Search Documents

By S. I. Angadi, C. Eswaraiah, Sunil Kumar Tripathy, T. Santosh, Nilima Dash

Banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) ores represent a promising potential iron ore resource in the near future. The hematite and quartz in BHQ and the hematite and jasper in BHJ are closely related and require fine grinding for the liberation of hematite phases. The present study investigates the mineralogical features and comminution properties of BHQ and BHJ ores. In the BHQ ore, it is observed that thick bands of hematite have fine inclusions of silicate minerals, whereas silica bands have few grains of iron-bearing minerals. The hematite and quartz minerals in the iron and silicate bands of the BHJ ore appear to be more intricately associated and complex in nature, presenting difficulties for liberation. Bond work index studies were carried out for the BHQ and BHJ ores with different product fineness in order to evaluate the energy requirements in fine grinding. A higher Bond work index value was found for the BHJ ore (15.4 kWh/ton) than for the BHQ ore (12.4 kWh/ton). A decrease in the product particle size was associated with an increase in the work index value. Single-particle breakage experiments were designed by varying feed particle size and input energy. The specific energy consumption for the BHJ ore was higher than that for the BHQ ore. The comminution parameters showed that the BHJ ore is harder to grind than the BHQ ore, which may be due to the mineral composition and association of hematite phases with the silicates.

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

Updating the openpit vehicle transportation network has the problem of being time consuming and low precision. To address this problem, a high-precision road network model construction method for unmanned vehicles in openpit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3+C (DeepLabv3+Concat) is presented, and the road information extracted by the DeepLabv3+C network is used to construct a three-dimensional model of the openpit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicles meeting in openpit mines, a vehicle meeting strategy is proposed. This strategy is used to guide the navigation of unmanned vehicles in openpit mines. At the end of the study, vehicle running simulation was carried out on the road network model using Unity, a 3D visualization simulation software. The high-precision unmanned road network model of openpit mines studied in this work can further promote the construction and development of smart mines by acting as a high-precision map for unmanned vehicles.

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By Robert M. Becker

This investigation (in five parts) extends the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The extension of the theory is confirmed by experimental laboratory sampling using standard procedures. The probability distribution functions (the binomial, hypergeometric, multinomial, generalized hypergeometric, and those here called the compound binomial and compound multimomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, and finite population moments are developed from corresponding infinite population moments using a newly defined mathematical operation. The first three experimental moments in laboratory sampling to given weights of particles are compared with the theoretical moments of their corresponding compound mult.inomial distributions. The agreement is striking. The study is divided into five parts. Part 1 deals with probability or random sampling to n items and with all sampling to n items per sample from some one probability distribution. This is the area of sampling covered by well-known theory. Accordingly, the procedures may be different but many of the results are well known.

Dec 1, 1964

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By C A. Fleming

Gold extraction is largely driven by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery include grain size and shape, surface coating or rimming on gold particles, the presence of cyanide or oxygen-consuming minerals or preg-robbers, the presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking of fine gold particles in sulfide, silicate and other minerals, either as visible, fine-grained gold inclusions and/or as invisible submicroscopic gold, is by far the most common factor leading to poor gold recovery in gold ore processing. This paper discusses the mineralogical characterisation of gold lost in tailings and its metallurgical implications. The techniques used in characterising the un-recovered gold are also briefly introduced.

Jan 1, 2007

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By B. J. Moore

This Bureau of Mines publication contains analyses and related source data for 276 natural gas samples from 23 States. All samples except four were collected during calendar year 1984. Those four samples were collected earlier, but releases granting permission to publish were not received until 1984. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-eight publications have presented the results of 13,957 gas analyses made prior to 1984. The first three bulletins (1-3)2 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-28) containing 8,453 analyses of samples collected since 1960.

Jan 1, 1985

This paper reviews the gold mining history and recent exploration activities on a number of beaches in the Catlins area of coastal South Otago. Past mining history and recent sampling indicate the presence of economically significant concentrations of placer gold, as well as anomalous PGM, and various heavy mineral species. A local source for this placer mineralisation is considered a strong possibility, along with a contribution from the Waiau River catchment via longshore drift. Blacksand beds in Jurassic sandstones of the Southland Synclinorium may represent this local source of mineralisation on the modern beaches. The possibility of placer mineralisation extending onto the inner continental shelf is also considered. Further exploratory work is justified, both for in situ Jurassic blacksand deposits, and to delineate mineralisation in the modern beach and inner shelf environment.

Jan 1, 1992

By Steve Kral

Amax Coal Industries Inc.'s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state's oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By S A. Myers, T Klein

The Yanacocha mining district is located in the northern Andes of Peru. The project is within the Cajamarca province, 20 km north of the town of Cajamarca and 600 km north of Lima, the capital of Peru (Figure 1). The district encompasses an area of 120 km 2 and is centred on the 78030'west longitude and 7000' south latitude. The project lies at an elevation of 3400 to 4200 masl.

Jan 1, 1999