Search Documents

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By R. A. Leveille, M. D. Doggett

"Economic returns for the copper industry have been assessed by building cash flow models for each of the 100 new mines brought into production over the past 20 years. Ninety-one of the 100 new mines returned the assumed 8% cost of capital and generated a positive net present value (NPV) at the development decision point. Economic criteria for individual mines are highly variable with NPV ranging from -$111 million (-$111M) to +$3850M (all money values are presented in United States dollars) and internal rate of return (IRR) ranging from -8% to +95%. The copper industry collectively would generate approximately $39 billion dollars in NPV through the development of the 100 new mines.The returns to exploration ($174M per deposit) were measured by deducting the cost of exploration per deposit ($221M) from the returns to development per deposit ($395M). Overall, the copper business has provided positive returns to exploration. However, the variability in returns across deposits means that only 41 of the 100 new mines can carry the average cost of exploration. The long lead times and high costs associated with exploration result in only those deposits with large amounts of contained copper being able to cover the average finding cost of the industry.The returns to development and exploration are shown to be highly sensitive to the cost of capital and metal price assumptions. With respect to deposit type, porphyry deposits are both larger (NPV) and exhibit lower profitability (IRR) than the nonporphyry deposits. On a geographic basis, returns to development and exploration are higher in Chile than elsewhere, reflecting the larger average deposit size and lower average exploration cost per deposit."

Jan 1, 2009

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By G. L. Smith

This paper consolidates the key elements of seven contributions, on strategic long-term planning, to two of the three international conferences on Strategic versus Tactical approaches in Mining held over the period 2005?2008. The holistic concept of strategic long-term planning as developed and implemented at Anglo Platinum is described. Consideration is given to the planning cycle, principles supporting the construction of the long-term plan, and aspects of unique best practice as developed in Anglo Platinum. Further description of Anglo Platinum?s approach to corporate governance, including the processes, methodology, systems, unique tools and techniques that are applied to value and select capital investment options is also given.

Jan 1, 2009

By M. J. Farrell

The threat of global warming and its prominent position in public discussion and political debate requires all industry to take stock of its contribution to rising atmospheric concentration of greenhouse gases. For the primary metals industry, the first step must be to identify the pattern and range of emissions at each step in the production chain. Only then can the industry assess the economic consequences of the penalties on emissions that will be imposed by governments and regulators and devise cost-effective plans to avoid or mitigate such penalties. While some work has been done to estimate carbon dioxide (CO2) emissions using Life Cycle Inventory analysis, this approach is less useful than site-by-site emissions estimates. It is the level of specific emissions at each site that will ultimately deter-mine carbon taxation liabilities and participation in emissions trading schemes. Most mining companies have moved with the times to issue sustainability reports for their operations. But in the absence of any standardized reporting format, it is difficult to make useful comparisons between even the best-reported producers on a like-with-like basis. For this reason, Minecost.com modeled the use of fuels and energy used in mining, milling, shipping and metallurgical treatment to cover ?cradle-to-gate? emissions of greenhouse gases resulting from the production of the major base metals copper, zinc, lead and nickel. Greenhouse gas emissions ? overwhelmingly carbon dioxide ? are associated with the consumption of energy at every step in the production chain, from exploration through mining to the production of refined metal. Producers of primary metal employ diverse technologies to mine, mill, smelt and refine several different types of ore. Every orebody has its own special characteristics. In addition, most base metals are produced in concentrate that must be transported to smelters, with con-sequent emissions consequences.

Jan 1, 2009

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By I M. Platten, C J. S Sangster, Y Xie

The Cononish gold-silver deposit is a steep, relatively narrow quartz-vein system, with a current total mineral resource of 154 000 oz Au and 589 000 oz Ag. The northeast-southwest trending system was emplaced into late Proterozoic metasediments, and postdates metamorphism and associated Caledonian Orogenic foliations. Assay and mineralogical data show that gold and silver is spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur in small amounts. Gold occurs as electrum, with minor native gold, and silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally less than 100 microns in size. The main ore shoots plunge 45¦ south-west, have a 40 m to 80 m intersection with the existing underground development and extend between 40 m and 260 m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two, and rarely three, of the domains are present at an individual site in the vein. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Geological mapping along a 1.2 km exploration adit has provided critical æconditioningÆ data to support resource evaluation based on development and relatively wide spaced drilling. In addition, it has provided an indication of potential challenges that could be encountered during production.

Jan 1, 2009

Mineral liberation data are routinely obtained for a wide variety of applications, including ore characterization and characterization of various metallurgical test products obtained in bench-scale laboratory testwork. Newmont Mining Corporation owns several properties in the Carlin Trend containing refractory gold ores. These ores are generally difficult to treat and have to undergo several processing stages for gold recovery. At Carlin?s Mill 5 operation, flotation is used to pre-concentrate some of these difficult ores to produce a sulfide concentrate to feed the roaster. It is of interest from a flotation perspective to be able to study the floatability of pyrite, arsenopyrite and arsenian pyrite, since these minerals all have different quantities of gold associated with them, and have to be recovered to ensure a successful separation has been achieved. In this paper, a detailed MLA study on several Carlin ores was undertaken on samples from flotation tests, using air or nitrogen as flotation gas, specifically to study the differences in floatability characteristics, which ultimately impacts overall gold recovery. I

Jan 1, 2009

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.&nbsp; The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.&nbsp; Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.&nbsp; The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

As the 2009 George Fox Conference neared its conclusion, Arthur Silber, project chief of the Mass Transit Tunnel (MTT) project was able to pull away from the constant buzzing of his Blackberry long enough to give a short presentation and a significant piece of news to the record 318 attendees at the Graduate Center, City University of New York regarding the MTT project. ?As the former administration (The Bush administration) was leaving office, we were told that Congress was notified of the FTA?a (Federal Transit Authority?s) intent to issue final design construction approval to us,? Silber said of recent advancements concerning the $7.2-billion dollar project. It will add passenger rail service from New Jersey to New York City as part of the Access to the Region?s Core project in the form of the Trans Hudson Express Tunnel (THE tunnel). ?That 10-day waiting period ended yesterday (Jan. 26).? In days leading up the Fox Conference, those involved in the tunneling industry, and the MTT in particular, had a lot to be optimistic about. The MTT received environ-mental approval on Jan. 14 (see page 9) and, with the acceptance of the final design, the multi-billion dollar project moved that much closer to a ground-breaking ceremony. So close, in fact, that before leaving his office for the conference, Silber posted the contract documents and plans for the Manhattan Tunnel project online at www.arctunnel.com (an indepth look at the project from Silber is on page 22). While many were interested in the progress of the project, Silber also spoke about the new plans for the cavern complex at the New York Penn Station expansion. The original plans called for two lines that would come into a large cavern complex with a north and south cavern to access the trains. After numerous core samples were taken from the streets of Manhattan, it was deter-mined that this design was not feasible and changes were made that will include a deeper cavern under Sixth Avenue, with 14-m (45-ft) of cover with a 30-m (96-ft) wide cavern that resides entirely under 34th Street. The cavern was also moved 20 m (60 ft) to the west to remain at least 61 m (200 ft) away from New York City Water Tunnel #1. The new design will include three-over-three track arrangement. The mezzanine will be 46 m (150 ft) below street level at 8th Ave, Silber said.

Jan 1, 2009

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009