Search Documents

As partition curves are widely employed to characterize screening efficiency which, by definition, should include a time parameter, it is shown, perhaps for the first time, that time is already included in the partition curves and how. Laboratory and plant results are used to show how screening efficiency depends on feed composition, near-mesh and oversize material and screen motion, and how these factors may combine to give an erroneous result that two identically efficient screens are different and two screens of different efficiency are identical. Reasons are given which show why a renewed interest in screening would benefit not only screen engineers and operators but also those concerned in formulating standard specifications of screen analysis methods.

Jan 1, 1984

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists essentially of a mineralized bituminous shale sequence that incorporates tuffites, numerous graded beds, and isolated but massive slump breccia horizons.The principal sulphides are' pyrite, sphalerite, and galena. These occur mostly in the shales. The accompanying turbidites contain only minor mineralization.The geochemistry of the deposit has been investigated in relation to the stratigraphic column and mineralogy of the sediments.A sedimentary origin is proposed for the deposit. Volcanism, thermal spring activity, salinity, regional faulting, and climate are examined as possible factors that may have contributed to sulphide formation and which could be used as criteria for mineral exploration.The metallurgy 'of the McArthur deposit is discussed in terms of its geological history.

Jan 1, 1972

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

By Wharton C. L

This paper describes a new computer program which can significantly increase the Net Present Value of either an open cut or underground mine by optimising the cut-offs used during the operating life of the mine. It was developed over a period of about three years by Whittle Programming Pty Ltd of Melbourne, Australia. Several authors have contributed to the theory behind this work, but the ideas were further developed, consolidated, and clearly explained by Lane (1988). It was this book that triggered the development of the new program. The paper starts with an explanation of the theory behind this type of optimisation, and then goes on to describe the computer methods used to optimise the different parts of the problem.

Jan 1, 1995

By Shu DM, Moxon P

Subsidence profiles over longwalls at West Cliff Colliery (WCC) are predicted by three methods, NCB Emperical Method, Salustowicz's Profile Functions and Superposition of Two Critical Profiles. A method of deriving maximum subsidence using local data is also presented. For the first four longwalls, the results are compared with those from the subsidence surveys conducted during and after the extraction of each longwall. Longwall V has not yet been extracted, so the results are for the predicted subsidence profile. Superposition of two critical profiles is carried out in an attempt to check the principle of superposition. In addition, strata movement above the extracted longwalls is discussed.

Jan 1, 1986

This paper refers to the open cut mining practice developed at Western Mining Corporation's Kalgoorlie Gold Operations (K.G.O.). Mining activity was centred attwo areas, namely W.M.C.'s Siberia "Sand King" and"Missouri" open cuts plus W.M.C.'s "Great Boulder" and K.M.A.'s "Horshoe" and "Morrison -Hannan's Star" open cuts in Fimiston.Kalgoorlie Gold Operations was set up initially to look after W.M.C.'s open cut interests in and about the Kalgoorlie area. The first mine commenced was, the Sand King open cut, approx 75 km NW of Kalgoorlie. it was here that the requirement for a highly selective form of mining first became apparent.

Jan 1, 1984

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By Kirkhouse C. B

Soon after the Broken Hill Limited started operations at their Iron and Steel Works at Newcastle, NSW, it was found necessary to install a mill for rolling small merchant bars, rounds, etc.An arrangement of the first mill laid down is shown on Plate 1., Fig. 1. This mill commenced operations on the 18th July, 1917.The feed for this mill was rolled in the existing 18-in. mill and sheared to the lengths required before being delivered to the billet storage yard. The billet storage yard is 90 ft. span, and is served by one 10-ton electric overhead travelling crane. Billets were placed on the billet bed preparatory to being charged into the heating furnace.The heating furnace was of the continuous recuperative with end discharge and had a hearth 40 ft. long by 10 ft. wide. The billets were pushed through the furnace by means of two hydraulic rams, which could either act together and push one row of billets, or act singly and push two rows of billets. This furnace was fired by producer gas from the producers shown on Plate I., Fig. l.The gas was conveyed to the furnace by means of a brick underground flue.

Jan 1, 1935

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

By Hill G

The Boddington Gold Mine (BGM) is managed by Worsley Alumina Pty Ltd (Worsley) and is located 110 km south-east of Perth, Western Australia. The gold mine, which has operated since mid-1987, was originally constructed to treat 3 Mtpa of gold bearing oxide ores, has subsequently been expanded to treat 7 Mtpa and is presently one of the largest gold producing operations in Australia.During 1990 a Supergene/Basement Plant was constructed to treat 250 000 tpa of copper supergene and hypogene ores and basement ores which contain significant gold grades and which are encountered at the lower levels of the existing oxide orebody. The SupergeneBasement Plant has the versatility to treat a wide range of ore types, producing both gold bullion and copper-gold concentrates. It is a stand-alone facility adjacent to the existing 7 Mtpa gold plant.

Jan 1, 1992

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2008

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

Designing for early access to deep orebodies is an essential driver for improved project payback. Vertical shaft sinking techniques have been developed to allow concurrent mine level excavation while continuing to sink. Project cash flows can also be improved when simultaneously deepening existing shafts beneath operating hoisting systems. Further economic advantage has been realised through creative sinking sequencing in twin ventilation/service shaft projects. A fourth technique to reduce project schedules involves partial shaft barrel equipping allowing unrestricted access to construct stations and continue with level installations. This approach reduces interference with barrel sinking activities to insignificant proportions. This paper reviews how these approaches have added significant value to actual shaft sinking projects, as assessed from a contractorÆs perspective, and discusses some of the practical issues to be addressed when planning future projects. Designers need to take cognisance throughout all project engineering phases of the adage that you are only sinking when cleaning the face. Cleaning can only be sustained when there is sufficient hoisting capacity.

Jan 1, 2005

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

The scarcity of truck tyres combined with decreases in the availability of labour, increases in fuel costs and a buoyant international economy driving project budget blowouts, have all combined to change the paradigm behind mining equipment selections. The escalation of commodity prices has occurred in parallel with an increasing maturity in continuous mining machinery, mobile in-pit crushing systems and very large-scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in-pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

Jan 1, 2007

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

At Pasminco Mining's South concentrator. which was commissioned in 1952. an expansion. modernisation and efficiency improvement program commenced in 1986 with a coarse ore stockpile and grinding circuit expansion. the replacement of small flotation cells and the upgrading of reagent mixing and metering equipment. The program continued with the installation of a TDC 3000 based process control system (1988) and concentrate thickeners (1990). By mid-1991 a further grinding expansion and the installation of zinc flotation feed regrind ball mills and zinc recleaner column cells will be complete. leaving the use of ceramic disc fillers and development of process control strategies as probably the remaining major avenues for improved process efficiency at present.

Jan 1, 1991

Esso-BHP have installed a Production Supervisory Control System that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control. The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexability to handle future variations in operating conditions. Thn -etom ..ill kn nvt,,ndnd to thn I-lalihn+ rJ,+f, rr , Into +hie -- -A +n the lei...,fieh .,lo+fnrmc A.,;- 1071

Jan 1, 1970

By English W, Poppit I

COALEX Pry Limited operates two underground steaming coal mines on the western edge of the Sydney Basin near Lithgow, New South Wales. Baal Bone Colliery uses longwall technology for an output of over two million tonne/year while Clarence Colliery currently uses continuous miners and breaker line supports for an output of two million tonnelyear.A computerised geological database and modelling system has been implemented to service these mines routinely, as well as several outlying prospects. The database is constantly upgraded for drillhole information, surveyed spot levels on the surface and underground, quality sampling details, surveyed mine workings and geological mapping. This information is edited on a routine basis, allowing dynamic modelling of key aspects of geology for ongoing operations.

Jan 1, 1991