Search Documents

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By M. Girgis

The behavior of arsenic III during electrolytic refining of copper in acidic copper ?sulphate electrolytes was studied by different electrochemical methods such as, linear potential sweep, cyclic voltammetry, chronoamperometry and chronopotentiometry. The study showed that arsenic behaves as a depolarizing ion and has a deleterious effect on copper deposit. Three substrates; Pb, Cu and Ag were used during the refining process and the electrode kinetics were found similar for both Cu and Pb electrodes while a little difference was found for the Ag electrode. A microscopic study by scanning electron microscope was undertaken to show the influence of arsenic on deposit's morphology. Surface analyses of the deposit were carried out by some electronspectroscopic techniques such as Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). The results showed that arsenic coexists with copper deposit at potential?~ -0.25 V.

Jan 1, 1987

By H. Hahn, B. H. Kear, K. Kan, S. C. Danforth, G. Skandan, W. Chang

"A new chemical synthetic process for the production of non-agglomeratednano structured ceramic (n-ceramic) powders, starting from metalorganic precursors, is described. The process combines rapid thermal decomposition of a precursor/carrier gas stream in a hot tubular reactor with rapid condensation of the product particle species on a cold substrate. Critical to the success of this Chemical Vapor Condensation (CVC) process are (1) a low concentration of precursor compound in the carrier gas, (2) rapid expansion of the gas stream through an uniformly heated tubular reactor under a reduced inert gas pressure of 1-35 mbar, and (3) rapid quenching of the gas phase nucleated clusters or nanoparticles as they exit from the reactor tube. A wide variety of metal organic precursors is available commercially, all of which can be utilized in the CVC process to produce n-ceramic powders, including single phase, multiphase and multicomponent systems.The CVC process has been used to synthesize non-agglomerated n-SiCxNy and n-ZrOxCy powders, with controlled particle size in the range 2-20 nm. Heat treatment of the assynthesized n-powders in various high purity gas streams causes compositional and structural modifications, including particle purification and crystallization, as well as transformation to a whisker-like morphology. Thus, as-synthesized amorphous n-SiCxNy particles transform to (1) cubic n-SiC particles, when heated in flowing argon at temperatures> 1350 °C, (2) hexagonal n-Si3N4 whiskers, when heated in flowing NH3IH2 at 1400 °C, and (3) cubic nSiC whiskers, when heated in flowing H2 at 1400 °C.Non-agglomerated n-ceramic powders form uniformly dense powder compacts by cold pressing, which can be sintered to theoretical density at temperatures as low as 0.5 Tm' For example, full densification ofn-Zr02 powder compacts under free sintering conditions can be achieved at 1125 °C."

Jan 1, 1994

By Guo Chen, Yifeng Shi, Xiaobiao Shang, Nanshang Shen, Bangqi Zhang, Jinhui Peng, Junruo Chen

"The energy is introduced directly into the volume of the honeycomb ceramic regenerator due to the complex interaction of microwaves with minerals in microwave gas heating system. A three-dimensional numerical model is developed to simulate the electromagnetic field by solving Maxwell's equations using finite-difference time-domain method. Computational result is presented for the microwave power absorption of the regenerator. Effects of the dielectric constant and the effective loss factor on the microwave power absorption in the regenerator are studied as well. Numerical results show that the heating pattern strongly depends on the dielectric property of the regenerator. The demonstration of the model of electromagnetic field distribution can be applied effectively and efficiently to optimize the fundamental parameters in the microwave heating processing.IntroductionIn recent years, microwave energy has been utilized in many fields, such as food processing, chemical engineering and mineral processing [l]. In contrast to conventional heating, where heat is transferred from a surface to the interior, microwave energy is introduced directly into the volume of minerals due to the complex interaction of the microwave with the mineral. Based on volumetric heating effects, microwave heating has several advantages such as pollution free, rapid heating technique, internal heating, high efficiency over conventional heating [ 1-4]."

Jan 1, 2013

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002

By Devon A. Hannan

Thermodynamic modeling calculations were undertaken for the recovery of mercury from HgTe using a vacuum retort reactor. However, discrepancies were noted in the available thermodynamic data which introduced uncertainty in the model results. Consequently, a series of transpiration experiments were first undertaken on the thermal decomposition of HgTe into an inert carrier gas stream according to the following reaction: HgTe(s) Hg(g) + Te(s) From the measured weight loss of the HgTe samples, the Gibhs free energy change for the above volatilization reaction was determined as a function of temperature. The experimentally determined Gibbs free energy values were found to be approximately 30% larger (more posi-tive) than the values available in databases such as HSC Chemistry. By conducting a second-law analysis on the experimental data, the heat of formation of HgTe at 298.15 K and the en-tropyat 298.15 K were determined, which then formed the basis for a new database for the modeling calculations. The results of this study showed that HgTe was more stable at elevated temperatures than was generally indicated in the literature. The new database is given in a for-mat for direct insertion in HSC Chemistry. Using the new database, modeling calculations were conducted to examine the effects of the re-tort pressure and the molar ratio of purge gas to HgTe on the volatilization of mercury from HgTe. A diagram is presented that shows the minimum temperature for 100% volatilization of mercury from HgTe as a function of retort pressure for different molar ratios of purge gas (N2) to HgTe. For example, it was found that the minimum temperature for 100% volatilization could be decreased by 175 K, at a retort pressure of 0.05 bar, if the molar ratio ofN2 to HgTe is increased from 1.0: 1 to 100.0: I.

Jan 1, 2003

By Adolf Mikula

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of ternary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth, silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe element.

Jan 1, 2003

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Hong Liang-shi

Olivine lithium iron phosphate (LiFePO4) is considered as one of the most promising materials for lithium-ion secondary batteries because of its high theoretical capacity, low cost, good safety, benign environment and good cycle performance. In this paper, carbon-free and/or carbon-coated olivine lithium iron phosphate composite ultrafine powders were successfully synthesized from aqueous precursor solutions of (NH4)2Fe(SO4)2?6H2O, H3PO4 and LiOH?H2O by co-precipitation method. The obtained LiFePO4 or LiFePO4/C powders were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Their electrochemical performance was investigated in terms of cycling behavior. As confirmed by X-ray diffraction and scanning electron microscope, the material obtained by co-precipitation within the temperature range of 60ºC to 100ºC and then followed by moderate heat treatment are a single-phase olivine LiFePO4with the particle size of about 300nm. An improved carbon-coated olivine LiFePO4/C material was prepared by adding conductive carbon materials, such as glucose, activated carbon and acetylene black, into the precursor. The carbon dispersed in the materials increases the electronic conductivity of LiFePO4/C composite, and consequently, leads to high rechargeable capacity of the material. The carbon-coated material with carbon amount of 7.64%wt obtained from glucose has the first discharge capacity of 150.3mAh/g at the rate of 0.1C and 129.3mAh/g at the rate of 1.0C, respectively. After cycled for 50 times, the capacity retention rate is 95.13% at the rate of 1.0C in the voltage range of 2.5 to 4.3 V vs. Li/Li+.

Jan 1, 2006

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By Toshio Suzuki, Machiko Ode, Won Tae Kim, Seong Gyoon Kim

"The Ostwald ripening and growth and coarsening of the secondary dendrite arm are studied using a phase-field model. The phase-field parameters are obtained at a thin interface limit proposed by Kim et al. In Ostwald ripening analysis, the difference of the concentration due ·to· the curvature effect is shown. The third power of the average particle radius Rav is proportional to time and the ripening constant shows a good agreement with the value by Deppers et al. The particle radii distribution shows the transition behavior to attain a self-similar stationary shape. The growth and coarsening behavior of the secondary dendrite arm is also analyzed using a phase-field model. The estimated arm spacing and its dependence on time are in good agreements with experimental data.IntroductionThe ripening or coarsening process controls the microstructure during the late stage of solidification. The ripening phenomena are recognized firstly by the Ostwald [1]. The first quantitative analysis for the Ostwald ripening in the limit of vanishing solid fraction was provided by Lifshitz, Slyozov and Wagner (LSW) [2,3]. In their study, that the mean radius grows proportional to the cubic root of time and the size distribution of precipitations shows a ""self-similar"" shape are shown. Most of the studies for the Ostwald ripening confirm or predict these two general rules above. In case of finite solid fraction, the general rules are observed but the ripening constant is larger and the self-similar shape is wider than the LSW prediction respectively [4-6]. To analyze· the high solid fraction system, the theories that consider the solute field correlation are proposed [4,7-8]. In the theory, however, since the particle is treated as the point, the effect of the concentration field deviation from the monopole field should be taken into account. Recently the numerical simulation, in which not only diffusive transportation of solute but also convection effect is considered, has been done using a phase-field model [9]."

Jan 1, 2000

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By J. W. Perez

A simple exponential model has been developed (Perez and Aplan. Process Mineralogy, VI, 1986) to describe the fractional yield of a given species out of a locked assemblage: Fractional Yield of Species A = a e X/U where &apos;X&apos; is particle size and &apos;a&apos; and &apos;U&apos; are constants. In the present study, the general validity of this model has been further demonstrated. experimentally, for the liberation of coal and pyrite out of various raw coals and beneficiated fractions using a variety of crushing devices. Using data from the literature, the model is also shown to be applicable to the liberation of sulfide minerals out of ores.

Jan 1, 1987

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993

By William Petruk

A fully automatic image analysis system that consists of a microprobe, an energy dispersive x-ray analyzer, and an image analyzer was developed at CANME:I&apos; to determine mineral behaviour that affects beneficiation. The interlacing between the instruments permits automatic identification and characterization of minerals in samples of unbroken ore pieces and of mill products. Different types of information are obtained for minerals in samples of unbroken ore pieces than in samples of mill products, and are used differently. For unbroken ore pieces size distributions are determined for discrete mineral grains to predict a grind at which they might be liberated, and other measurements are Irade to predict the percentage of mineral that occurs as nonrecoverable grains. For mill products the minerals are analysed to determine percentages that (1) are free, (2) are likely to be recovered in concentrates, (3) are likely to be lost to tailings, and (4) could be liberated with regrinding. The image analysis data for mill products are processed by a mineral-metals balance program to determine the distributions of free and unliberated mineral grains at each point in a concentrator, pilot plant or bench test. For samples containing trace minerals, such as gold, an automatic search technique is used to scan the entire area of the polished section for the trace mineral grains. The identified trace mineral grains are characterized with regard to size, liberation, and other properties.

Jan 1, 1988

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

"This study investigated calcination behavior of one of the Turkish laterite deposits, which was recently found in Sivrihisar region. Representative limonitic laterite samples (1.26% Ni) taken from Yunusemre Karasivritepe and Kucuksivritepe location were first subjected to drying. Removal of chemically bound water and other volatiles were then studied, in detail. In the calcination experiments, temperature and time were the main experimental variables. Thermal treatment was conducted at the specific temperatures in 250 °C - 800 °C range. The weight losses due to elimination of chemically bound water and other volatiles were reported to be approximately 10 per cent of the weight of the ore. For the particle size used in the current work, 700 °C and 40 minutes were determined to be the optimum calcination temperature and time, respectively.IntroductionThe nickel ores that are economically valuable can be grouped into two categories: sulphide type nickel ores and oxide type nickel ores, namely laterites. Over all reserves in the world, 40% are sulphide nickel ores and the remaining 60% are laterites [1]. Pyrometallurgical nickel extraction from sulphide type nickel ores is conducted via matte smelting. More recently, laterite ore bodies have been subjected to nickel extraction. Depending mainly on the chemical composition of the laterite and the process economics, various extraction techniques have been implemented: pyrometallurgical route involves ferronickel smelting. High pressure acid leaching (HPAL) is the commercial method for hydrometallurgical nickel extraction, while ammonia leaching (CARON Process) is a combination of pyrometallurgical and hydrometallurgical processes [2]. With the improvements in these processes, it is predicted that laterite’s share in the world nickel production will rise to 50% in 2012, while it was reported to be 42% in 1,200,000 tons of annual production in 2003 [3]."

Jan 1, 2011