Search Documents

Dimension stone is the term generally given to rock used in building construction. During early European history in Otago, locally available dimension stone products were easily obtained. Crude rock shelters built on river banks with schist rock within Central Otago soon gave way to more established and sophisticated permanent homesteads constructed with the same materials. Victorian architectural achievement is celebrated in Otago with many fine bluestone block buildings. When the University Council decided to build substantially in stone, it narrowly escaped disaster. It was well known at the time that brick in Dunedin was of an inferior quality and that it soon wasted. Rev Dr Stuart said before the 1879 Commission that æthe Council had some old-world notions and liked to have the University with some architectural styleÆ. Contemporary utilisation of dimension stone is generally restricted by expense to a simple veneer. Stone products produced from Otago quarries have found ready markets in other areas in New Zealand , particularly prior to the share market crash in 1987.

Jan 1, 1992

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Grano S. R, Ralston J

It is the perennial problem most metallurgists face when examining data collected from laboratory float tests and plant surveys - there are more numbers than we know what to do with! The objective of this paper is to analyse and interpret a set

Jan 1, 1994

As a result of the rapid economic growth in Japan, environmental problems have become a national concern in the latter half of the In 1967, the Basic Lair for Environmental Pollution Control was enacted as a fundamental ::olicy in this field. This lair provided compre- hensive guidelines for the action to be taken pollution prevention. The biggest problem n air pollution of those days was that of the sulphur dioxide content of the atmosphere. Based upon the law, the smelters in Japan have struggled hard to solve this difficult problem. Consequently, the ambient SO2 level has been lowered gradually year by year. At present, the ambient SO2 level is nearly equal to that in the atmospheric background. Furthermore, the fixation ratio of sulphur in Japanese copper smelters has attained up to 99.5 per cent.

Jan 1, 1980

By E Nye and T Schroeter, B Muir, M Kitson, M Gonzalez, D Mares

The single track North Strathfield Rail Underpass (NSRU) consists of a dive structure either end of a 148 m long driven tunnel skewed under three live railway tracks. The tunnel is 8 m high, 9 m wide, with a horseshoe profile, excavated by full face using a road header. Ground cover varied between 2.5 m to 3.5 m. Settlements were 5 mm to 15 mm (the latter due to a dyke). A one pass synthetic fibre reinforced shotcrete lining was installed (no lattice girders or steel sets were used). A system of automated robotic total stations was used to provide real time monitoring of the rail track and associated ground formation. No disruption to train services occurred.CITATION:Gonzalez, M, Kitson, M, Mares, D, Muir, B, Nye, E and Schroeter, T, 2014. The North Strathfield Rail Underpass – driven tunnel design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By Hommert P. J, Brown B

Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. An improved damage model based on microcrack growth in tension allows finite element calculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model.

Jan 1, 1990

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A Li, H Jinto, M Laxman

The behaviour of tailings under cyclic loading has an impact on the stability and deformation of tailings dams and a good understanding of the cyclic behaviour of the tailings under earthquakes is important for tailings engineers and tailings operators for the design and safe operation of tailings dams. This paper presents an investigation into the cyclic behaviour of tailings using both laboratory cyclic direct simple shear (DSS) testing and numerical modelling. The laboratory testing involved cyclic DSS tests on gold tailings and zinc-copper tailings under different loadings and loading frequencies. The gold tailings specimen tested at a higher loading frequency and a higher cyclic stress ratio experienced spontaneous liquefaction during cyclic shearing and the zinc-copper tailings specimen tested at a lower loading frequency and a similar cyclic stress ratio exhibited ductile behaviour and liquefied due to cyclic mobility. The liquefaction behaviour of the tailings was modelled using an advanced constitutive model (UBCSAND), which was developed specifically to model soil liquefaction and strain softening under cyclic loading. The constitutive soil model presents the nonlinear soil behaviour under dynamic loading using a hyperbolic stress-strain relation. Dynamic analyses were carried out using a finite difference program FLAC. The cyclic stress-induced excess pore water pressures measured in the laboratory were modelled using numerical simulations of the laboratory tests under different loading conditions. The results of the non-linear dynamic analyses demonstrated the capability of numerical modelling of cyclic shearing induced excess pore water pressure and the onset of the spontaneous liquefaction. The laboratory investigation and numerical modelling technique provided the key properties and parameters for the dynamic analyses to assess the stability and deformation of tailings dams under design earthquake events. More importantly, the laboratory tests and numerical modelling provided some insights into liquefaction behaviour of the tailings during earthquakes. CITATION:Li, A, Laxman, M and Jinto, H, 2018. Liquefaction behaviour of tailings under cyclic simple shear testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 250–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By F Phillips, E Deucker, J Kato

It is challenging to determine the optimal mining strategy to maximise value when a mine plan includes mineralised material which does not meet the full cost of mining but has value exceeding the variable cost of mining (‘marginal material’). Mining too much marginal material dilutes the operation’s head grade and undermines profitability. Conversely, leaving too much metal behind fails to achieve the full value of the endowment. Finding the balance between the two will maximise value delivered from the asset. This dilemma has traditionally been approached by calculating a suite of cut-off grades to define the grade of material that meets economic targets for an orebody (or zone within) and should therefore be included in the mine plan. A problem with this approach is that individual mining blocks within the zone have different costs, value and confidence levels, with each having economic co-dependencies between them. Blocks of identical grade but different mining contexts will have distinctly different economic outcomes. For example: • a block may be a low-grade increment or shell around a higher-grade stope; • a block may be available to be mined when there is spare mining capacity; or • a block may defer access to significantly higher cash flow material. Each of these circumstances would result in different value from the blocks if included as part of the mine plan. Cut-off grades calculated as averages over zones of material, or in isolation from schedule-based information, are missing the entire mining context that determines the ultimate economic outcome of making a mining decision. There are tools and techniques available to address this for open pit mining, however underground mining has different nuances. There are more intricate economic and physical dependencies between potential ore blocks, and importantly, the decision to leave material in situ can be made at any time. The case study in this paper explores a new methodology for underground mining, targeted towards strategic planning applications. It examines whether the economic logic usually applied via cut-off calculations can be implemented in the schedule so that optimal economic decisions can be made on a block-by-block basis, taking into account the mining context of the block, with the objective to maximise asset value. The results of the case study scenarios in Table 1 demonstrate the magnitude of the potential improvement in NPV that can be attained by a block by block valuation approach

Mar 15, 2021

By B W. Ham

The legacy of underground coal mining may be a land surface which, in parts, may be unstable in the long term. A case study analysis has been undertaken to explain some of the hazards and how the risk may be assessed and managed.The Ipswich Coal Measures were extensively mined with shallow underground workings, which now underlie a number of suburbs in the eastern side of the city of Ipswich in south eastern Queensland. The area was subject to underground mining from the 1840s to 1997. In general, the mines were small, family-owned operations that were restricted by complex geology, interactions with neighbouring operations and ownership of surface facilities. The oldest available mine plans date back to the late 1890s.The residents in these mining areas have a long history of unexpected mining subsidence events. A level of risk management for property owners has been implemented by the Ipswich City Council, which requires a mining subsidence risk assessment to be submitted as part of building applications for property development in the areas suspected of having mining subsidence risk. This discussion examines a series of generic subsidence events and how the risk may be assessed and managed and the hazard controlled.CITATION:Ham, B?W, 2014. The legacy of underground coal mining – mine subsidence: Ipswich coal measures case study, in Proceedings Life-of-Mine 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Kareise G. J, Leung K

The McArthur River (HYC) deposit, located in the Northern Territory of Australia, was discovered by Mt Isa Mines Limited geologists in 1955. It is one of the largest sedimentary stratiform zinc-lead-silver deposits known. Previous attempts to exploit the deposit have been thwarted by its geographical location, the capital expenditure required to establish an operation and the fine-grained nature of the mineralisation. The steeply dipping western margin of the deposit is covered by up to 25 m of overburden, and lies beneath the McArthur River and its flood plain. Dips are eastward, with the eastern edge of the deposit at a depth of about 400 m below the surface. The average thickness of the deposit is 55 m, and it covers an area of about 1.8 by 1.3 km. Seven stratiform orebodies are interbedded with sedimentary breccia, tuff and poorly mineralised siltstone. Mineralisation consists of finely intergrown sphalerite and galena, hosted by pyritic siltstone of the middle Proterozoic McArthur Group. Selective underground mining of the lower orebodies will extract more than one million tonnes of ore per annum. The dip of the mineralisation demands that mining will be by way of apparent dip room and pillar. Declines will provide access and haulage, and wherever possible development will be in ore. Initially, haulage will be by trackless diesel powered trucks, but these will be replaced by a conveyer system. A single zinc-lead-silver concentrate will be produced from a simple flowsheet. This flowsheet has been developed in the laboratory and demonstrated during an extensive pilot plant campaign. A single stage SAG mill will be utilised to grind the ore down to a P80 = 45 ltm (80 per cent of particles passing 45 ¦rn. Conventional flotation cells will produce a single rougher concentrate that will be reground to No

Jan 1, 1993

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

By M B. Lovitt

At present there exist few engineering calculations and principles to determine exclusion zones for personnel in the vicinity of underground explosive storage areas. This paper is written to encourage discussion and proposes a method to determine the impact of a blast wave through scientific principles. Then, criteria to determine an ‘exclusion zone’ need to be identified.There has been much work on identifying the pressure rise and the energy of explosive detonations underground but little to develop standards in criteria that can be used to identify exclusion zones for useful design of underground infrastructure. The author presents the newest ways of calculating the pressure rise and energy (impulse) of detonations and puts forward some criteria to be used in the identification of personnel exclusion zones to spark peer review and discussion of these criteria towards developing standards for engineering design.Smith and Sapko (2005) used Sach’s scaling laws to develop a relationship for both pressure rise and impulse, which incorporated factors for intersections. Intersections will have a large bearing on the peak pressure and the energy of the blast wave and needs to be incorporated. Silvestrini, Genova and Leon Trujillo (2009) developed the scaling laws with an energy concentration factor to predict blast propagation in partially confined geometries and together the author has proposed equations for determining the peak side pressure and the impulse in a tunnel. Given the weight and type of the explosive, the average cross-section of the tunnel complex and the number and type of intersections encountered, the pressure and impulse can be calculated.The military has carried out many investigations as to the influence of blast pressure and impulse on the human body. Lung damage, ear damage and velocity knock down are three of the criteria standards that are presented as possible methods of determining exclusion zones around an underground explosives magazine. The author suggests that the velocity curves presented by Bowen, Fletcher and Richmond (1968) could be an acceptable method of determining an exclusion zone as it incorporates the side pressure and the energy of a blast wave to determine the ability of the wave to knock down personnel.CITATION:Lovitt, M B, 2014. Exclusion zone calculation for underground explosives storage, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Young DJ

Gold mineralisation at the Hamata prospect is related to a series of stacked pyrite and quartz-pyrite veins associated with a number of shears which strike N to NE and dip E. Mineralisation is contained entirely within the Morobe Granodiorite close to the intersection of the Upper Watut Fault and some younger NE to SW striking faults. The prospect was originally detected in 1987 by a regional stream sediment sampling programme. Subsequent mapping and sampling outlined an anomalous zone approximately 900m long by 300m wide. Drill testing has indicated a resource of 46Mt at 0.9 g/t Au.

Jan 1, 1991

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006

By Hall G

The Mount Isa silver-lead-,zinc deposit possesses a number of features which sets it apart from usual occurrences of ores containing those metals. The deposit has been described in vario:us papers, but development upon deeper levels during the past two years has, yielded much information not hitherto published. Purpose of the present paper is to furnish a unified and coherent perspective by tracing briefly the full rock deformational and mineralization processes responsible for the ore deposition. The paper represents the outcome of ten years' organized geological effort at Mount Isa. Information contained in it supersedes that previously published.A bibliography of published articles relating to Mount Isa ore deposition is appended. In preparing the present paper previously published data have been drawn upon freely wherever applicable. The authors are especially indebted to the papers by Grondijs and Schouten, and by O'Malley and McGhie, which present results of systematic microscope studies of thin and polished sections from comprehensive suites of Mount Isa ore.

Jan 1, 1942

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021