Search Documents

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

THE following short paper on the Blair Athol coal-field will no doubt have a twofold interest to members from the fact that its main seam, known as the "Big Seam" of a maximum thickness of 91 ft without a band, is unique, being probably the thickestseam of high-grade clean coal yet known, and also because of the interesting problem it presents the colliery engineer-viz., which system of mining is the best to secure the highest economical extraction.Location - Blair Athol is a mining township in Central Queensland, situated at an altitude of about 1100 ft. above sea-level at the end of a branch railway line 74, miles from Emerald, on the Main Central Western line, and 240 miles by rail from Rockhampton.Geology - The coal-measures appear to lie in a shallow basin of about four or five square miles in area, surrounded on all sides by slates and schists, which are overlaid oh three sides by alluvial deposits of up to 150 ft. in thickness, and on the fourth by a thick basalt bed, as yet unproved, some miles beyond which the auriferous slates outcrop. These alluvial deposits have been largely worked in years past and gave high gold returns, the chief diggings being Clermont and Macdonald's Flats in the south, the Springs and Black Ridge in the north-east, and Yankee Creek and others on the west. The surface of the coal-fields may be described as unbroken, but undulating, with gentle southerly dip, the watercourses opening out into wide flats. The absence of creeks or deep gullies accounts for no outcrops being visible on the surface, and the coal-measures...

Jan 1, 1918

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By N. E. Mkadmi

Backfilling increases the stability of underground stopes and may help reduce the environmental footprint from the mining operation. The barricades holding the backfill in place must be designed to prevent failure based on the total and effective stress states, which depend on fill properties, stope geometry, and filling rate. This paper presents results from a numerical study aimed at analyzing the stress states associated with the response of paste backfill following stope filling, with an emphasis on the short term behavior. The simulations illustrate how stresses evolve with backfill drainage and filling rate in a vertical stope.

May 1, 2011

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By Paul Russell, M. M. Kimberley, Erick F. Welland, Louis Cope, C. C. Mosher, William M. Shepard, William C. Larson, Graham Closs

Exploration activities in 1980 felt the effects of unstable economic conditions and oscillating metal prices. In the cyclical, boom-or-bust precious metals and uranium markets, precious metals activity flourished and uranium was definitely in a slump. By November last year, the price for vellowcake was down nearly $20 from two years earlier. Many mining and milling operations closed, particularly in Wyoming, New Mexico, and Colorado. Decreasing emphasis on nuclear power continued to impact the market, as did the Three Mile Island accident of 1979. Earlier forecasts estimated that 10 to 12 reactors would be ordered per year by US utilities throughout the 1980s, but current forecasts suggest that it may be 1983 or 1984, or even later, before any new US plants are ordered, according to Thomas A. Boyden, vice president of Nuclear Exchange Corp. "Without those new plants, the consumption loss to industry is 4 to 5 million pounds (1.8-2.3 kt) of uranium per year. The cumulative loss to the industry is currently estimated at 25 to 30 million pounds (11.3-13.6 kt)," Boyden said in a May 1980 presenta¬tion. Despite the plunging market, there were a few notable uranium explora¬tion programs: •Exxon expanded uranium exploration in New Mexico, where the company reportedly took preliminary steps toward acquiring mineral rights to a 22-km2 prospect, 19 km south of Santa Fe. • Mountain States Resources began the second phase of an exploratory drilling program on its Sinbad/ Solo prospect in Utah. • Also in Utah, Cotter Corp. drilled its first exploratory hole in the Dirty Devil River district. Exploration for precious metals in 1980, however, appeared to tend toward the opposite extreme. High prices sparked near feverish searches in Alaska, California, Colorado, and Nevada. Numerous mines abandoned years ago were revived with some signs of success. Significant gold finds were reported in California and Nevada: • Homestake Mining Co. announced a gold discovery in California estimated to contain over 5 Mt with an average grade of about 5.8 g/t. Because the deposit consists of finely disseminated particles not visible to the eye, many speculate that prospectors bypassed the area during the 1849 California gold rush. • Newmont Mining Corp. discovered two gold ore bodies-Maggie Creek and Gold Quarry. Maggie Creek reportedly contains an estimated 13.7 t of gold in 4.3 Mt of ore, and Gold Quarry contains about 31.1 t of gold in 9 Mt of low grade ore and 2.3 Mt of higher grade ore. Highlights of this year's exploration review include articles on the modest growth recorded in geophysical activity, technical developments in exploration geochemistry, the variety of new instruments being tested or made available for exploration, and a state-by-state exploration review for the year.

Jan 5, 1981

By A. Fisne

Outburst of gas, coal and rock can be defined as sudden release of coal and rock accompanied by large quantities of gas into the working face or other mine workings. The outburst events appeared rarely in some metal mines has generally occurred in salt and coal mines especially bituminous coal mining. The most important factors that influence the occurrence of outbursts are gassiness of the coal seam, tectonics, properties of the coal and rock and vertical and lateral stresses occurring in the seam and or rock or part of the coal seam. This paper describes the problem of gas and coal outbursts in underground coal mines. The outburst events occurred in Zonguldak Coal Basin located on the Black Sea coast was investigated since 1969. Geological and gas conditions of Zonguldak Coal Basin are described. The incidents are analyzed statistically with the criteria such as amount of coal and gas outburst, depth of workings, effect of tectonism, thickness and inclination of coal seams.

Jan 1, 2012

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

By Fernando Romero Lage

The purpose of this paper is to analyze detailed crushing and screening configurations and the interrelationship as they relate to mass flow balance, operating efficiency, plant availability and final production. The entropy of ore bodies limits the standardization of crushing and screening plants, however, consideration for a continuous and sensible assessment of the mass flow balance of the circuit will yield the best achievable results. Since energy costs have continuously risen in the last few years, it is imperative that these circuits offer low power requirements and low operating expenses. The paper will detail how the efficient implementation of continuous mass flow balance in the application of crushing and screening plants will generate quality improvement and process improvement, which will translate into bigger production and energy savings.

May 1, 2010

Analyses of scheelite from all the known scheelite fields in the South Island of New Zealand have shown that the scheelites are essentially molybdenum-free. The scheelites are almost stoichiometric CaWO4, except for some strontium replacing the calcium, with a maximum of 0&#183;92 per cent SrO. Variation in strontium content appears to be&apos; related to the metamorphic grade of the enclosing rocks.

Jan 1, 1970

By Tomek Ulatowski

INTRODUCTION In 1974, Industrial Miners Mexico, S.A. (IMMSA), agent for the borrowers, was the largest privately-held mining, smelting, and refining company in Mexico (accounting for 32% of Mexico&apos;s nonferrous metal and coal production in 1974), the fourth largest company in terms of sales, and the second most profitable company in Mexico, excluding government wholly-owned and operated industries. The company was engaged in the mining, smelting and refining of coal, copper, fluorite, gold, lead, silver, zinc and related by-products for domestic consumption and export. A combination of favorable factors led IMMSA to propose an investment plan amounting to US$286 million for 1974 through 1978, of which US$150 million was to be financed. These factors included: Substantial profits in 1973 and 1974 Positive near-term outlook for metal prices Success of the reinvestment program in increasing productivity Substantial additions to proved reserves during 1973-1974 and Fiscal incentives provided by the Mexican government to stimulate investment in the mining industry. The primary purpose of the investment program was to construct a new electrolytic zinc refinery and to expand and modernize many of the company&apos;s existing mining and refining facilities. THE BORROWER Company History Compania Miners Mexico, S.A. was incorporated in the city of Monterrey in 1918 as a wholly-owned subsidery of ASARCO Inc. (formerly American Smelting and Refining Company, New York) for the purpose of mining and processing non-ferrous metals and related products. In compliance with the Government&apos;s Mexicanization program, ASARCO Inc. divested itself of 51% of its equity in Compania Miners Asarco, S.A. on June 30, 1965. Subsequently, ownership in the divested share was apportioned as follows: 15% ownership in Compania Miners Asarco, S.A. to a group of private investors, and 36% in trust for subsequent public sale. The company&apos;s name was changed to Asarco Mexicana, S.A. in 1965. Mexican ownership in Asarco Mexicans, S.A. was increased to 51% in 1967, following the purchase of the 36% share ownership held in trust, and then to 66% in 1974 when ASARCO Inc. divested itself of an additional 15% of its holdings in Asarco Mexicans, S.A. Following its 1974 divestiture of 15% of Asarco Mexicans, S.A., ASARCO Inc&apos;s ownership in Asarco Mexicana, S.A. was reduced to 34%. In 1974, the company changed its name for the second time to Industrial Miners Mexico, S.A. (IMMSA). Fiscal Agreement IMMSA entered into a fiscal agreement with the Mexican government in 1969. The agreement, which was renewed in 1974, provided for 100% of the production and export tax corresponding to the federal government with a minimum of 50% of the amount refunded to be reinvested in fixed assets. Further, the agreement permitted the company to

Jan 1, 1985

By Eder Salazar

El presente texto describe la optimización de la productividad en la empresa minera a través de la mejora contínua en la cadena de valor en SMEBSAA, los siete pasos de la calidad, proceso de mina, planta, soporte y la cuantiificación de dicha mejora en la cadena de valor en SMEBSAA. Asimismo, la implementación de los diversos sistemas de gestión refuerzan los resultados, siendo el Sistema de costeo basado en actividades el gran agrupador de toda la información de los módulos: Logístico, Control Patrimonial, Orden de Servicio, Planillas y Contabilidad.

Sep 12, 2005

Vale Inco?s Coleman Mine 153 Orebody is a narrow vein deposit with a dip that varies from 30 to 70 degrees. It has a strike length of 1200-feet and the current mining extends from the 4250 level to 5100 level. The primary mining method is mechanized cut-and-fill although drift-and-fill is also used in wider sections of the ore zone. The ore body is divided into six main mining horizons with an average of three mining blocks on each cut. There are some interesting rock mechanics challenges related to mining upward from the 4550 level and these challenges are increasing as the mining front progresses toward the 4400 level. The mining of the 4550 block is currently at cut 13 whereby the crown pillar thickness is approximately 60-feet. Significant factors including increased stress levels in the crown pillar, the change in the orebody dip at this level and a recently indentified geological structure in the footwall, have all combined to introduce seismic activity in the footwall of 4550 level. Closer studies revealed a consistent trend of seismicity that was further examined with core logging and Acoustic TeleViewer technology. The data from these assessment tools disclosed a geological structure that is influencing the mining environment. This paper reviews the seismic analysis for the 4550 level mining zone and the subsequent procedures used to locate the new geological structure. The paper also discusses the key mining practices used to successfully mine cut 13 of 4550 level and briefly reviews the studies that are underway to up-date the mine design for continued extraction of high-grade ore in a safe and productive manner.

May 1, 2009