Search Documents

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By GEORGE D. RAMSAY

WHEN the Ironton blast furnace of the Columbia Steel , Co. was first put into operation the iron ore was mined frol11 the deposit near Iron Springs, Utah. This is principally a hematite with 12 to 20 per cent of magnetite finely disseminated throughout the ore. It varies from a fairly soft broken rock structure to that which is hard and compact. In the broken form it will weigh about 150 lb. per cu. ft., and in place the density is approximately 250 lb. per cu. ft. The first ore received for the blast furnace was crushed so as to pass through approximately a 4-in. square opening screen. A typical screen test of this ore is shown in Table 1.

Jan 1, 1935

By T. R. Jr. McMillan

Introduction Examining the short- and long-term job prospects for engineers in the coal industry might include looking at coal tonnage projections, future export markets, federal regulations, and the decrease in overall graduates. But coal is the US most competitive basic industry. As such, why not go back to basics? That is, there are three basic challenges that need to be faced by students, faculty, and members of the coal industry. These challenges are counseling, career placement, and professionalism. Counseling Counseling can include elementary, high school, and college students, as well as individuals already employed. But what happens to students after they have selected a course of study at a particular university? As shown in Fig. 1, only 87,000, or 7.25% of our graduates have technical degrees. Generally, there is a strong market projected for these engineering graduates. However, many students who have majored in other nontechnical curriculums, have to scramble for jobs. This says something about our ability to make students aware of where the real job opportunities are. As a student spends four or five years pursuing a degree, he or she is looking for professional guidance. The student has the right to expect "real world" counseling - counseling that is not "the way it should be" but "the way it is." The influence of faculty members is significant. They should take this long opportunity to tell students not what they want to hear or what the problem's of academia or the industry are, but what the real job market is all about. If faculty do not use this opportunity, they in-advertently-through omission - mislead their students. Once a student graduates and is a working alumnus, faculty should take advantage of their relationship with the student and continue to stimulate conversation leading to a two-way exchange of ideas and information. Faculty should also encourage and solicit financial support for their mining departments from their alumni. These monies, in many cases, will be matched dollar for dollar or more, depending on the company the alumnus works for. In the private sector, the responsibility is to communicate with faculty and students. Alumni can be effective by participating in this two-way dialogue with their professors at meetings, technical seminars, and conventions. In many cases, alumni will employ summer or co-op students in their organizations. While getting to know these students, industry members should level with them on where the true opportunities are and what it takes to be successful. It is important to communicate with both faculty and students candidly on both the posi-

Jan 2, 1985

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

Selective Removal of Arsenic from Acid Mine Drainage Containing Ferrous Ion Using Sulfide Precipitation Method

Sep 13, 2010

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By PHILIP N. MOORE

THE development of the power of the Tennessee River at Muscle Shoals has become a matter of political interest as well as engineering possibility. The controversy over it has been so active that the facts have been obscured, the possibilities exaggerated. Although the members of the American Institute of Mining & Metallurgical Engineers are not generally specialists in hydroelectric development, those who visited Muscle Shoals in October, following the Birmingham meeting of the Institute, were interested, and many of them surprised to learn the actual conditions. These have long been familiar to those who have studied the matter through the reports of the U. S. Engineers on the subject. The approved plan contemplates three dams-No. 1, a low dam close to the City of Florence, planned in the interests of navigation, since the construction of the other dams has rendered impossible the use of the river without it. No. 2-named the Wilson Dam is now under construction. Concerning it political argumentation has waged. No. 3 Dam-much smaller, is planned to be erected several miles above No. 2.

Jan 1, 1925

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By José De Piérola

En los procesos de flotación y lixiviación de la producción de cobre se utilizan aguas recicladas y agua fresca. Este último es un insumo indispensable para ambos procesos, ya que constituye un elemento determinante del volumen de producción, así como un medio de vinculación obligado con el entorno social de las operaciones. En ese sentido, el presente texto describe la utilización del agua- en tanto representa un componente de rentabilidad relacionada al costo, al equilibrio del aprovechamiento con el comportamiento de la fuente y a la sostenibilidad con el entorno social, lo cual implica compartir el agua y recursos económicos para una planificación y adecuada priorización en su asignación.

Sep 9, 2007