Search Documents

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

The recent boom in the mining industry has lead to some unique challenges in successfully operating processing plants. With high turn-over rates of both operators and technical staff, and many experienced personnel leaving regional sites for city based jobs there is often an onsite knowledge vacuum and this in turn puts pressure on both site training departments and senior metallurgists to provide the relevant skills to the continuous stream of new staff. Frequently both operators and new metallurgists are instructed on a æhow-toÆ basis rather than giving them the understanding as to why tasks are performed and decisions are made. This paper has been written with the plant operator and metallurgist in mind and aims to provide suitable material to be incorporated into a site training manual. Topics have been broadly divided into the following categories: factors that operational staff can control; including pulp density, air addition rate, froth depth, particle size and reagent type and use; factors that operational staff cannot control; providing general information on bubble size, froth stability, pulp chemistry and the mechanical effects of the rotor/stator system; and process improvements. Each topic is discussed with a view to clarifying the key process variables that need to be understood and optimised in an industrial operating plant.

Jan 1, 2009

Start with your assessment of the minerals business —domestic mining as well as operational and consulting perspectives. As a third generation miner, I have been living the mining business for as long as I can remember. I have watched commodity prices produce boom and bust cycles in places like Price, Utah (coal), Douglas, Arizona (copper) and Eureka, Nevada (gold). It is unsettling to see how our industry has fluctuated, but it always seems to rebound if you can stick out the down cycles. However, our most recent dip in the cycle was, in my opinion, characteristically and permanently different. In the past, when prices went south, people hunkered down and waited out the cycle until things came back, much the same as they had every other time. Not this time. This time, we saw a consolidation of the industry in proportions never seen before. Mega-mergers like Exxon-Mobil, Phelps Dodge-Cyprus and Newmont-Normandy have changed the complexion of our industry forever. And that is true not just of the mining companies; it happened across the supporting business lines as well. As a midsized niche engineering and environmental service provider to the mining industry, companies like mine are few and far between these days. The lean cycle saw many of the small and midsized providers get gobbled up by consulting giants like URS and TetraTech. The mentality of a mega-company, whether a commodity producer or a goods or service provider, is different than that of their small- and medium-sized counterparts.

Jan 1, 2005

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By H. B. Hill

The Salt Flat field, formerly called the Toe -Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately 111. 20 to 45° E. The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1928, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting. The total oil production for the Salt Flat field to and including September, 1930, was 19,833,215 barrels. The most reliable figures available of water production were compiled for a number of leases and wells in the south half of the field. These data show that the water percentage for the average well in this part of the field increased steadily from 30 per cent for January, 1929, to 81 per cent for December, 1929. The estimated daily water production of the entire field for December, 1929, was about 82,000 barrels as compared with a daily oil production of 29,725 barrels; or approximately 2.7 barrels of water were produced with each barrel of oil 14 months after the discovery well was completed in the Edwards pay. Estimates of water production in the (Old) Luling field, which is near the Salt Flat field, place the daily water production at about 150,000 barrels (July, 1929) as compared with a daily oil production of 11,000 barrels. These figures indicate that in the Luling field approximately 14 barrels of water must be lifted for each barrel of oil produced. The Luling field was discovered in August, 1922, and a peak annual production of 10,210,000 barrels was reached during 1924. The production during 1928 was 5,057,000 barrels of oil from an average of 567 producing wells for the year. Although water appeared early in the life of the Luling field, the oil production has been well sustained. Another feature of outstanding interest is the comparatively few producing wells that have been abandoned on account of water during the soven years of operation of this field. Comparison of data between the Luling and Salt Flat fields is of importance because of the nearness of the two fields. The Luling field is a narrow strip or "shoestring" approximately 8 miles long, with a maximum width of 3,400 feet. Production is obtained in the Edwards limestone at an average depth of 2,200 feet on the upthrow side of a fault. Similar conditions of accumulation are found in the Salt Flat field at greater depth to Salt Flat field as outlined (April, 1930) is about 7 miles long? with a maximum width of 2,000 feet. At the time the field work was begun (July, 1929) in the Salt Flat field, drilling operations had been almost completed in the south half of the field, while the north half was still under development. Cross sections and a structure contour map interpret the subsurface conditions in the south half of the field, where the water conditions first became serious.

Jan 1, 1931

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use, in a helicopter. Tests showed that EM signals from lightweight (3/4 lb) transmitters could be detected both on the surface and from a helicopter through as much as 4450 ft of relatively high conductivity (2 X 10- 2 mhos/m) overburden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 1, 1973

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Major mechanical components in the hoist and mechanical drive train are considered. Design and specification criteria based on American standards and practices are developed as they apply to typical mine hoist arrangements.

Jan 1, 1988

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011