Search Documents

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

By John M. Popovich

Disposing of coal mine waste at the surface has been and continues to be a problem which has yet to be resolved within the coal mining industry. A possible solution to this problem is to return the refuse back into the operating underground mine generating the waste material. It is believed that the approach described will provide an inexpensive and pratical solution to the problem. The designed system is installed and operable at the Millers Cove Energy Company, Inc. property in Lee County, Virginia. This system limits surfact facilities to a minimum size. It incorporates state-of-the-art hydraulic transport and backfilling technology and equipment to systematically backfill areas within the active mine. It maximized the benefits of reducing treatment of coal wasts while it minimizes environmental impacts on groundwater. The system approaches the problem in a manner to maximize benefits and minimize risks. The cost of returning coal waste back underground at the Millers Cove site is estimated at $0.67 per ton of marketable coal (1982 dollars), which is slightly higher than their surface disposal cost of $0.61 per ton of marketable mat (1982 dollars). The underground disposal costs do not include cost savings that should be realized within the preparation plant and treatment facilities at the surface. Preliminary tests of the system were conducted at the surface; funding restrictions prevented an in-mine trial. Efforts should continue to demonstrate the feasibility of solving the problem of refuse disposal. The installed system and plant at Millers Cove should provide the opportunity to test an underground disposal operation. This report contains guidelines to pursue this opportunity.

Jan 1, 1986

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Andrew M. Leszcykowski

In 1985, at the request of the Bureau of Land Management, personnel from the U.S. Bureau of Mines examined 18,700 acres of the 24,922-acre Eighteen Mile Wilderness Study Area to evaluate mineral resources. This study area is in east-central Idaho in Lemhi County, approximately 20 miles southeast of Leadore. The study area is underlain by Paleozoic marine sedimentary rock and Ordovician granitic rock. The sedimentary rock is primarily limestone and dolomite with a minor amount of siltstone. The Nicholia mining district borders the southern boundary of the study area. However, none of the district's mineral-bearing structures appear to trend into the study area. Just outside the northwestern part of the study area, on Clear Creek, is the E. J. Wilson and Sons? open-pit gypsum mine that operated until about 1977. About 120,000 tons of gypsum were produced from the mine for the cement plant at Inkom, ID, and for use as soil conditioner. Two theories for the origin of gypsum deposits are a hydrothermal source and a stratabound occurrence. Hydrothermal deposition is favored for this deposit. Occurrences of gypsum may exist in the study area. However, known reserves are adequate to meet needs for at least 800 years. There are no known mines, claims, or leases in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of part of the Eighteen Mile WSA (Wilderness Study Area) 1/ at the request of the Bureau of Land Management (BLM). The USBM examines and evaluates individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936