Search Documents

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By D. M. Davidson, P. F. Kerr

The Permian Cutler Formation in Kane Creek, Utah bears uranium ore in fissure-type vertical veins. This fissure vein formation and its associated host rock bleaching, weak argillic alteration, and base-metal sulfide mineralization along with the development of hydrothermal minerals, a 60 m.y. isotopic Pb/U age, and well-crystallized uraninite's structural control, give evidence of ore deposition in a hydrothermal environment consistent with Laramide mineralization. Mica polymorph studies indicate first, that temperature during the hydrothermal alteration or subsequent ore deposition did not exceed 200°; hence Cutler deposits are classified telethermal; and secondly, that rock alteration and ore deposition are closely related both in time and space, as is seen in argillic alteration sequence. Ore deposition in an alkaline to slightly acid reducing environment is postulated. Ore textures and mineral associations and distributions also indicate that carbonate complexes may have been transported with the deposing ores. Bleached rock formations are not primary strati-graphic phenomena. Bleaching, or changes in ferric iron content, results from a chemical process involving reduction and conversion of hematite to a soluble aqueous ion. Nearby Chinle bedded deposits (Moss Rack sandstone), containing shale lenses, fossil wood, organic debris and minor fractures, overly the Cutler formation. Chinle ores have a single reported isotopic age of approximately 200 m.y. Their chemical environment is assumed similar to that of the Cutler ores, though slightly more acidic. Two genetic, paradoxically divergent interpretations of the bedded deposits are derived from available spectrographic, petrographic, X-ray and chemical analyses. Kane Springs canyon is located southwest of Moab, Utah, south of the Colorado River and northwest of the Lisbon Valley mining district (Fig. 1). Uranium deposits occur along the northeast flank of a Kane Creek salt anticline where two geologic formations bear ore, the Permian Cutler and the Triassic Chinle. The Cutler deposits' fissure vein formation is an unusual occurrence in the Colorado Plateau. The Chinle deposits appear to be of the normal sedimentary type. Associated with the vein deposits are a number of features, including argillic alteration of sedimentary strata. The minerals of these deposits and their associated features have been studied in detail in a two year program entailing both field and laboratory techniques. STRATIGRAPHY A stratigraphic section of the lithologic units in the Kane Creek area is given in Table I.

Jan 1, 1967

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By G. W. Thomas

Jan 1, 1967

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By David Schroeder, John Chipman

Jan 1, 1964

By E. Douglas, D. N. Collins, J. R. Stevens

E. Douglas (Dept. of Scientific and lndustrial Re-search, Warren Spring Laboratory, Hertfordshire, England) — The authors are to be congratulated on the considerable improvements they have made in tailoring efficiency and selectivity terms which are generally superior to the alternative forms in current use. However, I feel that their efficiency expression is limited to lower-grade feeds; its accuracy reduces as the feed grade increases. For example, its application to such processes as the beneficiation of glass sands, refractories and clays will invoIve considerable inaccuracies. The reason for this lies in the direct use of recovery, which, with high-grade feeds, biases their empirical expression, R(1 - c/h). With a 90% grade feed, the recovery weighting for the slightest degree of beneficiation, over a zero efficiency sampling operation, will be 90+%+ I disagree with their second basic requirement which states that there can be no fundamental basis for any single quantifying expression. A formula giving a comprehensive representation of concentra- tion efficiency can be derived fundamentally accord-to the procedure outlined in the literature. '' This formula, called the Basic Efficiency formula, is

Jan 1, 1963

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By J. F. Butler, H. W. Paxton

The vapor pressures of manganese in equilibrium with several alloys in the iron-manganese-carbon system between 1200° and 1275°K have been measured using the Knudsen effusion technique in conjunction with a vacuum microbalance. The effect of orifice area of the effusion cell upon the measured pressure has been determined. The binary iron-manganese system shows small negative departures from ideality, and the system of mixed carbides, (Fe, Mn)7C3, in equilibrium with graphite behaves ideally. THIS work is a continuation of the investigations in which the Knudsen effusion method has been used to determine thermodynamic activities in systems and at temperatures of interest to metallurgists. In a previous publication,' the free energy of formation of Mn7C3 was determined and some preliminary work on the solution behavior of this carbide with the hypothetical "Fe7C3" was reported. The present work deals with this latter topic and also includes data on the binary ir-on-manganese system. EXPERIMENTAL METHOD The Knudsen effusion method was used to measure the vapor pressure of manganese in both the alloy and carbide sections of this investigation. This dynamic method of vapor pressure measurement presents a problem when studying solid alloy systems in which one of the components has a much larger vapor pressure than the others. Over-all depletion of the alloy in the most volatile component will occur during evaporation so that the pressure of that component will decrease. Even more serious than the over-all concentration change is the surface depletion of volatile component in the alloy brought about by the slow rate of diffusion of this component from the interior to the surface of the solid particle. Since knowledge of this surface composition is necessary in order to relate it to the activity determined through the measurements, changes in surface composition from the analyzed bulk composition are to be avoided in dynamic vapor pressure studies of solid alloys. The system under investigation in this study presents the problem of surface depletion of manganese since its pressure at 1230°K is 105greater than iron and 1020 greater than carbon. Since the existence of a volatile manganese carbide had been ruled out previously,' the high manganese pressure relative to iron and carbon insured that the only species leaving the effusion cell was manganese. Therefore, the effusing species required no analysis so that the manganese pressure was determined directly from the weight loss of the effusion cell. In order to detect small weight losses near the beginning of effusion, a vacuum microbalance was used to weigh the cell continually. These initial weight loss data allowed the rate of manganese effusion to be determined before the surface of the alloy became depleted in manganese. The apparatus used in this investigation is shown in Fig. 1. Temperature was measured using chro-

Jan 1, 1962

By I. Cadoff, E. Miller, K. Komarek

Jan 1, 1960

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By V. J. Parks, Leonard Obert, A. J. Durelli

The state of stress in the region where core discing initiates has been investigated through the use of three-dimensional photoelastic models and the results of this study have been compared with those of a previous investigation of rock models. This comparison showed that discing initiates at a point of maximum shear stress, but that the magnitude of the shear stress, as determined photoelastically, is much larger than the shear strength of the rock as deter-mined from conventional triaxial testing. Moreover the shear stress required to produce discing is not constant, but depends on the applied stress field. Possible explanations for these effects are included in this article. In both exploration core drilling and overcore drilling to determine the stress in rock, occasional sections of the core obtained are broken into a series of discs.I* This discing phenomenon has been investigated in the laboratory to ascertain the state of stress required to produce it. The objective of the study was to obtain information that would make it possible to approximate the state of stress in subsurface rock from which disced cores are obtained. Referred to as the discing test, this laboratory study was conducted to determine the applied axial and radial loads required to produce discing in cylinders of rock from several sources. The dimensions of these cylinders are given in Fig. 1. Discing was produced by first applying an axial load to the cylinder and then diamond drilling the core along its axis. The radial load was then incrementally increased until discing initiated. The discs fractured or ruptured* on surfaces approximately normal to the axis of the core (planes A, B, C, D, E, Fig. 2). In many instances, the bottommost disc fractured before the drill had advanced past the points F and F', cre- ating a mush room-shaped fracture surface FEF'. Alternatively, it was also found that the same shaped fracture surface could be created by first drilling in an unloaded core to some point, say F and F', and then triaxially loading the core until fracture occurred on the plane FEF'. Jaeger and cook4 produced similar fracture surfaces in specimens subjected only to a radial biaxial load. From these laboratory studies and observations made in the field, it can be inferred that fracture or rupture initiates in the proximity of the lowest point in the kerf area, (at F and F', Fig. 2) and that the fracture or rupture surface progresses inward from this point. The experiments described above, however, do not provide any information as to the state of stress at the point at which fracture or rupture initiates. In the investigation discussed in the following sections, a three-dimensional photoelastic analysis was conducted to determine the stress distribution in the proximity of the kerf area of a triaxially loaded plastic (epoxy) cylinder containing a short section of core.

Jan 1, 1969

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914