore loss and dilution for a given minimum mining selectivity (selective mining unit or SMU), even in narrow lodes.A case study of a narrow vein gold deposit, comparing the results from an OK model and a CS model shows that whilst both models show similar trends – waste, low-grade, and high-grade regions are the same in both cases – the simulation model can provide greater insight for optimal definition of the mineralisation boundary.CITATION:Haylett, M E, Weeks, A, Matthews, G D and Khosrowshahi, S, 2014. Ore block design in narrow vein gold deposits – estimate or simulate?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 421–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D H MACKENZIE

In common with several great orebodies and mineral camps around the world Broken Hill has been the subject of state-of-the-art technical and scientific scrutiny during its long working life. During the early years geological interest in Broken Hill tended to be directed at the body for its intrinsic scientific worth, mainly on account of its large size, high grade and wealth of mineral species. For much of the last 60 years the interest has had a more applied motivation, namely, to assist the search for either repetitions in the Broken Hill field or analogues in other terrains. This paper looks at the major changes in geological concepts and exploration techniques applied at Broken Hill and attempts to assess their impact.

Jan 1, 1992

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By T J. M Harvey

This paper gives an overview of the ASHRAE LibHuAirProp, CoolProp and REFPROP software packages. These packages were predominantly developed for heating, refrigerating and air conditioning engineers and the refrigeration and steam power industries, although CoolProp and REFPROP also cover combustible gases. The main aim of this paper is to highlight the existence capabilities and status of the different packages and where they can be used. The paper gives typical examples of the use of these software packages, specifically as Excel add-ins, and provides a comparison of results of typical mine psychometric and gas drainage calculations using the packages and more traditional ventilation and gas drainage calculation methods. The paper also introduces a hybrid method that improves accuracy compared to traditional methods. In typical mine situations, the use of software packages is probably not required; however, with the increasing accuracy of instruments, potential greenhouse emission costs and the sale of mine gas, more accurate measurements and calculations can potentially save (or make) significant sums of money.CITATION:Harvey, T J M, 2015. The use of psychometric, thermodynamic and transport property software in mine ventilation and gas drainage calculations, in Proceedings The Australian Mine Ventilation Conference, pp 201–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A R. Penney

Safety management, both personal and that associated with catastrophic hazard, helps to define the success of mining companies. Personal safety management, often categorised by slips, trips and falls, has been widely addressed, with numerous approaches successfully adopted. Catastrophic hazard can lead to a single accident (eg ground collapse, underground fires etc) causing multiple fatalities. Catastrophic hazard management in mining is an emerging discipline, and as such there are various pitfalls to demonstrate its effectiveness and success; it is much more than simply meeting regulatory requirements. Various standards, guidelines, and leading practices are available for reporting key performance indicators. While measuring and reporting safety related key performance indicators (KPIs) such as Total Recordable Injury Frequency Rate (TRIFR), Lost Time Injury Frequency Rate (LTIFR), are important, they often lack detail, and give little insight into the effectiveness of catastrophic hazard management strategies and controls. Catastrophic hazards are low likelihood, high consequence events, and as such demand a different management approach. Companies cannot use the suite of personal safety metrics to help demonstrate management of catastrophic hazards. In-field verifications have revealed that senior management commitment to safety is often clear, well organised, and resourced. However, there are often some inconsistencies between what management promotes and plan, to what the operational teams understand and implement. Communication and clear understanding of expectations were the common themes identified to help empower supervisors to reinforce requirements of catastrophic hazard management. A lack of specific, measurable, and time-sensitive goals and objectives for the short- or medium-term, making it challenging to track progress was another key observation. Development of an integrated, multi-disciplinary auditing process executed by an experienced team of technical subject matter experts, provided an in-depth understanding of the requirements of catastrophic hazard management. Areas such as underground fire prevention, explosive storage, electrical safety, mobile vehicle interactions, ground control, inrush, and shafts and winders management have substantial overlap and intertwined processes, and similar strategies for emergency responses. Auditing of catastrophic hazards and safety management systems compliance is only the first step in safety assurance. Completing operational performance audits in technical areas and benchmarking the site verification of safety management documents and verifications forms a critical part to clearly demonstrate industry leading safety practices. No longer is it the external inspection or regular hazard management plan review requirements that dominate, but rather the culture of continual hazard identification, management, controls verification, underpinned by improvement and follow-up verifications of the corrective actions.

Mar 29, 2023

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

By K Grohs, A Satriawan, S R. Pearce

Martabe gold and silver mine is operated by PT Agincourt Resources (PTAR) and is situated in northern Sumatra and comprises several deposits in steep terrain, and in a tropical climate, that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste rock from excavations and tailings from processing is a by-product to be scheduled and used for a number of purposes identified as part of life-of-mine planning. These uses include construction of the current integrated tailings storage facility (TSF) as well as future engineering construction and waste disposal projects which includes plans for a program of in-pit backfilling. These plans need to be aligned to ensure the waste rock and tailings can be contained relative to the production rate. Given that the site will have multiple open pit voids upon cessation of mining activities opportunities for integration of in-pit disposal of mine waste have now been assessed with technical studies to review the practicality of the approach with respect to operational challenges and conformance with closure planning requirements. This includes assessment of disposal of waste rock, tailings (including consideration of filtered tailings) and co-disposal of waste rock and filtered tailings.

Aug 2, 2023

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By E Gabriel, J C. Koppe, A Gomes and P Crispim, R Schaarsdmit, I Pablos

Drill and blast (D&B) is one of the most important production operations in open pit mining. The resulting fragmentation of the D&B reflects in the downstream unit operation. Good fragmentation of the ore will minimise the cost of loading, hauling and crushing. The understanding of the geological model integrated with a software system for bench face surveying and planning of blast layouts based on three-dimensional images can help to achieve the fragmentation goals of the mine operation. A case study integrating these tools was carried out in a large iron mine in Brazil. The iron ore in the study area consists of hard and friable itabirites. More than three different ore types may occur on the same bench. Under these conditions, data integration becomes necessary to improve the results of blasting. A blasting plan was based on the generated geological model. The methodology helps understanding the factors that can interfere in the fragmentation process, allowing defining actions that can improve the blast design in those places that fragmentation wasn’t achieved. This condition is important for a continuous improvement of the drilling and blasting operation. In comparison with the previous blasting carried out at Itabira mine, which did not take into account the geological model, substantial improvements in fragmentation were observed, eliminating the need for secondary blasting.CITATION:Schaarsdmit, R, Pablos, I, Koppe, J C, Gabriel, E, Gomes, A and Crispim, P, 2015. Geological modelling and bench face survey to improve blasting fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 401–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Kim, M J. Sun

Global steel companies are actively combating climate change by reducing carbon emissions. Traditional steel production, using the blast furnace (BF) – basic oxygen furnace (BOF) process, heavily depends on coal and emits substantial CO2. To mitigate this, companies are transitioning to the more eco-friendly DRP (direct reduction plant) – EAF (electric arc furnace) process, which lowers CO2 emissions. This study quantitatively evaluates the impact of increased hydrogen consumption on the carbon footprint of product (CFP) through an analysis of direct reduction process heat and mass balances. The study prioritises a comprehensive material balance based on mass conservation principles. The heat balance is calculated using differences in enthalpy through state energy properties, avoiding heat consumption. Validation using operational data from Hyundai Steel Dangjin works’ blast furnaces shows close alignment between calculated results and actual data, with less than 1 per cent error. This methodology facilitates a detailed analysis of the direct reduction process, offering insights into its feasibility and efficiency. Analysis of the operational impact by increasing the hydrogen ratio demonstrates reduced CO2 emissions and increased heat requirements due to the endothermic nature of hydrogen reduction, in contrast to the exothermic CO reduction. Possible solutions include raising reducing gas temperature or enhancing flow rate. The study effectively utilises designed heat and mass balances to assess material quantities and thermal balance under different operational conditions. It lays the foundation for the initial direct reduction process design, aiding in deriving and optimising operational parameters. Additionally, it provides valuable insights into the challenges of increased hydrogen, contributing to the production of greener steel by addressing these issues.

Aug 21, 2024

By P Craig, I Canbulat, J Naylor, J Emery, A Sykes

Longwall mining is by far the most common method of underground coal extraction in Australia. Industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. Longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin-encapsulated bolt installation is still the principal method used in all major coal producing countries around the world. Anglo American realised that an opportunity existed to introduce an alternative roof bolt installation technique called ‘spin-to-stall’ (STS) into Australia. STS was first introduced by Anglo American Coal in South Africa, where it has been successfully used for over a decade, though implementation of South African STS resin in Australia has proven to be near impossible. Therefore, a new STS development project was initiated between Anglo American Coal and Jennmar Australia. This paper summarises the journey of this project, the results achieved and the successful implementation of STS at Grasstree mine.CITATION:Emery, J, Canbulat, I, Craig, P, Naylor, J and Sykes, A, 2014. Development and implementation of spin-to-stall resin at Anglo American’s Australian Underground Coal Operations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990

By S J. Henderson

Over much of Australia, rainfall is highly seasonal and storm-driven. Consequently, operational mines often need extensive earthworks – drains, dams and levees – for protection during the occasional large floods and for water storage against the dry times; however, it has not been appreciated that many of these earthworks will need to function after mining has finished, sometimes, beyond a normal design life for engineered structures.While a mine is operating, standards for design and maintenance are dictated by regulation and risk assessment. For dams and levees – regulated structures – the standards imposed mainly relate to life-of-mine. The levels of risk and maintenance accepted by the mine operator may not be acceptable to another landholder in perpetuity. However, the Environmental Authority cannot be surrendered unless the landholder has accepted responsibility for any unrehabilitated regulated structures (Department of Environment and Heritage Protection (DEHP), 2016).In order for a future landholder to be willing to take responsibility for a dam or levee, the structure should be of value to the business of the property. In addition, its management needs must be consistent with that business; for example, it should be maintainable using skills, equipment and materials normally available to the business.CITATION:Henderson, S J, 2016. Earthworks or landforms? Designing for lease surrender, in Proceedings Life-of-Mine 2016 Conference , pp 151–153 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016