Search Documents

By David Weidner

Public relations, regulatory compliance, determination and implementation of pre-blast inspections, and accurate blast monitoring data are all essential components when conducting blasting operations for a large scale, high profile, urban site development. By working closely with the contractor, an independent vibration consulting firm can provide the commitment of time, energy and resources to tie all of these elements together. When this comprehensive approach is properly implemented, problems often associated with projects of this magnitude can be almost completely eliminated.

Jan 1, 2001

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By K Ringwood, J Cummings, C J. Moran

The development of a water accounting framework that enables consistent and contextual reporting of minerals operationsÆ water use, represents a key sustainable development objective that many Australian minerals companies have committed to. A future water accounting framework will require: key terms and definitions for water metrics for use in the Australian minerals industry that are consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current regulatory requirements and voluntary approaches were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (eg water loss through evaporation). The adopted terms and definitions typically require a combination of empirical and estimated data. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites, selected to test a variety of commodity and biophysical situations. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and following a period of stakeholder engagement and third party review, is being refined as a first step towards developing nationally consistent water use reporting for the Australian minerals industry.

Jan 1, 2009

Grinding and Flowing Investigation on Dry Stirred Ball Milling in Order to Determine the Influence of Grinding Aids Huge difficulties of the great ultra fine ground material production in dry stirred ball mill are the cohesion and agglomeration of the particles. During grinding the material stick on the grinding wall and the grinding media furthermore the grinds start cohere, making aggregation and agglomeration to appear. Due to these effects the particle size will not decrease after a certain value during grinding and the energy demand increases significantly. According to experience on fine grinding in ball mill, it is well known that these effects can be reduced with the use of grinding aids. The influence of grinding aids has three different effects: due to the adsorption strength reduction (Rebinder effect) the grinding resistance of the material decreases; the surface energy diminishes and the agglomeration liability decreases; and the flow properties of material improve. The aim of this study is to investigate the flow properties of fine grinds and the effect of grinding aids on flow properties in case of dry stirred ball milling. In addition, the influence of grinding aids was investigated based on the particle size distribution and specific surface area of grinds and the specific energy demand of grinding. The examinations were carried out with three different model materials (limestone, clinker, quartz) using the usually applied grinding aid. The flow properties were measured by the Jenike shear cell; the particle size distribution and specific surface area were measured by laser particle size analyser (Fritsch Analysette 22), grinding energy demand was measured with microcomputer controlled digital energy meter. It can be said that under certain measuring circumstances the influence of grinding aid on flow properties can be demonstrated by Jenike shear cell, so the grinding result is in correlation with the flow properties of grind.

Sep 13, 2010

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

IN concentrating mills, where several millerals are recovered for realisation in more than one product, various systems are used to express the relative economic value of the work done, and, in the hope that it may prove of use to other operators, the writer will describe a system which, in his opinion, is more complete than any other that he has seen published.The controlling factor in all mill work must be based on the economic result represented by the greatest margin possible between the realizable value of the products and the cost of obtaining same.From a mill-man's point of view these are affected by the following factors:1. Metal contents of ore.2. Grade of products.3. Recoveries.4. Working costs.The grade of ore milled is usually outside the mill-man's control, but this may exercise a considerable influence on the grade of his products, metal recoveries, and revenue per ton of ore. Higher grades or recoveries may be obtained by using a more expensive process, or by additional grinding or reagents, and the economic comparison can only be arrived at by obtaining an analysis showing the monetary value of each variation within the possible limits.In the system to be described, the value of unit variations of metal contents of the ore, grade of products and recoveries are calculated in terms of a monetary unit per ton of ore with the returning charges ruling, and any suitable metal prices. To do this it is necessary to assume what, for convenience, is termed a "standard" set of results from the mill, preferably representing about average conditions, and having calculated the effect of unit...

Jan 1, 1931

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

Fine Coal Evaluation by Gravity Methods

Sep 13, 2010

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

By B. J. Moore

This publication contains analyses and related source data for 352 natural gas samples from wells and pipelines in 18 States and 5 foreign countries. All of the samples were obtained and analyzed during calendar year 1974 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economics. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Sixteen previous publications have presented the results of 10,479 gas analyses prior to 1974. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on

Jan 1, 1975

By Peter Grundy

La eficiencia de los recursos en los procesos transparentes de gestión de las empresas permite aumentar el valor de los accionistas. En ese sentido, el presente texto señala el uso de la RCM como estrategia en el funcionamiento de un equipo que se centra en la confiabilidad. RCM es un proceso lógico que involucra aspectos técnicos y de negocio, capaz de producir resultados a muy corto plazo. Este proceso concluye con una recopilación de documentos fiables y totalmente óptimos para el desarrollo de las funciones de mantenimiento. Su uso correcto en la evaluación de los requisitos de mantenimiento de los equipos existentes, genera un mantenimiento menos costoso, confiable y eficaz. Asimismo se disminuye los costos de mantenimiento y se relaciona los aspectos ambientales y de seguridad.

Jul 17, 2000

By Mervin D. Marshall

A quick-reaction, mine permissible rescue vehicle (MERV) was developed for use by rescue teams. The MERV is a 6-wheeled, battery-powered unit with life support equipment and instrumentation; designed for a two-man team, with provisions for handling two victims or tools in a trailer. The vehicle is 100 inches long, 56 inches wide, and maximum height of 34 inches. It can be lowered down most mine shafts and has clearance to travel mine railways. The vehicle has power to all six wheels with power transmitted separately to either or both sets of wheels. Low-pressure, high-traction tires give the vehicle the ability to handle soft, muddy mine floors, flooded areas and significant obstacles, and can negotiate a 45% grade. Power and life support are sufficient for a 4-hour mission. The life support system is a commercially-available, approved unit currently used by MESA rescue personnel. A payout wire system provides communication between the vehicle and home base over a distance of 10,000 feet. On-board monitoring of carbon monoxide, methane and oxygen is provided, with master and individual alarms to warn of gas concentrations outside pre-set limits. A lightweight, water-tight trailer was developed for carrying victims or hauling tools and equipment.

Jan 1, 1979

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013