Search Documents

By O. Matwijenko

"The Kidd Creek concentrator is located twenty-six kilometres east of Timmins, Ontario, within a metallurgical complex including a 109,000 MTPY zinc plant and a new 59,000 MTPY copper smelter and refinery. A complement of 159 persons is employed in the operation of the concentrator.Ore from the Kidd Creek Mine is crushed underground to minus 15. 0 cm, then transported twenty-seven kilometres by rail 1:0 the concentrator. After being crushed to minus 1. 6 cm, the ore is further processed by grinding and flotation.The concentrator commenced operations in November of 1966 at a designed capacity of 8,200 MTPD. Two parallel flotation and grinding circuits treated copper-zinc ore (2.28% Cu, 5.63% Zn) and a third treated silver-copper-lead-zinc ore (230 g/MT Ag; 0.57% Cu, 0.88% Pb, 7.89% Zn).By 1975, the concentrator was treating 9,100 MTPD of ore. Seven concentrates were being produced, namely, high silve1: copper, low silver copper, lead, low silver zinc, high silver zinc, pyrite and tin.Planned minesite expansion to a second underground mine required increased concentrator throughput. Expansion of the concentrator enabling a thirty-three percent increase in copper-zinc ore throughput occurred during the period 1975 through 1978. This expansion included increased load-in capacity, major redesign in the crusher house, the addition of a fourth grinding and flotation circuit, the building of a fourth dryer, and numerous expansions of services."

Jan 1, 1980

By J. R. Eastwood

"H.D.P.E. Piping in the Mining IndustryThere has been much use· ms.de of high density polyethylene pipe in the mining industry over the past several years. This is not only in new installations but al.so in areas where other piping materials such as wood, transite, concrete and steel have worn out and failed.The uses of H.D.P.E. in the mining industry are as follows:Tailings disposal linesMine water supply linesTailings water return linesHydraulic backfill linesPit drainageCorrosive liquid supply and disposal linesH.D.P.E. pipe has many advantages for both underground and above ground installations. It is tough, flexible, weather resistant and inert which makes the pipe suitable for many installations."

Jan 1, 1975

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By Takahiro Kubo, Katsunori Yamaguchi, Hidehiro Sekimoto

Equilibrium relation between B2O3 slag, RExOy-B2O3 (RE = rare earths) slag and Fe-C alloy formed by melting treatment of neodymium magnet and B2O3 was investigated. When neodymium magnet was melted together with B2O3 and Fe-C alloy in carbon crucible, 3 liquid phases of B2O3 slag, RExOy-B2O3 slag and molten Fe-C alloy formed and clearly separated by the difference of the specific gravities. In the case that excess amount of Cu was also introduced in that system, molten Cu phase additionally formed. Almost all amount of RE were concentrated in RExOy-B2O3 slag. The concentration of RE in RExOy-B2O3 slag increased with the decrease of the melting temperature. While chromium, phosphorous, nickel, cobalt, and copper were concentrated in molten Fe-C alloy, silicon and aluminum were distributed in B2O3 slag and RE2O3-B2O3 slag.

Jan 1, 2014

By Robert E. McIvor

"The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill’s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “circuit classification system efficiency” (or CSE, McIvor, 1988a), and ultimately the discovery of the Functional Performance Equation (McIvor, 1988b, and McIvor et al, 1992). The CSE is the percentage of “coarse” (typically with reference to the plus P80) size material occupying the mill (versus “fines” or product size material, finer than the circuit P80), and can be calculated by taking the average of the percentage of coarse material in the mill feed and mill discharge. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, which is derived as follows.We define “fines” as any product size material, and “coarse” as that targeted to be further ground, the two typically differentiated by the circuit target P80. For any grinding circuit, the production rate of new, product size material (fines) must equal the specific grinding rate of the coarse material (i.e. fine product generated per unit of energy applied to the coarse material) times the power applied to the coarse material."

Jan 1, 2009

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By Ron Millions, J. A. Folinsbee, Ishwinder Grewal, Michael Fullam, Don Strickland, Tony Y. Chong

"Since milling began in 1912, the Dome mill, now part of the Porcupine Joint Venture (PJV), has been expanded several times, the most recent increasing the milling rate from 3,500 to 11,500 tonnes per day. Dome uses conventional crushing and grinding followed by gravity concentration to recover free milling gold. A cyanidation/CIP process recovers the remaining gold in the gravity tails.Over the past few years, continuous gravity improvements have increased the gravity recovery from 20% to nearly 50% of the plant feed gold. This paper describes some of the factors that have contributed to this dramatic increase, and suggests how gravity recovery can be further improved. Gravity circuit availability has been improved to >98% with the implementation of a preventative maintenance program. More Knelson concentrators have been added to the circuit, and in 2002, an Acacia Intensive Leach Reactor was installed to replace the shaking table. In 2003, the entire gravity circuit was audited to evaluate and quantify the circuit performance. The metallurgical and mechanical operating conditions of the gravity circuit are now well understood, and areas for further improvement are well defined.INTRODUCTIONThe Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. One of the goals of the JV was to use the milling capacity of the Dome mill to process ore from Placer Dome and Kinross mines in the Timmins Camp. The PJV Dome Mill utilizes gravity concentration, cyanide leaching and carbon in pulp gold circuits to recover gold. Gravity recovery has been used in some form at the Dome Mill for most of its existence, first using conventional jigs, these being replaced in 1993 by two Knelson Concentrators, one for each of the two grinding circuits in the Dome mill. Over the years more concentrators have been added to improve the gravity recovery, most recently in 2002 for a current total of five. Also in 2002, an Acacia Intensive Leach Reactor was added to process the Knelson concentrate, replacing the shaking table."

Jan 1, 2004

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995