Search Documents

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By J Butler, N Patel, S Narendranathan, S Rastogi

The Yallourn Mine (YM) commenced mining of brown coal in the 1920s under operation by the State Electricity Commission of Victoria (SECV), prior to it becoming privatised in 1996. The present owners of the YM, Energy Australia Yallourn (EAY), acquired the site in 2000 and intend to continue operations until scheduled closure in 2028. Brown coal extracted from the YM is fed into the Yallourn Power Station which supplies approximately 22 per cent of Victoria’s electricity. Water within the YM is collected and stored in the Township Field Fire Service Pond. Water levels within the Fire Service Pond (FSP) may fluctuate considerably depending on the requirement for storage at the site. With due consideration to the stability performance of mine batters adjoining the FSP, the authors performed slope stability assessments to evaluate the risk and consequence of batter instability during the potential pond filling as it approaches the ‘critical pool’. The critical pond is defined as the level at which the driving forces (destabilising forces) are at their greatest and the resisting forces (lake forces, friction) are at their lowest. This assessment was undertaken using the Mine Geotechnical Risk Index (MGRI) approach.

Aug 2, 2023

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H-S Yang, H Park, S-J Kim, Y-H Ko, H-S Kim, S-H Cho, J-K Kim

An investigation was undertaken to devise a new method for reducing dust spread during blasting demolition utilising water tube and detonating cord. Modelling of smooth particle hydrodynamics (SPH) with AUTODYN software was initially completed to determine the expected diffusing behaviour of the water tube. The actual behaviour was then captured with high speed videos during each experiment, and each result analysed in detail. Water mist diffusion was generated and analysed by changing three key variables. In sequence, these included changing the location of detonating cord in the tube, the charge quantity and the tube diameter.As a result of experiments and simulation, optimum design for ideal diffusion behaviour was suggested and each behaviour of water mist was classified by diffusing shape of water tube as the design criteria.CITATION:Ko, Y-H, Kim, J-K, Kim, S-J, Park, H, Kim, H-S, Cho, S-H and Yang, H-S, 2015. Mist diffusion experiment and evaluation of water tube for blasting demolition dust control, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 809–814 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By Beavis FC, Box JC

The important chemical and fluid flow phenomena in heap, dump and in situ leaching are summarised. Published, quantitative models of these processes are critically reviewed, and their potential applications outlined. Comparison between the independent predictions of one of the models and column leach test data reported by others confirms the potential. Some recent developments by the authors in the fields of fluid flow through unbroken ore and modelling of the more complex chemical systems are briefly Described.

Jan 1, 1981

By A Hughes, J Agius, T Ferguson, A Parbhakar-Fox, D Lester, L M. Jackson

Management of historic tailings is a major challenge facing the mining industry and its regulators. However, through improved mineralogical and chemical characterisation of such materials the opportunity to develop better rehabilitation strategies arises. Microanalytical techniques including microscopy, mineral liberation analysis and laser ablation inductively coupled plasma mass spectrometry (ICPMS) allow for improved tailings characterisation – but the challenge posed by these techniques is how to use them effectively. Additionally, data sets collected by such techniques must be properly integrated, only then can they assist in the identification of the most appropriate rehabilitation strategies. A study conducted at the Old Tailings Dam (OTD) located at the Savage River Mine, Tasmania allowed for the integrated use of several microanalytical techniques to help evaluate the benefits of a shallow water cover as a potential rehabilitation strategy. Samples (n = 144) from 14 trenches and 11 boring cores (2 m maximum depth) were collected across the OTD. These were subjected to routine acid-base accounting, with a subset subjected to detailed mineralogy using a modified sulfide alteration index (SAI), X-ray diffractometry and mineral liberation analysis (MLA). In addition, representative samples (n = 6) from across the OTD were subjected to laser-ablation ICPMS to characterise the pyrite chemistry. Our results showed that tailings in the northern area submerged under a natural water cover were relatively unoxidised from approximately 1 m depth, with SAI values of 1 to 2. Tailings from the subaerial southern portion were extensively oxidised to approximately 35 cm depth (SAI = maximum 5.8), with fresher materials observed underneath (SAI = 5 to 5.8). Pyrite from across the OTD is enriched in Co, Cu and Ni. Through the integrated application of microanalytical tools, we determined that establishing a water cover of at least 1.5 m depth across the OTD is a suitable rehabilitation option for this historic site. However, consideration for the reprocessing of these tailings to extract Co should be further investigated.CITATION:Jackson, L M, Parbhakar-Fox, A, Hughes, A, Agius, J, Ferguson, T and Lester, D, 2015. Microanalytical evaluations of the savage river old tailings dam, north-?west Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 111–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Coleman

The flotation mechanism plays a key role in the flotation process. It is used to provide the contact between solid particles and bubbles and also the energy for these particles and bubbles to attach. The mechanism must therefore provide sufficient mixing to keep the solids in suspension so that they can be transported into the froth and recovered to the concentrate. The design of the mechanism is critical and over the past decade Outotec has developed and optimised a new mechanism design to improve metallurgical and energy performance. The FloatForce® mechanism consists of a rotor and stator arrangement and has been specifically designed to provide sustained mixing at higher air flows and lower power inputs.Over 500 FloatForce® mechanisms have been installed in existing and new operations. This paper outlines the technological aspects of the FloatForce® mechanism and provides metallurgical, operational and energy performance results from a number of flotation circuits in which these have been installed.

Aug 8, 2011

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H Utama, hi, A Suw

PT. Indo Muro Kencana (PT.IMK) is gold and silver mine located in Central Kalimantan province, Indonesia. Mining activities in PT.IMK is conducted in Bantian pit area by applying surface mining method and using combination of excavator and hauler (articulated dump truck and rigid haul truck) as the transportation for ore to the crushing plant and waste material to the waste dump. Current blasting practice is ore-waste blasting. Ore-waste blasting is the term where the ore and waste rock are blasted in the same blasting process. Blasting is conducted by using nonel initiation system. By multiple pits operation, monthly powder factor is varied from 0.23 kg/t to 0.27 kg/t. Emulsion blend with density 1.15 g/cc is used as bulk explosive. At this stage, the concept of geoblast is proposed as an engineering tool for Drill and Blast engineering practice in PT.IMK. In addition, there is a need to maintain rock fragmentation by blasting, to maintain monthly powder factor, and to maintain excavator’s productivity. Next, the concept of scaled depth of burial (Chiappetta and Treleven, 1997) and the concept of blastability index (Lilly, 1986) are proposed as geoblast’s tools to improve blasting practice in PT.IMK. It is expected that rock fragmentation by blasting, explosive consumption and excavator’s productivity will be maintained by integration of geoblast and drill and blast engineering. Furthermore, the objective of this paper is to integrate geoblast and drill and blast engineering in order to create an engineering guideline in PT.IMK. Additionally, blasting trials with air decking application is proposed in order to support the geoblast’s improvement. It is planned that these blasting trials will be conducted in 2022. In conclusion, it can be seen that integration of geoblast and D&B engineering in PT.IMK is relevant to improve current drill and blast current practice and applicable to maintain rock fragmentation by blasting.

Nov 29, 2022

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By J Crosbie, M Lord, R Bitencourt, P Defferrard

The MMG Century mine, which is the largest zinc/lead mine in Australia, began operating in 1999 and ceased mining from the open pit in July 2015, with processing completed in early 2016. Closure plans were developed from 2006, and detailed planning for closure commenced in early 2011 with the appointment of a dedicated closure planning resource. The site will continue to be managed during the active and passive closure phases to complete rehabilitation commitments and demonstrate that closure completion criteria have been achieved.Completion of the mining/processing phase of the project provides an opportunity to reflect on successes, missed opportunities and lessons learnt with respect to planning and execution of mine closure. This paper highlights examples of success at Century and also identifies key learnings and areas for improvement in progressive closure outcomes. Specific examples examine mine planning and execution involving bulk movement of waste rock and construction of permanent waste encapsulation landforms. The paper also provides recommendations for other sites that are planning for closure.Decisions made during the operational phase of the project life can result in a significant increase in closure liability and reduce the likelihood of achieving lease relinquishment. Likewise, it is of paramount importance to assess the consequences and thoroughly understand the risks associated with changes or deferral of closure plans, progressive rehabilitation targets and closure related key performance indicators.CITATION:Lord, M, Bitencourt, R, Crosbie, J and Defferrard, P, 2016. Closure planning lessons Learnt from the Century mine, in Proceedings International Mine Management Conference, pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Alternatively are they a necessary evil'? Exploration geologists are a much higher profile group but then again the higher they are the bigger they Bill. At a mine site they are reluctantly being accepted as equals by mining engineers given the requirements of the `Code' in the reporting of Ore Reserves. How best can mining geologists service their customers? Are more revealing questions to be answered in who are their customers? In the past mining geologists lived isolated existences pouring over plans and sections, now with user-friendly software packages available and the use of LAN, mining geologists and mining engineers talk electronically - God forhid what the future might hying - they might even talk to accountants and metallurgists!

Jan 1, 1997