Search Documents

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By J. N. Van der Merwe

The research described in the paper was aimed at providing standardized information of cases of failed and intact coal pillars in the form of databases to researchers. It also offered the opportunity to take stock of the pillar stability situation in coalmining and to review the impact of the application of the safety factor formula for pillar design. It was found that the physical parameters of coalmining have not changed substantially over the last four decades. However, changes in the controllable parameters like pillar width, pillar width-to-height ratio and percentage extraction have all moved toward the more conservative side. Scrutiny of the database indicates that of all the failures recorded, only 23 occurred in panels that were mined after 1969, when one can assume that the safety factor formula was fully applied. If the pre-1969 practices had been continued, at least 144 collapses would have been expected. There has thus been a substantial reduction of pillar collapse cases, justifying the cost paid for the formula, which has shown to be in the region of 600 million tons of coal. It is evident that that are distinct differences in the natures of the failures among different coalfields. This justifies the attempts to derive seam or coal field specific strength formulae and is a topic that should be pursued.

Jan 1, 2006

By Ravichandar. D., K. B. Nagashanmugam, M. S. Pillai

"Blast furnace performance depends strongly on the coke reactivity index(CRI) and coke strength after reaction (CSR) properties. An innovative and cost-effective method, known as the Salem Box Test, has been developed to prevent the mass production of inferior coke unsuitable for blast furnace use. This method consists of coal carbonization on a micro-scale and involves charging approximately 18 kg of coal blend in a stainless steel box, carbonizing it together with coal cake in the plant coke ovens, and testing the coke produced for CRI and CSR to determine its suitability for blast furnace use. Only coal blends that yield coke with CRI <25% and CSR >64% are permitted for mass production, and other coal blends are either rejected or the blending ratios adjusted in an attempt to upgrade them. The experimental results reveal that, for a given coal blend, the quality of coke produced by the Salem Box Test is comparable with that produced by bulk production, indicating that the test is acceptable as a screening tool for regular use. The present paper describes the methodology and application of Salem Box Test to predict the suitability of coke for blast furnace use at JSW Steel Limited, Salem Works (JSWSL), and illustrates its advantages in adjusting the coal blending ratio to produce superior coke, in detecting coal contamination, and in preventing bulk production of inferior coke."

Jan 1, 2015

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By N. Z. Fotoyi

Keywords: MgO-MgR2O3 refractory, SO2-containing gases, chemical attack The reaction mechanisms occurring when MgO-MgR2O3 refractories are exposed to SO2-containing gas atmospheres were examined. The study examined the characteristic structures of magnesite-chrome, chrome-magnesite and magnesite refractories exposed to SO2-O2 gas mixture at temperatures of 700°C to 1350°C. The phase characterization was conducted with scanning electron microscopy (SEM) and powder X-ray diffractometry (XRD). The results show that the physical characteristics of the refractory matrix along the grain boundaries are important refractory features during chemical attack from SO2-containing gas. Upon heating in SO2-containing gas, the changes in phase-chemical compositions and accompanying grain growth causes loosening of the structure and the pore volume promotes gas diffusion. The chemical reactions that occur form stable sulfate compounds identified as MgSO4, CaSO4 and CaMg3(SO4)4, and lead to disintegration of various phase structures and consequently erosion of the refractory. In conclusion, the reaction mechanisms in MgO-MgR2O3 refractories exposed to SO2-containing gases progress through a combination of structural disintegration and chemical attack.

Jan 1, 2011

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008