Search Documents

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By AIME AIME

WILBER JUDSON is one of that fairly large group of mining engineers that graduated at an Eastern college, worked his way up in various jobs in the West and in the Latin-American countries, and finally came to New York as an administrative officer of a large mining company. Since coming to New York he has been a loyal friend and counselor of the A.I.M.E., and is now serving a second term as one of its Directors, his first term covering the period 1935-1938. Mr. Judson was born in the capital city of Michigan on July 26, 1880. Probably it was his roving spirit rather than professorial urging that was responsible for the fact that four colleges were responsible for his education: Northwestern, University of Michigan, Harvard (S.B., 1901), and the Michigan College of Mines (graduate study). In his first ten years of professional work he might have been found serving as mine foreman at Catamarca in the Argentine, as superintendent of the Inter Ocean mine at Sunshine, Colo.. as foreman for the Cerro Prieto, Magdalena, Sonora, as superintendent of the Hudson Iron Co. in New York, or as manager of the Dolores mine in Chihuahua for the Mines Co. of America, or in Spain, or in Panama.

Jan 1, 1942

By Peter Waggitt

Northern Australia has been home to uranium mining for over 70 years, more or less continuously. In the early days, post World War 2, there was little effort made to remediate workings at the end of operations. The three “campaigns” of uranium mining (1951-55; 1960-70; and 1979-present) are all now in various stages of remediation. This includes not only the large legacy site at Rum Jungle but also smaller fields like the South Alligator Valley, as well as contemporary works at Nabarlek and the ongoing closure at Ranger– Australia’s longest operating uranium mine. This paper briefly describes some of the past remediation activities before providing an update on the Ranger closure programme and future timetable.

Jan 1, 2020

All aspects of precious metals processing were featured at a symposium held Oct. 3-6, 2007, at Loews Ventana Canyon Resort in Tucson, AZ. Although billed as "Precious Metals Processing: Advances in Primary and Secondary Operations," the symposium also looked at economic, regulatory and environmental issues affecting the precious metals industry. The symposium was sponsored by SME; The Minerals, Metals & Materials Society (TMS); and the International Precious Metals Institute (IPMI). It included workshops, technical presentations, guest speakers and social activities. Mining industry management, process engineers, equipment manufacturers, consultants, metals marketers, academics and others involved in the precious metals industry attended the conference. Needless to say, with gold nearing $25.721g ($800/oz) and platinum pushing $41.801g ($1,300/oz) at the time of the meeting, the mood among the attendees could not have been more positive. The symposium was privileged to have Father Ernest S. Sweeney, professor of Latin American History at Loyola Marymount University, as a guest speaker. Sweeney, a Jesuit priest, provided a colorful account of the history of mining in Arizona and the surrounding region of North America (Fig. 1). He described the importance of the mining industry and said, "To go down into the bowels of the earth to extract its riches for the benefit of all of us is an awesome task deserving our sincere respect and gratitude." However, he warned the industry that: "The ever increasing de¬mands on the mining community for the protection of the environment calls for endless efforts to maintain ethical standards in a business filled with risk, uncertainty and frustrations." Sweeney noted that the Spanish conquest of the Americas was driven by the three fundamental motives of "God, glory and gold." He noted that gold was the basic, most powerful driving force of the conquest and occupation of the Spanish empire. The first European to explore Arizona was the Franciscan missionary Marcos de Niza. He came to Arizona in 1539 in search of the fabled Seven Golden Cities of Cíbola. Sweeny noted that Spanish explorers were consumed, as Cortes himself described it, "with a burning fever that only gold could cure." Sweeney told the story of some of these early explorers, including Francisco Vázquez de Coronado who "mounted an expedition in pursuit of gold and rich empires to conquer." Coronado passed through Arizona and discovered the Grand Canyon. "Coronado returned to Mexico exhausted, bankrupt and disillusioned, but with a wealth of new knowledge of the borderlands of the Spanish empire," said Sweeney. He then described the colorful history of early gold, silver and copper exploration and mining in Arizona, including the famous tale of the Lost Dutchman's Mine. In a luncheon address, David Kanagy, SME's executive director, introduced the attendees to the upcoming OneMine. org Web site. Kanagy told the audience" One-Mine.org will be a collaborative digital library that will

Jan 1, 2008

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

REFERENCES AND FOOTNOTES 1. U.S. Department of the Interior, Office of Surface Mining. Surface Coal Mining Reclamation: 10 Years of Progress: 1977-1987. Washington, D.C. August 3, 1987.48 pp. (For sale by the Superintendent of Documents, U. S. Government Printing Office, Washington D.C. 20402.) 2. The Rural Abandoned Mine Program (RAMP), authorized by Section 406 of SMCRA, provides for the control and prevention o f erosion and sediment damages from unreclaimed abandoned mine lands. 3. The Small Operator Assistance Program (SOAP), authorized by Section 401(b)(1) and 507(c) of SMCRA authorizes up to 10 percent of the fees collected for the Abandoned Mine Reclamation Fund to be used for technical assistance to help qualified small mine operators obtain techincal data needed for permit applications. Operators who produce fewer than 300,000 tons of coal per year are eligible for assistance. 4. OSM regulations 30 CFR 816.42 and 817.42 require water from areas distrubed by mining activities be in compliance with all applicable state and federal water-quality laws and effluent limitations for coal mining established by the U.S. Environmental Protection Agency. 5. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 6. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 7. Source: OSM Field Office Annual Reports. 8. Johnson, W. and G.C. Miller, Abandoned Coal-Mine Lands: nature, extent, and cost of reclamation. U. S. Bureau of Mines, 1979,29 pp. PHOTOGRAPHIC CREDITS Front cover, pp. i, 1, 2 bottom, 7 right, 10 bottom left, l 1 top, l l bottom right, 12 top, 13 bottom, 14 bottom right, 15,16 bottom, 17 top, 17 bottom right, 18 bottom, 19, 20 bottom, 21 top, 22, 23, 24 bottom, 25 bottom, 26 bottom left, 26 bottom right, 27, 28, 29 top, 30 bottom, 32 bottom right, 33 top, 34 top, 35 top left, 35 bottom left, 35 bottom right, 36 top, 37, top right, 37 bottom, 38 bottom, 39, 41, 42 top, 43 bottom, 44 bottom left, 44 bottom right, 45, 46, 47, and 53: Chuck Meyers, OSM. Page 2 top and center: Tony Fuhs. Page 3: John Sharkowicz, OSM. Page 6 left: North American Coal Corp. Pages 6 right, 7 left, l l bottom left, 13 top left, 13 top right, 17 bottom left, 21 bottom, 25 top left, 25 top right, 29 bottom, 30 center, 32 top, 32 bottom left, and 38 top: Bob Welch, OSM. Page 10 top left: Donald Stump, OSM. Pages 10 right, 14 top right, 14 center right, 18 top, and 44 top: Ron Hill, EPA. Page 12 bottom: Texas Utilities Co. Pages 16 top, 20 top, 24 top: Tennessee Valley Authority. Page 26 top right and 26 center left: Richard Dick, U.S. Bureau of Mines. Pages 30 top, 33 bottom left, 33 bottom right, 35 top right, 36 bottom, 37 top left, 40 top, 40 bottom, 42 bottom, 43 top left, and 43 top right: Jim Boyer, OSM. Page 31 top left, and 31 top right: Bruce Wage, Western Energy Co. Page 31 bottom: Rex Wilson, OSM. Page 34 bottom: West Virginia Division of Abandoned Mine Lands. Page 35 center: William Weist, Jr., OSM.

Jan 1, 1992

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation.

Jan 1, 2001

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By Poul Hansen

"In mid-I986, a world-class mining enterprise was created in British Columbia, bringing together the copper mining operations of Lornex Mining Corporation and Cominco into a new entity, Highland Valley Copper. This paper will focus on the background and rationalef or the formation of this partnership, the resulting operating changes and the productivity and cost benefits expected.IntroductionSince the deterioration of the world copper industry in 1981, the future of the Lomex and Cominco mines in the Highland Valley of British Columbia looked increasingly precarious. Despite the expansion of the Lomex mill complex in 1981 to one of the world's most cost-efficient copper and molybdenum concentrators, persistent low metal prices had made the remainder of the ore in the Lomex orebody marginally economic and had significantly foreshortened the expected life of the operation.Cominco had acquired the Bethlehem Copper assets in order to consolidate its ownership of the Valley orebody, and was feeding the Bethlehem concentrator with ore from the Valley orebody. In spite of the high grade and free-milling character of the Valley ore, profitability of the Cominco operation was severely restricted because of the limited capacity of the Bethlehem concentrator and its location high on the hillside above the orebody."

Jan 1, 1987

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961