Search Documents

By Jeremy Spearman, Mark Lee, Jon Taylor, Neil Crossouard, Bramley Murton

"SUMMARYThis paper describes challenges faced when executing a programme of monitoring to measure the dynamics of currents and sediment plumes at a seamount and the solutions identified to deliver the measurements. The study site was the Tropic Seamount, which extends some 3300m above the surrounding seabed and is found at the southern limit of the Canary Island Seamount Province. The purpose of the study, which forms part of the Marine E-tech project, was to provide information on the interaction of flows with the seamount and to assess the behaviour of sediment plumes that could be generated from potential seabed mining operations targeting the recovery of ferromanganese crusts. Since the crest of the seamount is submerged to a depth of 1000m, much of the work was undertaken using remotely operated and autonomous vehicles supported by measurements from the surface vessel. Despite only limited information on currents being available for planning purposes, the combination of short term forecasting using a 3-dimesional hydrodynamic model of the study area coupled with the collection and analysis of reconnaissance data collected during the first phase of measurement activities made it possible to plan and execute a number of detailed hydrodynamic experiments on the seamount crest. The results of these experiments have advanced the understanding of the behaviour of sediment plumes in the deep ocean and will ultimately improve our ability to manage the impacts which may arise from deep sea mining operations."

Jan 1, 2017

By W. G. Stevenson

The centennial celebration of the AIME provides an opportunity to review some aspects of developments in mineral exploration since 1871 and to reflect on the changes that have occurred. During this period seven Factors have fundamentally altered the procedures, techniques and philosophy of mineral exploration. Although most of these developed gradually, and unheralded, they have drastically altered the art of exploration and discovery. 1. ADVANCES IN MINING AND MILLING The development of huge shovels, draglines, trucks and track-mounted drills, to replace the wheelbarrow and single Jack has drastically expanded the rate of production for both underground and surface mining. The development of selective flotation has had a far-reaching affect on mineral exploration and has made it possible to extract metals from the metallurgically complex deposits discovered years before. These developments have reduced the costs of mining and treatment, and have transformed material into ore that was considered waste one hundred years ago. These advances have permitted exploration for progressively lower grade and larger mineral deposits.

Jan 1, 1971

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By Bennett McLaughlin

AGNICO-EAGLE started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1,800 tonnes per day from a 2,240 metre deep shaft. Exploration success lead to the installation of a hoisting plant capable of extracting 4,500 tonnes of ore and 1,800 tonnes of waste per day from a depth of 2,210 metres. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

May 1, 2001

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

Thallous chloride and cadmium metal were recovered from a thallium-cadmium concentrate by a method suited to the treatment of small batches. Differences in oxide solubility and control of pH were employed to separate the thallium and cadmium. The cadmium metal produced by zinc reduction analysed better than 99.95 per cent Cd and thallous chloride of high purity was precipitated from solution.

Jan 1, 1969

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By M Baker

Biodiversity offsets are conservation actions intended to compensate for the residual, unavoidable harm to biodiversity caused by development projects. The use of biodiversity offsets in the context of mining has significant potential for enabling mining to take place in areas with biodiversity values, where it would not otherwise be possible to meet the relevant legal tests under the Resource Management Act 1991, and potentially the Conservation Act 1987. This paper looks at the concept of biodiversity offsets (and environmental compensation generally) both in New Zealand and internationally, and considers how lessons learned overseas may be adapted for this country. In New Zealand the practice of biodiversity offsets and environmental compensation is ad hoc and variable. The challenge with biodiversity offsets is to establish a transparent and coherent means of identifying the overall priorities and objectives of adopting such an approach, as well as how the relevant values are measured and protected. Establishing a methodology for quantifying biodiversity value, and the need for clear policy guidelines on biodiversity offsets are identified as key areas in need of wider discussion.

Jan 1, 2007

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By Manis Kumar Jha

Leaching studies were carried out for the recovery/ recycling of metals from PCBs containing 17.05% Cu, 0.74% Ni, 1.74% Fe, 4.35% Pb and 8.32% Sn using various acids such as H2SO4, HCl and HNO3. While sulfuric acid was not a suitable leachant for the dissolution of metals from PCBs, hydrochloric acid selectively dissolved tin. The nitric acid was found to be effective lixiviant with the recovery of 99.99% Cu, Fe, Ni and 36.7% Pb in 6M HNO3 at S/L ratio of 100 g/L and 90oC. The kinetic studies carried out with 2M and 4M HNO3 at 90oC showed ?Ash diffusion control dense constant size-spherical particles? model.

Jan 1, 2010

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986