Search Documents

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By C. E. Lesher

Two processes for agglomerating fine sized ores with low temperature coke are described. One process (Orcarb) agglomerates ores with limited amounts of carbon; the other (ore-carbon pellets) pelletizes fine sized ores, using low temperature cokes as the binder. Data are presented on the products obtained when taconite, magnetite, and hematite concentrates and several titanium oxide ores were used. REDUCTION of finely divided oxide ores has long been a major metallurgical problem. Various methods of agglomerating, notably briquetting, sintering, nodulizing, and pelletizing, have been developed and are in industrial use. Carbon is the usual reducing agent for oxide ores and attempts have been made to agglomerate fine ores with coking coal in order to get the metallurgical advantages of intimate contact and increased particle sizes suitable for subsequent smelting or reduction.1-3 For the past three years, research has been in progress on two processes for combining fine sized ores with reactive carbon in the form of low temperature coke. By one process, designated Orcarb, the ore is coated with coke carbon in amounts limited to that required for reduction and the result is an appreciable but limited increase in product particle size over that of the original ore. The second process, called ore-carbon pellets, produces pellets of fine ore bound by low temperature coke. The first objective was to develop a process for combining an oxide ore with only enough carbon for its reduction, the amount being that derived from the simple reduction equations. The carbon (that amount theoretically required for the reduction of the oxides in an agglomerate with ore), calculated to CO, ranges from 10 pct for zinc calcines or phosphate ores to 21 pct for rutile and 26 pct for silica. The carbon required for reducing iron oxides falls between the extremes—10 and 26 pct. When the carbon in the agglomerate is low temperature coke, reduction by hydrogen may be expected to take place, thus modifying the calculated carbon require- ment. On the other hand, in practice, an excess of reducing agent over that required in theory is normally used. Screen sizes of three iron ores on which the greater part of the experimental work was performed are given in Table I. Most of the testing was done with Freeport (Renton Mine) coal, but Pittsburgh and Elkhorn bed coals were also used. The first objective was to agglomerate the ore with sufficient low temperature coke to provide carbon for reduction, i.e., in the range from 10 to 25 pct. This was accomplished by preheating the ore, mixing with pulverized coking coal, and completing the coal carbonization in a plain steel rotating retort. The pilot retort, as it is now constituted, is shown by diagram in Fig. 1 and photograph, Fig. 2. Ore is fed into the upper kiln by a screw; it is heated to 900" to 1100°F by direct flame and it is then discharged into an insulating hopper from which it goes

Jan 1, 1956

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By AIME AIME

To accompanying photograph of the plant of the Beattie Gold Miner Limited, at Duparquet,. Quebec, is taken from the east and shows the open-pit from which the ore is taken during the summer. The buildings on the level ground above the open-pit are the change rooms, steel shop hoist building, compressor building, machine shop, warehouse, carpenter shop, and oil house. The main five-compartment shaft is shown west of the hoist building. The crusher plant adjoins the headframe and a long conveyor transports the fine ore

Jan 1, 1936

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

By C. M. WEILD

ATTENTION has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bay. Here the Spanish-American Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore; and the necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city, and at Taco bay and Navas, points lying a few miles west of Baracoa. The area of the Cubitas deposit is said to be 6,000 acres, and the yield of ore is estimated at 150,000,000 tons. The Baracoa. deposits are less well known, but preliminary estimates have placed their joint ore-reserves at 40,000,000 tons. Accepting the above tonnages as reasonably correct, we conclude that the deposits enumerated give promise of adding about 1,000,000,000 tons of iron-ore to the world's supply; they have, therefore, to be considered in any attempt to fore-

Aug 1, 1909

By W. C. Hagel, J. H. Westbrook

Usittg a sectioning technique with Agl10 as the tracer, the diffusion of silver in silver-excess (45.8 at. pct Mg), near-stoichiometric (49.8 at. pct Mg), and magnesium-excess (52.0 at. pct Mg) cylinders of CsCl-type AgMg was determined from 500" to 700°C. Diffusion coefficients conform to the expression D = Do exp (-q/RT) where the respective Do values are 1.53, 0.280, and 0.134 sq cm sec-I and the Q values are 41.3, 40.6, and 38.0 kcal g-atom-'. Lnttice-parameter and density measurements were performed on a more numerous assortment and wider range of compositions. Substitutional defects were found on both sides of stoichiometry. Activation energies for other rate processes in these alloys show related trends with changing composition, although silver may not be the rate-detemining species. KNOWLEDGE of diffusion coefficients is necessary for a quantitative understanding of the many rate processes (e.g., grain growth, precipitation, sintering, oxidation, or mechanical deformation) occurring in solids. Although these data are available for most metals and common alloys, they are quite limited for intermetallic compounds—a group of materials whose unique physical and mechanical properties are presently attracting great interest. From a fundamental viewpoint, diffusion in intermetallic compounds also offers several engaging aspects owing to: their ordering, the possibility of introducing large, stable concentrations of lattice defects, and the variety of bonding types and crystal structures which can be found. In the case of CsC1-type compounds, some previous work has been directed at examining the role of vacancy defects by changing their concentration compositionally. The diffusion of Co60 was measured in 0 NiAl1- and in P COA., Except for the results of Smoluchowski and Burgess, isothermal diffusion coefficients were found to pass through a minimum at the stoichiometric composi- they decreased sharply on what was reported by Bradley and co-wrkers' to be the vacancy-rich (aluminum excess) side of stoichiometry. This investigation of the diffusion of Agl110 in AgMg was undertaken both as an adjunct to a concurrent study of its deformation behavior and for the purpose of obtaining information on the influence of lattice defects and temperature on diffusion in another CsC1-type intermetallic compound. Bcc AgMg remains ordered up to and melts congruently at 820°C. Solubility limits at 300°C are about 41 at. pct Mg and 53 at. pct Mg. It is one of the Hume-Rothery electron compounds with a 3/2 electron-atom ratio. Previous investigations of its properties include hardress,' tenile,'-' electrical reistivity, and thermodyna-mic1',14 studies. Indications of a high bonding strength may be found in the large heat of mixing1' and in the 6-pct vol contraction on compound formaticp, as calculated using atomic radii of l.40 and l.55a for Ag and Mg. EXPERIMENTAL PROCEDURE Alloys were prepared by the induction melting of selected fine silver (99.95) and low-iron magnesium (99.95) in magnesia crucibles under 1 atm of A. Supplied by the Handy and Harmon and Dow Chemical Cos., respectivelv. Melts were poured under argon into graphite molds providing 1 1/8-in.-diarn. by 4-in.-long ingots. These were homogenized in evacuated and argon-filled fused-silica capsules by heating for 16 hr at 750'. Three 1 in.-diam. by 3/4-in.-long cylinders were machined from the mid-portion of each ingot for diffusion measurements. Three alloys, analyzing 45.8, 49.8, and 52.0 at. pct Mg were taken as representing the extremes of interest, with 49.8 at. pct Mg being very close to the stoichiometric composition of 50.0 at. pct Mg.

Jan 1, 1962

By F. J. Plecity, J. T. Michalak, W. C. Leslie

Isothermal recrystallization and grain growth in zone- and vacuum-melted irons and Fe-Mn alloys, up to 0.60 pct Mn, were studied in the range 480° to 650° C, after 60 pct cold reduction. In initial stages, rate of grain growth and rate of recrystallization of iron decrease with time. The recrystallization is typical of a growth-controlled process, and rate of growth is determined by the extent of recovery. Mn decreases rates of growth and of recrystallizatzon. The recrystallization process changes at about 0.30 pct Mn and nucleation may become time-depetzdet~t. In recent years, considerable effort has been expended in determining the effects of solute elements on recrystallization and boundary migration in fcc metals. The results have indicated that the effects produced by single solute additions are dependent upon both the element added and its concentration.'-' In contrast, there have been very few attempts to determine the characteristics of recrystallization and boundary migration in high-purity bcc metals, especially after heavy deformation, and the effects thereon of single solute elements.9-11 This study was undertaken to determine the recrystallization characteristics of various "high-purity" irons and the effects of manganese additions at two levels of base purity. It was hoped that the information obtained would improve our understanding of the recrystallization of pure metals and aid in formulating a theory for the effect of solute elements. The interest was not entirely academic, for the annealing of low-carbon steels, which is of very great commercial importance, is but poorly understood. MATERIALS The compositions of the irons and iron-manganese alloys used are listed in Table I. The zone-melted iron and Fe-Mn alloys were made by Battelle Memorial Institute. Iron S-1 was arc-melted in a water-cooled steel mold in an argon atmosphere. The ingot was forged into a bar, then given two horizontal zone-refining passes in an alumina boat. Iron V-4 was treated in a similar manner, but was not zone-refined. The iron for the zone-melted Fe-Mn alloys was induction melted in vacuum in MgO crucibles and cast into alumina molds. The ingots were forged into bars, machined to shape, and a groove milled down one side of each. The best available electrolytic Mn was placed in the grooves, and the bars were zone melted. The vacuum-melted Fe-Mn alloys were induction melted in this Laboratory in MgO crucibles and poured into cast-iron molds. Iron V-5 was purchased from National Research Corp. in the form of a small vacuum-cast ingot. The low-carbon steel was made by induction melting in air at the U.S. Steel Corp. Applied Research Laboratory. The history of the materials prior to the final cold reduction differed; these details are given in the Appendix. The penultimate grain size of the principal materials was kept in the range ASTM 2 to 4, except for the low-carbon steel. PROCEDURES The cold work prior to the final recrystallization anneal was kept constant at 60 pct. It is known that rolling procedure can influence the kinetics of recrystallization of ironI2; therefore, all specimens were rolled in one direction only, between clean,

Jan 1, 1962

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By Gordon B. Brox, Joseph F. Mcaleer, Charles C. Goddard, Edward P. Shea, Robert G. Ingersoll, Lester G. Zeihen, George J. Burns, John M. Guilbert, Richard N. Miller, Charles Meyer

The Boulder batholith is a composite intrusive in which the Butte quartz monzonite is the dominant rock type. Quartz porphyry dikes intruded the quartz monzonite in directions which were subsequently followed by the eastwest- striking Anaconda system of veins, the earliest major veins in the district. Anaconda veins are faulted by northwest-striking veins of the Blue system, which are most prominent in the central third of the district. Anaconda veins are the major producers in the western third of the district and also in the eastern third, where the "horsetail" zones break off from them. Individual oreshoots are thousands of feet long as well as deep on both systems of veins, but they are generally more persistent and thicker on the Anaconda veins. Viewed broadly, the mineralization in the big veins is arranged in crudely concentric zones of zinc and manganese around a central zone of copper. Only slightly offset from these zones, but earlier structurally, is a zone in which quartz-molybdenite veinlets are prominent. This zone tops at about the 2800 level and widens downward. The pattern of distribution of Cu-Fe-S series minerals in the large veins of the copper zone is not symmetrical with respect to the metal zones. There is a fringe of chalcopyrite-bornite all around the copper front. However, within the copper zone, pyrite-chalcocite-enargitecovellite- digenite assemblages are prevalent near its eastern edge from the 3800 level to the surface, whereas deep on the large Anaconda veins in the western part of the copper zone, chalcopyrite is dominant. Here the chalcopyrite grades upward into bornite-chalcocite ores and eastward into the high-sulfur assemblages of the Leonard mine. Sericite-biotite-K-feldspar alteration envelopes, containing up to about 2 per cent copper as chalcopyrite, are present on some of the quartz-molybdenite veinlets at deep mine levels in the molybdenite zone. These envelopes contrast sharply mineralogically and chemically with the later sericitic and argillic alteration envelopes around Main Stage veins. K'0-Ar'0 ratios indicate that they may be older by about 4 m.y. Secondarily enriched copper ores are mined in the Berkeley pit in the southeastern part of the district. At the present time they account for about half of Butte's production of copper.

Jan 1, 1968

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

By ALBERT F. J. BOARDEAUX

(Canal Zone Meeting, November. 191(j.) I. GENERAL INTRODUCTION. 1. Historical. ALLUVIAL gold was first discovered in Guiana in 1852, in the sands of the Arataye river; by Paulino, a Brazilian convict. During the following years, gold was found also in the rivers Orapu, Cirubé, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Tat, and Couriége. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysée, Pas-Trop-Tot, date from 1878, and their production has been about $5,000,000. In 1888, the Awa placers, along the boundary between the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company,, the Dutch Guiana French Mining Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have pro-duced about $18,000,000 in six years (1894-1900), but not even one-fourth of the production went through French Guiana and

Nov 1, 1910

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By James Douglas

Once—and fortunately only once—before this occasion, was it my sad duty to express the loss we had sustained in the death of an eminent member. Dr. T. Sterry Hunt* was a student of chemistry who, by his investigations into the properties of the elementary bodies, had assisted emineiltly in the progress of the technical arts, and, more than any American of his generation, had helped to lay the foundations of chemical geology. William Earl Dodge, whose death we deplore to-day, occupied a rank not les~ importaiit in the army of industrial workers

Jan 1, 1904

By W. S. CAYPLESS, H. O. Hofman, E. E. HARRINGTON

I. INTRODUCTION. LIME-ROASTING is a term proposed by Ingalls 1 for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If, finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse undecomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale, the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the .bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1907

SME Membership Directory Listings of record March 31, 1072 SOCIETY OF MINING ENGINEERS OF AIME

Jan 7, 1972

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

PROF RICHARD ÅKERMAN Stockholm, Sweden PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France ALEXANDRE POURCEL Paris, France JOHN E. STEAD Middlesborugh, England DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JAMES M. SWANK (Associate) Philadelphia, Pa. PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1917