Search Documents

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By Paul Gribbon, Julius Strid, Greg Colzani, Jim McDonald

Portland, Oregon’s $370 million West Side Combined Sewer Overflow Tunnel Project has completed the final phase of construction and commissioning. The construction contract, which began in September 2002, was a reimbursable cost plus fixed fee contract that followed a qualifications-based contractor procurement process and apre-construction planning phase. This paper addresses the final results of the contracting method and provides a lessons-learned case history. Specific items addressed include the benefits realized from the contracting method, areas of improvement, final costs compared to the original contract estimates, design changes and schedule impacts, and subcontract management issues.

Jan 1, 2007

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from prototypes to production-ready applications, the operating performance of the haul road will become critical to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width. This will, therefore, generate potentially significant reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and its associated deterioration rate, is predictable and manageable, based on the materials used to construct the road and the maintenance interventions to be carried out on the road.This article presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined partly from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this article, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images that are analyzed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration.Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management and, although the quality of mine roads have probably"

Jan 1, 2015

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By Caio Moreira, Saulo De Rezende, Nelly Ruíz

The present project sought alternatives for this material through the Mining Lab Beginnings program, which was developed by Nexa in partnership with Escalab to find solutions for the company's highly complex challenges. Through the program, several solutions were evaluated, with additives for the construction market being the most prominent. Tests were conducted to confirm the efficiency of jarosite in the mixture that composes this material. With successful laboratory tests, the technology was tested on an industrial scale, where it also demonstrated its technical and economic viability. The project is now moving into the operational phase, demonstrating that circular economy is the best solution for disposed tailings.

Sep 29, 2023

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By John B. Gustavson

This paper describes a case history of geochemical prospecting. An area of known mineralization was available for an orientation survey which led to the selection of elements and criteria for a reconnaissance survey in the area offsetting the known mineralization. Certain anomalies were found which were then made subject of confirmation sampling and of rock geochemical investigations. Inasmuch as the geochemical prospecting technique specifically led to a detailed area which now serves as a target for drilling and other exploration efforts, the geochemical prospecting part of the program is considered successfully concluded and, therefore, reported on here. Whether the target area will turn out to host the deposit or not is, of course, of utmost importance to the Company, but is of less importance to this paper. We will describe the concepts, the planning, the execution, the analysis and the interpretation of this typical geochemical prospecting case. A number of people on the staff of International Oil & Gas, Inc. have participated in this prospect, as have students from Southeast Missouri State University and their professor, Gary M. Lowell. In addition, the Missouri Geological Survey has been most helpful with records and letters on the century-old prospecting and mining in the general area. Many valuable discussions have also been held with geologists from the industry who, from time to time, have visited the area, examined the property and reviewed the status of the project. The support and interest from all these parties has made it possible to pursue and expand this exploration concept from one of being just "more of the same kind" to the most chal-1enging and exciting with which this author has ever been involved, namely the prospect for tin porphyry deposits in the mid-continent United States.

Jan 1, 1977

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By Oswaldo Ortiz Sánchez

El presente trabajo describe la alternativa de uso del mortero de resina en la fijación de pernos de anclaje de las excavaciones mineras, consolidación y disipación de vibraciones en los cimientos de plataformas para la instalación de molinos, winches, tolvas, etc. Esta opción surge en respuesta al problema de reforzamiento con pernos de anclaje en ambientes con aguas corrosivas o en proceso de deformación acelerada en las excavaciones mineras, así como ante obstáculos de subsidencia de cimentación en plataformas, donde se encuentran instalados equipos de gran tonelaje, y que producen fuertes vibraciones durante su funcionamiento.

Jul 31, 2003

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975