Search Documents

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

During the past decade, the miner-al industries have been faced with an increasing shortage of engineers. The point has now been reached where the shortage may be termed critical. This shortage may be attributed directly to declining enrollment in the mineral science programs offered by the universities on this continent. Although the reasons for declining enrollment are undoubtedly many, two major hypotheses may be postulated. The first is that high-school graduates are either unaware of the mineral industries and the opportunities in them or that they are aware of them but have somehow obtained a false image of their true nature. The second is that they are aware of the true nature of these industries and the opportunities they offer but find them exceedingly unattractive. The problem of dwindling enrollments has, in recent years, been subjected to a concerted attack by the industries and professions concerned. However, their efforts to date have been based essentially on the first hypothesis. Sufficient results are now available to suggest that either the methods of attack are inappropriate

Jan 1, 1965

By G. L. Oldright

The first Report of Investigations of the present series (No. 4562) was on the fundamental properties of lead compounds, and the manner in which they set limits to the richness of lead products treated in the usual sintering-blast furnace units. These properties of the compounds were emphasized, as' it was desired, also, to learn the limitations of smelting the same compounds in present ore hearth practice; the hearth has a competitor in these "usual" units, even with the rich lead feeds best adapted for the hearths. Operating conditions that were followed in older metallurgical processes, when rich products, were treated, were outlined. The second report of the series (R. I. 4563) was on the development of the ore hearths of the types now used in the Tri-State from the viewpoint of the features, functions, and dimensions of the earlier hearths that had been most changed. Experimental data, for both well and poorly desulfurized charges being considered, were given to show the relative changes in the sizes and compositions of the charges after they were added to the ore (Scotch) hearths. A general picture was given of the charge column and of the conditions prevailing there when the operation was satisfactory. In this third paper, the composition of the gases prevailing in the charge column at various elevations will be correlated with what has been learned of the nature of the charge column in order to trace the steps of operation by which lead sulfide is converted into metallic lead. The metallurgical factors that govern operation and the lines along which improvements may be made will be noted.

Jan 1, 1949

By Victor E. Kral

The Valery fluorspar deposit , also known as the Hamilton deposit , is northeast of Lovelock and 4 miles by poor dirt road east of U. S. Highway 40 . It is in the Humboldt Mining District , on the west side of the Humboldt Range , at an altitude of 6,000 to 6,500 feet . The property was examined by the Bureau of Mines on February 83/ and April 8 , 1944.4/ The last examination was made with an engineer of the Geological Survey.5/ Exploring by means of trenches , cuts , shaft sinking , coyote holes off the shaft , and a small amount of prospecting with short drill holes , was begun in January 1945 and was completed June 30 , 1945. An engineer6/ of the Geological Survey visited the property in April and again in June 1945 to complete a topographic map of the area and to note the results of exploration by the Bureau of Mines . Only minor surface exploring had been done on fluorspar occurrences previous to the Bureau's work . No mining equipment or living facilities are on the property .

Feb 1, 1947

By W. A. Gow

"In January of 1964, a group known as the Canadian Gold Metallurgists was formed with the backing of the managers of most Canadian gold mining operations. This organization is composed of about thirty mill superintendents of Canadian gold milling operations where the cyanidation process is in use, and one member from the staff of the Mines Branch, Department of Energy, Mines and Re-sources, Ottawa. The aim of this group is to bring together gold mill operators, and research and development people from both industry and government for the purpose of discus-sing common metallurgical problems, and deciding on what operational R and D efforts can be made to help solve these problems. Since the conception of this organization, this approach taken by the gold industry to the study of metallurgical problems has resulted in benefits to all operators, both by assisting them with problems peculiar to their own individual operations and by providing developments of general interest to the industry.This paper describes events leading up to the formation of the Canadian Gold Metallurgists, and how the group has operated since its formation. Examples of progress made toward the group's objectives are given, and possible future programs are discussed."

Jan 1, 1968

By Kunihiko Takahashi, Gjergj Dodbiba, Hisayoshi Umeda, Toyohisa Fujita

"An increasing number of mobile phones is increasing the number of the discarded mobile phones. Many efforts are thus being made to collect and recycle these devices. This paper is a short introduction of the recycling system of precious metals from the discarded mobile phone, currently available in Japan. Moreover, an attempt has been made to compare the energy recovery and the mechanical recycling of plastic wastes from the discarded mobile phone. The assessment has been carried out in the context of the life cycle assessment methodology (LCA). The environmental impact of each option was assessed by calculating the following impact indicators: depletion of abiotic resources (ADP), and global warming potential (GWP). 1. Introduction In 2003, the demand for mobile phones was increased since the camera was included in a mobile phone and the 3rd generation of mobile phones was introduced. In turn, the number of discarded mobile phone is rising sharply. Generally speaking, all the metallic parts of mobile phones can be recovered and recycled by using smelting and purification techniques. The recycled materials are then used to fabricate other new products."

Jan 1, 2008

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By M. W. BERNEWITZ

DURING my recent extended visit to Australia and New Zealand, these notes on oil and gas prospecting in that part of the world were compiled from recent reports-press and government, from conversation with one of the financial leaders in the search for oil, and from personal observation of operations of the principal importers, blenders, and distributors of oil products; also from the astonishing testimony given by them to the Petrol Commission. Australia and New Zealand have practically no petroleum production beyond a few thousand gallons a year from wells in the latter Dominion. Everything is imported, Table 1. showing the quantities for 1929-30 in Australia and for 1930 in New Zealand,

Jan 1, 1934

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

[lllc purpabr at thla report Vd, Lu JeLermlnr the health ar1J sdfet?; Nene11Le a octatc?J ultll Lne oar L.t support Ydlll ..up.I,ated lu dltetllative cupPurt svsLem, larrellLty hcle.g uaeJ af the Len,::rat 1, UI.Jlng 11-al tl. .1 a d 1 c L V h S LIdl'. L dal. I -ten- lu L he tt I .. L'., etuJ I e. 11'? L_1,1'1,11 .Jtd.. it, ..urn,at'l core ,LuJICCill JhLdll, an.: ...,La -IL .utia_tel .an LI?r oar of -l: l,.!rl .a..a. Ma terI.I auJ ...11,mc[Ii -ldla,tutcle 11. LI.ac .uwIttIca Welt a, a.. V.alte,, L.. .:Ltail, ..,,L., uI. LuClu,alug) Lelll anci ur devel?puJ I.,r Cul r1 , all. ...~.,rLrI Vt,ILt 1.'ere ~e,1C L? .Lher Gentiaii m111cc t, UL.-rye a Variety o. a rL vyl I pp.1Ca:t..n:. 'a.la IrL ..,_wLeiti, Iapl,.III ,tall ~,..:. IL all, maLertdl c1,arait-erlstIcs, JIRICn,IUIIe. and laden ul1.1 ILc rrgatrelaeuls. ,1 r.? p.'rt .a pro-1Jd, labor rep altrlarnts Jdta and illtlitI ieS tie l,ealtll d?J ,atetV ISSUC ,u-1aled Wit su furl Wall a an, CJl,wttuctSOn, I'aLentiaI appll.at1ou:. Ior support Walt, ,a,. , a, sdV.u,L111 .., u.1 retreating lungval1, single -t r-, roar al,- pi r. [,-+ln, anJ SuhIU..,Ina, Sill] b1OpplllgL ale 1:111neated aid al? e.aIWRac AS Sddemcni LV pre,C'IIL..: .,f LI. Clabllhty r+t rlul,I.,y111I? ulg4,rt .I Le.l,lwlug,. Lr i,,,rCASC Lllc rtCVLLrS rat, u., retrc.+tlnp .unui.,11? ur L., elply, A d v Ctnp IuI-,wall in uer;-!y iy1ng seam, . 11111.a1L .a1,.'iI1.-I,.. nr S.IU1tIVlil a1 milItlI; Lust, La LIldnt;2S L.~ gey support Vait Id tdmcLera la dlaa presents,.]

Jan 1, 1980

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 196'), under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures Dr. Henry R. Linden, Director, Institute of Gas Technology and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 1965, under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures. Dr. Henry R. Linden, Director, Institute of Gas Technology, and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

By Paul Miranda, Corby Anderson

"The Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently obtained a Mineral Liberation Analyzer (MLA). CAMP has utilized the technology for several projects with excellent results. The MLA is able to both analyze size and quantify mineral phases. Therefore, the MLA is becoming the Sherlock Holmes of the mining and metallurgical industry. For this presentation, four projects have been evaluated and data was collected using the MLA. The first project involved tungsten mine. Previous mining practices have yielded poor tungsten results and recoveries. By using the MLA, tungsten mineral phases, along with possible contaminants, were verified and the results used to try to increase overall tungsten recoveries. The second project evaluated a molybdenite/chalcopyrite concentrate with surprising results. The third project is a silver project. Initial flotation scoping tests were performed by attempting to separate silver from gangue material. Because of the poor recovery results (less than 5%), MLA was used to determine possible scenarios for increasing silver recovery. Finally, the last project involves gold evaluation in tailings. For all projects, MLA application results will be presentedand discussed.INTRODUCTIONThe Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently received a software add-on to a scanning electron microscope (SEM) located at Montana Tech. The Mineral Liberation Analyzer (MLA) technology was developed by Dr. Ying Gu of the JKTech Center of the University of Queensland. Since August 2006, CAMP has received and processed over 50 samples. These samples include a total mineralogy of tungsten ore samples, gold tailings, lead zinc tailings pile, molybdenite concentrates, copper concentrates, as well as others. During analysis of these received samples, the technology allows the samples to be quantified mineralogically with some surprising results.For analysis, the samples were initially sieved between 170 to 200 screen sized mesh. This ensures that received samples mineral size is fairly uniform. The samples are then placed into epoxy and allowed to harden. Next, the samples are polished and carbon coated for MLA analysis."

Jan 1, 2007

By Robert A. Clifton

It seems probable that more and more minerals will be used in plastics as time goes on. This must occur because the minerals will; aid in processability, enhance the engineering properties, reduce the cost, and above all conserve large amounts of petroleum based chemicals. This paper examines the advantages and disadvantages of using the minerals and the ability of the domestic minerals industry to support this possibly very large undertaking. In the author's opinion, it can. This talk is excerpted from a forthcoming Bureau of Mines Information Circular.

Jan 1, 1985

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982