Search Documents

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By Drew Sinha

Success of the environmentally benign semiconductor manufacturing depends on the cost-effective integration of the principles of reduce, recover, reuse and recycle from source material to final product disposal. Increasing demand combined with current shortage of polysilicon provided unique opportunities to recover the silicon waste, caused by various defects, in wafer manufacturing process. Current practices relating to recovery and reuse of waste silicon produced, from crystal growth process to finally polished and epitaxially deposited silicon wafer, at Mitsubishi Silicon America is presented. Future plan to recycle the process generated silicon fines produced during the intermediate steps of the wafer manufacturing process such as grinding, slicing, lapping and polishing is also discussed.

Jan 1, 1998

By Fang-Qui Zu

Understanding the nature of liquid structures and properties remains an open problem for many fundamental and applied fields such as materials sciences and processing. And as well known, there is no other defined phase line above liquidus (TL ) in phase diagrams of ordinary binary systems. However, via different experimental resorts, our research results on over 30 metallic melts including alloys and elements show a novel physical image: temperature induced liquid-liquid structure transition (TI-LLST) can occur hundreds of degrees over TL. On the other hand, the solidification behaviors and structures out of the melts experienced TI-LLST are distinct from those out of the melts before TI-LLST. In this presentation, some characteristic aspects of the TI-LLST and the effects on solidification behaviors and structures are briefly summarized, and the pertinent rules and mechanism are also analyzed.

Jan 1, 2009

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By K. S. Izbakhanov

The Chimkent Lead Plant was constructed in 1934 and since that time has undergone many revisions. In 1975 the slag fuming operation was changed from pulverized coal to natural gas fuel. In 1981 the slag fuming furnace water jacket system was converted to evaporative cooling with high pressure steam production. The impact of these changes and the method of their application are described.

Jan 1, 1990

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By A. Buzaianu, P. Motoiu, G. Popescu, C. A. Popescu, I. Rusu, A. F. Olteanu

"In recent years, the recycling magnesium metallurgy has developed new types of alloys, some of which exhibiting special electrochemical characteristics. Their application has found a fertile field in the energy conversion technologies. The paper introduces some technologic data on the recycling of aeronautical parts and scrap materials generated from the disassembling of magnesium alloy components, attempting to also solve the recycling of magnesium painted parts. The approach is meant to establish a superior quality method for recycling discarded parts or the excess of re-melting material in order to reduce environmental impact and costs. Magnesium-base alloys used as anodic materials are characterized by a high uniformity of the structural properties as well as by superior electrochemical performances, as compared to the ""classically"" used materials: Zn, Pb, etc. In nonconventional applications of magnesium alloys used as sacrificial anodes working in seawater, special alloying elements contribute to improving anodic processes. The influence of these alloying elements on magnesium sacrificial anodes was studied. It was found that the use of recycled materials in anode manufacture could reduce the Mg alloy cost by as much as up to 75% of the cost for virgin material, including the costs for the entire sequence of collection and transportation from a molding factory to a refinery, re-melting and composition adjustment.1. IntroductionMagnesium alloys are valuable materials because they exhibit low density, good forming and machining qualities, particular electrochemical properties and have a high recycling potential. There exists a false idea about the high costs of the use of magnesium alloys, partly justified by the lack of secondary materials suppliers and the insufficient knowhow in the diverse user industries to provide for an efficient substitution of conventional magnesium alloys for multipurpose applications. These circumstances have lately spurred the magnesium industry to develop new alloys and coatings and to improve processing techniques [1]. As a result, magnesium supply has greatly expanded and so have the research and development efforts to achieve complete recycling of Mg alloys.In consumer markets, magnesium is frequently selected because it helps reduce enery consumption. For example, an equal volume part made of magnesium is 23% the weight of a steel part and 64% the weight of an aluminium part."

Jan 1, 2008

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste-free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the 'solvent' or 'transport agent' and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

By B. Erik Ydstie, Dimitrios I. Gerogiorgis, Sridhar S. Seetharaman

"Carbothermic production of aluminium is an important alternative to electrolytic processes and has in fact been identified several decades ago as a potentially feasible and profitable process. The cornerstone principle is to take advantage of the endothermic reduction reaction between carbon and alumina instead of resorting to extreme amounts of electric energy to ionize and reduce aluminium oxide to aluminium. Electric energy is necessary only for heating purposes.The present study focuses on constructing and solving a steady-state electrothermic model for obtaining the spatial distributions for electric potential, electric field intensity and temperature. The complex issues of reaction kinetics and multiphase flow are handled by an approximation and are not addressed at the present stage, due to the lack of complete validated models. Because of its inherent complexity, the reaction slag is considered a pseudohomogeneous layer.An electrothermic simulation encompasses important research challenges, due to the limited knowledge of thermophysical properties for high-temperature multi component molten slags. Therefore, thermophysical property modeling and a systematic compilation of published data is a necessary and major first step towards enhancing understanding of the process fundamentals. Models are obtained by analyzing measurement data from numerous literature references for the density, viscosity, thermal and electrical conductivity and specific heat capacity of the slag.The electric potential, field intensity and temperature distributions obtained reveal interesting maxima which indicate localized superheating and lead to important engineering conclusions. The temperature profile calculated will serve as the foundation for the flow problem solution. This computational study will form a basis for future research towards combining the scopes of microscale CFD modeling and mesoscale process modeling into a unified modeling approach."

Jan 1, 2001

By Shaik Jeelani, Mahesh Hosur, Esperidiana A. B. Moura, Rejane D. Campos, Emilia S. M. Seo, Kerry Kirwan, Francisco R. V. Díaz, Maria Sotenko

The use of natural fibers with polymeric resins has spread rapidly. In order to improve the mechanical properties of material, in this work, two variables were used: mercerization and electron beam irradiation. This paper describes the preparation and characterization of biocomposites that were prepared in two different routes using green high density polyethylene (HDPE) and Brazil nut pod fiber (BNPF): the first was to irradiate the composite with 150 kGy and the second was to irradiate the matrix with 15 kGy followed by composite preparation. In both cases mercerized and non-mercerized fibers were used. The irradiation process was carried out using a 1.5 MeV electron beam accelerator, at room temperature and in the presence of air. The material was characterized to evaluate the effect of treatment on mechanical properties of material.

Jan 1, 2015

By Robert Vidal

The performance of a laboratory-scale cell for the electrolysis of an aqueous chrome alum solution was studied. Electrode potentials, pH, and Eh were recorded. An optimum catholyte pH of about 2.5, consistent with information from the literature was observed. Values exceeding this range resulted in a precipitate formation and are detected by wavering cathode potentials. The role of anodically produced dichromate ions was investigated by chemical analysis. It was found that the steady state concentration of dichromate ions varies inversely with fluid flow from catholyte to anolyte. This concentration was also reduced with the use of precious metal coated titanium anodes.

Jan 1, 1994

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Maija-Leena Metsärinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high (up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro-scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEMIEDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Maija-Leena Metsiirinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high ( up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro- scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990