Search Documents

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Jeremy Morris

The city of Indianapolis has more than 25,000 homes currently on septic systems. Many of these systems do not function well because of their age and surrounding soil conditions. As Indianapolis has worked to eliminate septic systems and install sanitary sewers in large unsewered areas on the north-west side, capacity of the existing Belmont North Interceptor (BNI) became a concern. The BNI system currently services an area of approximately 80 km2 (31 sq miles) located within the northwest quadrant of the city (Fig. 1). Monitoring of the existing interceptor indicated portions of the sys-tem flowing half- to two-thirds full during dry weather conditions and surcharging during some wet weather conditions. Further analysis of the BNI based on growth projections coupled with increased sewershed yield resulting from the city?s septic tank elimination program (STEP) indicated dry-weather flows could potentially triple over the next 20 years. Based on these modeling results and current wet weather capacity issues, the city determined further STEP projects could not be performed within the BNI service area until

Jan 1, 2011

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By A Giblett, K Afewu

This paper uses a case study to demonstrate best practices techniques for predicting the contribution of gravity concentration in a gold recovery process flowsheet. The case study was selected as an example of an ore with a marginal gravity gold content, which makes the value of a gravity circuit difficult to quantify. In this instance the value of leveraging a significant knowledgebase of operating gravity circuit performance to support the decision making process was demonstrated. This case study analysis serves as a useful demonstration of best practice methodologies supporting decisions to include or exclude gravity recovery in a gold recovery process flowsheet.CITATION:Giblett, A and Afewu, K, 2015. Do we need a gravity circuit or not? A case study in applying best practice, in Proceedings MetPlant 2015, pp 288–295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By Arnold C. Love

This report discusses current research by the U.S. Bureau of Mines on the effects of whole-body vibration (WBV) and shock on underground mobile equipment operators. The highlights of a comprehensive literature review of WBV, shock, and seating are presented. Factors discussed include health and physiological effects, comfort, performance, and fatigue. Vibration data were collected from shuttle cars and ramcars at several underground coal mines in Pennsylvania, Ohio, and Illinois. The data were formatted so that they could be used to drive the Bureau's motion platform, and to compare them with ANSI S3-1979, Guide for the Evaluation of Human Exposure to Whole-Body Vibration. Human subject testing in the Bureau's vibration research laboratory evaluated the effects of two different seat angles and of the presence or absence of vibration and of foam padding on heart rate, blood pressure, and subjective discomfort. Only vibration significantly increased heart rate and systolic and mean blood pressures. Vibration and a steel seat had a significant effect on subjective discomfort. The apparatus used for these tests and the experimental procedures are described in detail. Recommendations are made for additional research on the exposure of underground mining machine operators to WBV and shock.

Jan 1, 2010

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By L. You

Theoretical and analytical analyses of three mitigative measures- plane fitting method, trenching, and tension cable led to the development of a total protection plan to eliminate or reduce damages to the residential structures subjected to surface movements caused by underground longwall mining. The protection plan was applied to twelve residential houses and two external garages. The success rate is overwhelming. This paper describes the methods employed for protection and results of those case studies.

Jan 1, 1986

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By Hebi Yin

A two-dimensional multi-scale solidification model was developed to study the heat transfer, fluid flow, and grain growth occurring in the molten pool during the laser engineered net shaping (LENS) process. This model coupled the finite element method to calculate mass, energy and momentum transport in the macroscale with the cellular automaton technique to calculate liquid/solid phase change at the microscale. The validation of the model was performed by comparing the simulation results with experimental data from previously published works, showing good agreement in temperature distribution and the dendrite morphology (size and shape). The simulation results showed that Marangoni convection, caused by the temperature gradient along the pool surface, played a critical role in determining the flow pattern in the molten pool and exerted influence on the pool size and shape. It was also found that columnar dendrites can be formed, with dendrite arm spacings as fine as a few microns due to the high cooling rate during the LENS process. In addition, the influence of fluid flow on the dendrite growth in the pool was discussed.

Jan 1, 2010

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015

By H. L. Barwood

Luminescence excited by electron bombardment, or cathodoluminescence (CL), is a very useful tool in petrographic examination of rocks, minerals and ores. Differences in luminescence colors and intensities allow detection and delineation of mineral species and composition zones difficult to separate visually by normal polarized light microscopy. The cold cathode CL chamber at Indiana University is used with a binocular microscope that has interchangeable attachments for a normal film camera, a digital camera and a fiber optic spectrometer. This allows imaging of the specimens as well as limited spectrographic analysis of the emitted luminescence. The chamber on this CL unit is large enough to accommodate several thin sections, polished mounts, grain mounts or rock slices at one time. Luminescence petrographic techniques were used to study alkali syenites and carbonatites from the Arkansas. Alkali feldspars in the syenites reveal a history of growth, fenitization and replacement through color and intensity differences. Primary orthoclase luminesces bright blue and is often zoned with a duller blue overgrowth of microcline. Fenitization of the feldspars is demonstrated by dull to bright red luminescence and replacement veins of albite often have a bright yellow green luminescence. Late microcline and perthites from the syenite pegmatites have a dull yellow to orange luminescence. Easily visible on this background of feldspars are grains of apatite (yellow), fluorite (violet), zircon (greenish), sodalite (orange) and mosandrite (green). Complex pseudoleucite syenites from Magnet Cove, Arkansas show similar minerals but also include xenolithic quartz (violet), manganwollastonite (bright orange), benitoite (intense blue) and lorenzenite (green). Carbonatites from Arkansas contain a wide variety of calcite textures and intensities of luminescence. Grains of carbonatite in well cuttings are easily distinguished from sedimentary calcites by their complex “flame” luminescence and the frequent presence of euhedral apatite grains (yellow). Apatite crystals separated from the Arkansas River Valley carbonatites by acid digestion show complex zoning. The cores of these apatites are yellow luminescing due to CL activation by Mn enrichment while the rims are violet luminescing due to REE enrichment. Complex zonation between the cores and rims is easily visible using CL.

Jan 1, 2001

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

By J Bresnahan, D Kepert, R Murray, R Neroni

Stratigraphy of the Hamersley Province in Western Australia, featuring alternating units of banded iron formations and shales with contrasting electrical properties in a mostly gently undulating shallow-dipping layered geometry, is particularly favourable to airborne time-domain electromagnetic mapping techniques. Manipulated vertical cross-sections of modelled conductivity obtained from laterally constrained one-dimensional inversion of SkyTEM304 data enable the exploration geologist to interpret weathering profiles, shallow-dipping stratigraphy and steep structures, all of which are crucial aspects of bedded iron ore deposits genesis models.The Cobra Project is located 14 km east of the NNW-trending Menindee Fault Zone, which defines the western margin of the Hamersley Province, Western Australia. The region comprises an extensive plateau of Brockman Iron Formation cut by a series of horst and grabens with a regional dextral strike-slip component. The 150° striking horst and grabens and associated 060° striking conjugate faults have approximate frequencies of 400 and 2000 m, respectively, and control the bulk of the iron mineralisation. Syn to late 150° trending dykes in part intrude the faults.In the Cobra region, elucidating the structurally dislocated stratigraphy without closely spaced drilling is very challenging. Geological mapping is hindered by the paucity of mappable stratigraphic markers within the banded iron formations and kinematic indicators. Airborne magnetic and remote sensing data sets highlight the dense lineament network, but provide limited assistance in quantifying relatively small apparent displacements, or distinguishing faults from dykes with reasonable confidence.Interpretation of modelled conductivity cross-sections generated from laterally constrained one-dimensional inversion of airborne electromagnetic method (AEM) data offers invaluable insight where the quality of mapping or drilling is wanting. Subsequent targeted field checking and infill drilling validated the geological model interpreted from the integration of these data sets.The AEM technique alone cannot decipher the complex geological environments often present in the Hamersley Province but can facilitate effective iron ore exploration by focusing precious field time and assisting structural and stratigraphic interpretations in areas with sporadic and shallow geological data.CITATION:Murray, R, Neroni, R, Kepert, D and Bresnahan, J, 2017. Using airborne electromagnetics to solve a structurally complex geological puzzle in the Hamersley Province, Western Australia, in Proceedings Iron Ore 2017, pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.