Search Documents

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

By Hamid Maleki

Results of geologic investigations, in-mine instrumentation, and numerical modeling are presented for two longwall mines in which pillars with large width-to-height ratios (8 to 9) are used. These investigations revealed that wide pillars unload when subjected to sufficient stress and that pillar unloading is influenced by geologic conditions. Field measurements in mine 1 clearly indicated load transfer from the longwall area toward the gate roads, resulting in pillar failure near the margin of a fluvial channel. Loads were shown to transfer to a harrier pillar (width height ratio equal to 9), contributing to progressive failure of this pillar. Unloading of the barrier pillar was associated with significant load transfer to the two-seam submains to the north of the harrier, contributing to roof falls, floor heave, and rib spalling within the submains. Stress analysis results addressed pillar peak strength and unloading behavior that was in agreement with the measurements and underground observations. Underground observations and stress analyses were completed before and after longwall mining near a six-entry submain in mine 2. This submain was intended to he used as a temporary bleeder and tailgate for a small longwall block consisting of one to two panels, depending on the development schedule in other areas of the trine and observed ground conditions. Numerical modeling using both elastic and inelastic pillar behavior for submain pillars with a width-to-height ratio of 8 was completed before mining began. Results indicated that pillar unloading was likely. During retreat of the first longwall panel, pillars unloaded. as evidenced by progressive rib spalling along the cleats, This behavior was mostly confined to the immediate face area, an observation that was in agreement with the modeling results,

Jan 1, 2000

By Shu Cheng

Abstract: Based on the consolidation theory of soil dewatering and land subsidence prediction methods in soil mechanics, preliminary analysis of surface subsidence and movement due to groundwater withdrawal was performed using the stochastic theory and the principles of effective stress and the method for subsidence prediction was derived, Surface subsidence due to coal mining was then superimposed to obtain the total subsidence. Keywords: land subsidence, rock and soil consolidation, stochastic theory, effective stress

Jan 1, 2002

By Mario G. Karfakis

Mining related subsidence is a major concern over abandoned shallow coal mines. Many of the subsidence prone areas are presently used or will be used in the future for residential housing development. Concern over mine subsidence is inhibiting the development of surface land uses on previously mined area. This concern prompted public officials to realize the need to develop guidelines which can be used to assess and reduce the risk of mine subsidence damage to building and other improvements. Subsidence and the associated ground movements must be defined before one can relate them to building damage. Surface movements resulting from underground coal mining occurs in two phases termed as: active subsidence and residual subsidence. Active subsidence refers to all surface movements occur in^ simultaneously with the mining operations, while residual subsidence is-that part of the surface deformation which occurs following the cessation of mining. Residual subsidence is the major concern over abandoned mine lands. The duration of residual subsidence is of particular importance from the standpoint of damage at the surface to structures built after the mine has been abandoned. Time spans during which surface subsidence may occur, vary markedly with the mining method being used. In total extraction methods, such as longwalls, subsidence is induced rapidly, beginning almost immediately after mining. Subsidence concurrent with coal extraction is desirable for a safe longwall mining operation. Usually subsidence is complete within a relatively short time. The remaining settlement occurs as residual subsidence due to the gradual compaction of the subsided ground. The relative proportion of the residual subsidence movements is dependent upon the presence of remnant pillars and roadside packs. rate of face advance and depth of workings. In partial extraction methods, such as with room-and-pillar systems. major occurrences of surface subsidence may be delayed for decades until the support pillars and/or the roof have substantially deteriorated and collapsed. The actual time involved depends on a number of factors such as the strength of coal, roof, and floor, extent of fracturing. presence of water, depth of workings, pillar size and percentage extraction. Consequently residual subsidence is more likely to occur over abandoned room-and-pillar mines. The following sections define subsidence over abandoned mines, review the proposed mechanisms, identify the controlling factors and examine the prediction methods.

Jan 1, 1987

By Alexander Kattner

Surface fractures in urbanized areas show the risk potential of near-surface mining. This kind of mining subsidence damage occurs mainly in areas where hard coal was mined near the surface with very little overlying rock strata. In North Rhine-Westphalia (NRW), the mining authorities assess areas that are at risk for caveins by means of envelopes constructed according to Hollmann and Nürenberg (1972). Drafting abandoned underground structures depends on the assessment of historical documents such as mine plans, mine titles, and operation plans of prior mines in this area. A research and development project establishing a comprehensive Geo Information System (GIS) for hazard prevention was undertaken in cooperation with the mining authorities of NRW. It aims to display the areas endangered by abandoned, shallow underground mines for the purpose of hazard prevention. A tool was programmed using ArcGIS as a result of this project. It is used to digitize underground workings from preserved mine plans, calculate outcrop lines of coal seams and display hazardous areas. In the future, a database of shallow mine workings will be established. The tool will be used for a systematical mapping of shallow workings and assessment of endangered areas.

Jan 1, 2011

By David P. Conover

The effects of stress distribution on pillar stability were evaluated through rock mechanics studies conducted in three underground room-and-pillar coal mines. Results of the three field instrumentation programs are presented to illustrate the use of borehole pressure cells to determine vertical stress distribution in coal pillars at various stages of mine development. Vertical stresses and stress changes are determined using methods developed at the Bureau of Mines. Measured stress distributions are compared against theoretical distributions and possible explanations for observed behavior are discussed. Results indicate that stresses and stress changes calculated from pressure cell data are inconsistent with theoretical values; however, the data are useful for qualitative evaluation of trends over time. Calculated values are found to be sensitive to coal properties and initial setting pressures of the cells.

Jan 1, 1989

A two-dimensional time-dependent analysis of a overburden-coal pillar-weak floor strata interaction problem is presented as a beam model consisting of a composite roof beam resting on multiple elastic foundations (pillars) underlain by a composite rock mass representing immediate floor strata. Several different material models may be considered for the immediate floor strata. The analysis can include all openings and pillars in a panel and permits bed separations in the roof composite beam. The model has enabled identification of the relative significance of different geometric and mechanical behavior parameters which govern the system. The paper presents the theoretical background for the model as well as its application to a mine in Illinois where surface and underground geotechnical observations have been conducted over the last two years.

Jan 1, 1988

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By David C. Oyler

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation, topping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented,

Jan 1, 2001

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain- softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OBAB) ratios of less than 5, interactions do not occur, and that for OBAB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OBIIB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

Jan 1, 2005

By Daniel W. H. Su

"This paper presents results from a recent study conducted to evaluate the effects of longwall-induced stresses and deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall mining abutment pillar can maintain mechanical integrity during and after mining operations. Successful designs would allow for the safe recovery of both coal and gas reserves. Major elements of this comprehensive study include: (1) modeling of rock movements to predict impacts on gas wells, (2) measurements of actual rock movements at the surface and in the subsurface, (3) measurements of actual impacts on test wells designed similarly to real shale gas wells, ( 4) comparison of modeling results to actual rock movements to validate the model, and (5) employing the validated models to evaluate various casing and cementing designs to minimize casing deformations and absorb longwall-induced strains along the intermediate and production casings.A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over an abutment pillar with 125-ft by 275-ft centers. The four test wells were drilled to a depth of 642 ft, or 42 ft below the Pittsburgh seam, and were designed like a real shale gas well, except that only three casings (namely the surface, water protection and coal protection casings) were installed in each well. Casing steel grades, wellbore diameters and annular spaces were purposely varied in each of the four test wells to evaluate the effect of different well designs. The four monitoring wells - one vertical extensometer and three in-place inclinometers (IPI) - were drilled to different depths to measure the vertical settlement and horizontal displacements as a result of longwall mining on both sides of the abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar mined by."

Jan 1, 2016

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By Ali Benbia

The paper shows results from the physical modelling of longwall excavations concentrating on the fracture pattern development above longwall panels. The modelling technique is briefly described and the detailed analysis of the fracture pattern is discussed. The physical modelling is particularly useful in visualising the caving process above longwall panels. This advantage has been exploited using the image analysis technique. Black and white pictures have been taken while the models are tested in successive stages and then enhanced and stored as binary images by scanning using an image analyser coupled with a video camera. These images are then processed using a custom C program which allows the discretization and characterisation of the fractures. This provides a valuable data base for further numerical and statistical analysis which subsequently may allow the assessment of the water inflow hazard to the workings. In this paper a sequence of different extraction thickness have been analysed using the technique mentioned above to show the effect of the extraction thickness on the fracture distribution and intensity.

Jan 1, 1993

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000