Search Documents

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By L. du Plessis

The name FISH (Fully Integrated Sort House) refers to a class of technology deployed at Jwaneng Mine final diamond recovery. The FISH concept is based on three pillars, namely: ?Improved sorting efficiency FISH is based on laser technology, which is more efficient than hand sorting for certain product categories. Laser sorting is based on measuring in-elastically scattered light from molecules and this is referred to as Raman spectroscopy. The Raman scattered light occurs at wavelengths that are shifted from the incident light by the energies of molecular vibrations ?Availability of production information Roller gap diamond size distribution information is generated on line for upstream process optimization ?Improved product security A ?hands-off? philosophy reduces security risk during operation and maintenance of the plant. In addition, a number of lessons were learnt about the application of new technologies in the industry: ?The required human competency profile demanded by new technology should match the available competencies of the operational staff ?An integrated information management system should be fully functional for both production management and diamond control purposes ?Operational feedback must be correctly evaluated to identify design, maintenance, training and operational issues so as to accelerate the maturity of the new technology within the time span of the sustainable operations project ?Project execution and technology maturity risks have to be evaluated and married to ensure risk mitigation by means of suitable project resource and contracting model selection.

Jan 1, 2003

By Mario A. Terceros H., K. Rainer Massarsch

"ABSTRACTThe Expander Body (EB) technology has been used successfully to increase the pile toe capacity of bored piles in loose to medium dense soil. An important advantage of the EB system is the ability to monitor the EB expansion process, which provides important information regarding soil strength and soil stiffness. This information, obtained for each installed pile, can be used to determine the actual shape and pile toe area. The expansion pressure can be used to design the pile base capacity.The Expander Body system has been recently improved by incorporating the possibility of post-grouting of the soil below the expanded pile toe. This improvement measure provides additional strength and stiffness to the pile toe and reduces pile settlement.The shaft bearing capacity of bored piles can be increased by using a soil displacement auger, which avoids soil decompression and increases lateral soil stress. This paper describes the principle of the EB system. During the past 20 years, a large number of EB piles have been installed in Bolivia and elsewhere, providing a sound database. Results from field loading tests are presented. A comprehensive study of test piles with and without EB base has been carried out which demonstrates the improvement effects that can be achieved by the EB pile system and the combination with the displacement auger pile method. A design concept for the EB pile system with the full displacement auger pile is presented. A high degree of quality control can be achieved by monitoring the entire pile installation process, including the displacement pile and the Expander Body.1. IntroductionIn many regions of South America, soil deposits consist often of predominantly loose to medium dense sands and silts, often with high groundwater table. In the Santa Cruz area in central Bolivia, such soils are frequently quaternary sediments, deposited by the river Piray. The city of Santa Cruz is located at the right bank of the river.The most common deep foundation method during the last 30 years has been cast in situ piles, augered and concreted under support of bentonite slurry. The design of such piles has been based on SPT results. However, SPT is often performed without quality control and the reliability of geotechnical data is therefore often poor. Traditional methods of pile installation with simple well drilling equipment of insufficient capacity are frequently used. Such methods lack basic requirements of quality control. Such piles have usually low toe resistance and work mainly by shaft resistance . Although the construction process and materials are cheap, the final product has variable and limited capacity. However, the most serious deficiency is that actually achieved pile capacity and pile settlement can be erratic and difficult to predict, leading to uncertainties with regard to actual foundation performance."

Jan 1, 2014

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By L Langer, R Simcock, M Davis

Rehabilitation of mining sites helps to achieve the purpose 5(2c) of The Resource Management Act 1991 û æavoiding, remedying, or mitigating any adverse effects of activities on the environmentÆ. The environmental outcomes for recent and current mining operations on the West Coast are variable. There are some exemplary mining operations which are restoring or even improving land use and environmental factors in the region, particularly those operated by the larger mining companies. There are also examples of an exploitative mentality where the environment and land have been severely degraded by mining activities. Technology has been developed to prevent a repetition of the historical destruction of the environment through mining. Failure to rehabilitate mined land is no longer acceptable to the New Zealand public in the 1990s and damages the credibility of the mining industry. Examples of successful mine site rehabilitation to pastoral farming and to production or plantation forestry are illustrated from the alluvial gold mining industry. Planning, sequencing of operations, the utilization of sailor plant growth materials, and aftercare are key factors in successful land rehabilitation to these productive uses. There is also a recent focus on restoring indigenous forests and wetlands at both coal and gold mining sites, particularly for mines on or adjacent to the conservation estate. The results of scientific research and efforts by the industry on techniques for rehabilitating rainforest and pakihi wetland after mining are presented, particularly from the Giles Creek Dunoille Coal Mine. There is a need for further research and trials to apply and extend rehabilitation techniques to other geological and environmental situations, particularly to mines in mountainous areas and to difficult environments like the coal measures ecosystems of the plateaux above Westport.

Jan 1, 1996

By F. Enslin

Heavy metals and sulphates in acid mine drainage (AMD) can beadsorbed onto bentonite clay, leaving clean water and a heavy metal loaded clay precipitate as products. Due to the toxicity of heavy metals, the clay could not be disposed of safely in the past. A method was thus required to remove the heavy metal content from the clay. Acid leaching was proposed to liberate the heavy metals from the loaded clay. Sulphuric, nitric and hydrochloric acid were considered as lixiviants. Loaded clay samples were leached over a range of pH values from 1 to 3.5 to identify an optimum leaching condition. From the results it was found that metals can berecovered from loaded bentonite clay by means of acid leaching and the optimum pH for heavy metal liberation was found to be 2.5, with uranium as an exception, being optimally leached at a pH of 3. This allows for the possibility of selective leaching. Furthermore, X-ray diffraction analyses indicated that the clay structure did not deteriorate significantly during acid leaching, suggesting that the bentonite could be reused. The treatment of AMD with bentonite clay, and subsequent acid leaching of the clay, is a sustainable solution, and current outcomes could possibly lead to industrial implementation of the process during water purifying and metal recovery from waste streams. Keywords: Acid mine drainage, bentonite, heavy metals.

Jan 1, 2010

By M Stewart

In January 1994, Macraes Mining Company started a new phase of exploration to find additional resources along strike and down dip of identified resources for a mill that was being expanded from 2.1 Mtpa to 3.2 Mtpa. At 30th June 1997 a total of 456,784 m in 3,627 holes had been drilled at the Macraes Gold Project with approximately 325,000 m in 2,100 holes drilled in the latest phase of exploration. This necessitated the construction of resource estimates on a more frequent basis and resulted in the formation of a resource modelling team, assisted by Snowden of Perth. Since April 1995, 14 separate resource estimates have been completed. At Macraes, resource estimates are built using Medsystem/Minesight software. The geological interpretation is converted into a set of three dimensional wireframed solid models which are used to code drillhole composites and blocks in a block model. The interpolation method of indicator kriging is used to interpolate grade into the blocks. Classification into measured, indicated and inferred categories is on the basis of geological confidence and drill spacing. The resource estimate is reconciled against grade control polygonal estimates on a bench by bench basis and on a monthly basis. Grade control estimates are reconciled monthly to mill production. For the period 30 June 1995 to 30 June 1997, the resource estimates have under predicted tonnes by 4% and grade by 1% to under predict ounces by 5% at a 0.5g/t cut off. At ROM sulphide cutoff grade, the models have over predicted tonnes by 5%, under predicted grade by 5% to over predict ounces by 1%.

Jan 1, 1997

The principles of geometry and trigonometry are so continuously used by mining engineers for the purpose of accurately and intelligibly recording their measurements, that the writer is prompted to lay the following cursory remarks upon mine surveying before the members of this Institution in the hope of eliciting a free interchange of opinion upon details of this interesting branch of the profession. He proposes to deal with surveying only so far as it concerns the mining engineer, not to intrude upon the domain of the professional surveyor, and, in this instance, to discuss more especially that which may be termed the mechanical, rather than the mathematical side of surveying.In the latter part of the eighteenth century and the beginning of the present one, the usual underground surveying equipment in the English metalliferous mines, consisted of a magnetic needle in a fiat square wooden box of about 9-inch sides, a two-foot rule, a long cord, aud a stool, upon which to place the needle and box. The operator took his bearing by sending his assistant with the end of the cord as far in a straight line as the length of the cord would admit.On its being drawn that he held its end in one hand and placed the side of the compass-box against it with the other, and noted the bearing thus found either by a book entry, or by ticking it off with a piece of chalk on the board the compass lay in. He then measured the cord with a two-foot rule. It is needles to say that with these appliances the accuracy of the results were open to question, and mining surveying was not unduly popular.In the present day, engineers have the advantage of using instruments brought to such a state of perfection, and of employing such an exact system of underground surveying, that inaccurate work must usually be attributed either to lack of care, or lack of ability in the operator.

By N. Kuyucak

"Acid mine drainage (AMD) is one of the most significant environmental challenges facing the mining industry worldwide. It occurs as a result of natural oxidation of sulphide minerals contained in mining wastes at operating and closed/decommissioned mine sites. AMD may adversely impact the surface water and groundwater quality and land use due to its typical low pH, high acidity and elevated concentrations of metals and sulphate content. Once it develops at a mine, its control can be difficult and expensive. If generation of AMD cannot be prevented, it must be collected and treated. Treatment of AMD usually costs more than control of AMD and may be required for many years after mining activities have ceased. Therefore, application of appropriate control methods to the site at the early stage of the mining would be beneficial.Although prevention of AMD is the most desirable option, a cost-effective prevention method is not yet available. The most effective method of control is to minimize penetration of air and water through the waste pile using a cover, either wet (water) or dry (soil), which is placed over the waste pile. Despite their high cost, these covers cannot always completely stop the oxidation process and generation of AMD. Application of more than one option might be required.Early diagnosis of the problem, identification of appropriate prevention/control measures and implementation of these methods to the site would reduce the potential risk of AMD generation. AMD prevention/control measures broadly include use of covers, control of the source, migration of AMD, and treatment. This paper provides an overview of AMD prevention and control options applicable for developing, operating and decommissioned mines."

Jan 1, 2002

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

By Roberto Maldonado

El presente texto señala el proyecto de profundización en la mina Animón considerando sus características como: geología e hidrogeología, parámetros geomecánicos, niveles de producción, costos de capital y operación, eficiencia del sistema, flexibilidad para cambios en las operaciones, reservas de mineral y consistencia con el sistema de explotación. De forma que a través del conocimiento de estas y de las herramientas gráficas tridimensionales, se pueda analizar las diferentes alternativas, incluyendo condiciones que debe cumplir el proyecto de profundización, el cual abarca también los servicios auxiliares y ventilación.

Sep 12, 2005

By Daryl E. Radcliffe, Raymond M. Stateham

The Bureau of Mines, under a Cooperative Agreement with the Bear Coal Company, Somerset, Colorado, conducted a large scale evaluation of the effect of time lapse on roof stability. Time lapse in this study is the interval between exposure and permanent support of the mine roof. The study indicates that time lapse is not a critical factor in roof stability provided permanent support is installed before catastrophic failure begins. Concurrently with the time lapse study, investigations were made of stress distribution around resin-grouted bolts, the regional stress field, and anomalous geologic conditions. The behavior of the resin-grouted bolts, at least in the Bear mine, appears to fit the Coulomb-Navier Theory. Geologic conditions are primary factors in trends of roof stability that extend across the mine.

Jan 1, 1982

By C J. Hogan

Increasing demand for fine grinding to improve mineral liberation and metal recovery and the need for stricter control of the environmental impact of tailings deposition poses problems for tailings disposal. This has led to an increasing number of investigations of properties of tailings and their disposal. This paper describes laboratory model testing undertaken on Macraes mine flotation tailings to provide information on tailings behaviour under conditions of subaerial deposition. The in-place density or 'dry density' of the impounded tailings and the impoundment depth relationship are important for utilisation of the available impoundment storage facility and results of dry density to depth relationships are given for the Macraes mine tailings impoundment.

Jan 1, 1993

By G B. Arehart

The Midas epithermal system is one of the larger low-sulfidation epithermal vein systems discovered in the western US in recent years, containing in excess of 3 Moz of gold (premining). The deposit is spatially and temporally related to bimodal volcanism in the Northern Nevada Rift; dates on igneous rocks (16 - 14.7 Ma) bracket the age of high grade veins (15.3 Ma). Hydrothermal alteration at Midas is typical of epithermal systems, comprising proximal potassic through distal propylitic assemblages; in contrast to many epithermal systems, Midas has minimal development of wallrock illite/sericite. Mineral assemblages are clearly zoned on the vein structures that acted as focal planes for fluid upflow. Geochemical zoning patterns also show this zoning. Metals were deposited in open-space veins as the result of boiling of hydrothermal fluids; multiple episodes of crustiform mineral deposition are documented in the vein textures. The major vein minerals include quartz, adularia, calcite, selenides and sulfides, with electrum as the primary ore mineral. REE patterns for vein material are similar to patterns for coeval rhyolites, but distinctly different from patterns of the host rocks. Stable isotope data are consistent with meteoric water as the dominant ore fluid. Combined REE and stable isotope data suggest that fluid from which the main ore-bearing stage of the veins was deposited was slightly lower pH than other stages.

Jan 1, 2005