Search Documents

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By D. E. Winston

Roof falls are the major cause of fatalities in the, coal mining industry and the prevention of roof failure is a major concern of mine management. Many ground failures observed underground are associated with geological discontinuities such as fractures, faults, clay veins and sandstone channels inherent in the earth's crust (Rinkenberger, 1977). To properly design a mine requires an advance knowledge of such geologic discontinuities and this is not always available from exploration boreholes. The use of remote sensing for mine planning is a relatively new development, and is at present being used primarily by the Roof Control Support Branches of the Mane Safety and Health Administration (MSHA) in Denver and Pittsburgh. However, technical advances, coupled with public access to previously unavailable photographic products, make remote sensing a useful aid in the difficult process of mine planning (Jansky and McCabe, 1979). Remote sensing techniques are being used to predict the location of geological features in advance of mining which influence roof conditions. The features appear on photographic images as linears, which are plotted on a mine map and serve as a planning tool for mine management. Also, during development of entries toward a linear, mining personnel will be on alert for signs of unstable roof conditions which might normally go undetected. Preventive action can then be taken before a fall occurs. A confusing aspect in remote sensing, analyses is terminology such as linear, lineament, fracture trace and joint. In this report the term "linear" refers to a line-like appearance on an aerial photograph or satellite imagery which signifies a naturally occurring geologic feature no the earth's surface. The objective of this paper is to describe the use of remote sensing techniques as an aid in predicting geological discontinuities which might produce hazardous roof conditions to a mine operating in the Pocahontas No. 4 Seam in southern West Virginia. Mine projections and roof control plans will he developed based on this and other available information such as data from cored drill holes.

Jan 1, 1982

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By Chris Strawson

Moranbah North is a modern longwall operation mining premium coking coal in the Northern Bowen Basin, Central Queensland. Australia Moranbah North Coal (MNC) is owned and operated by Anglo Coal Australia. Extracting approximately 4.5m of the Goonyella Middle seam using a single longwall, the mine produces 5 to 6 Mt per annum. The weak coal (4.5 MPa), low strength laminated immediate roof, and strong upper roof sandstones, make operation of the longwall at depths in excess of 250m geotechnically challenging. In the past, there have been a number of production delays due to geotechnical issues. Roof instability resulted in a long stoppage on Longwall 105, and the eventual relocation of the face further outbye in the block. (Figure 1). When mining commenced in LW106, there was a requirement for uninterrupted production, particularly in the more demanding inbye area of the panel. Following discussions with a number of Geotechnical experts, it was decided to narrow the face, and test the theories of reduced face weighting due to spanning of the goaf across the panel. A new on line chock monitoring system, and microseismic monitoring was installed in order to characterise the difference in the rockmass response, as the panel width changed from 175m, to 265m, and then 300m. The nature of the goaf formation and impacts on face loading and production are discussed, having the unique opportunity of three different face widths within the same area.

Jan 1, 2007

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Takashi Sasaoka, Hiroshi Takamoto, Kikuo Matsui, Hideki Shimada

"Indonesia is the second largest coal exporter to Japan. Almost all the coal is produced from open cut mines. However, a great deal of coal is left in the highwalls of the mined-out pits. The use of highwall mining systems has increasingly come into play in the U.S. and Australia, when overburden depth exceeds economical recovery in an open cut mine. However, the stability of the highwalls is always a major safety concern in such mining. This paper describes the characteristics of the highwall mining system and discusses the appropriate highwall mining system for use in Indonesia.INTRODUCTIONIndonesia produces over 200 Mt of clean coal and is the second largest coal exporter to Japan, accounting for about 32 Mt of coal annually. Over 99% of the coal produced in Indonesia comes from surface mines. More open cut mines will be developed and more coal will be mined in order to fill the great demand both in Indonesia and the rest of the world.In open cut mines in Indonesia, there are many sites where mining operations have developed long highwalls that have been abandoned due to the current economics. Mining operations have been transferred to lower stripping ratio blocks of coal or overlying seams. In some cases, coal lies buried beneath spoil heaps or is covered with mud and water. It is estimated that there is a great deal of coal beneath abandoned and working highwalls. Considering these situations, it seems to be worth introducing highwall mining systems into Indonesian open cut mines.Final highwalls of open cut mines can form the starting point for other mining methods, such as highwall or underground mining. In its basic application, highwall mining is a technique utilized after an open cut portion of a reserve has been mined, sometimes prior to the introduction of underground mining (Seib, 1993). In this system, the coal seam is mined by remotely operated equipment, such as an auger machine or a modified continuous miner incorporated into a highwall mining system. The major problems with highwall mining systems are less coal recovery due to leaving coal as the pillars and the instability of openings and highwalls due to the pillar and roof failures."

Jan 1, 2010

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Christopher Mark

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as "The UCS" for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: ? Brereton Limestone above the Herrin 6 seam (Illinois) ? Turner Mine Shale above the No. 9 Seam (Kentucky) ? Sandstone above the Eagle Coal (West Virginia) ? Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechnical exploration programs.

Jan 1, 2004

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The response of the surrounding rock mass to the creation of mining excavations determines the ultimate load on a pillar support system. In conditions where the ground is relatively soft and weak, the full overburden weight can be transferred to the pillar system. However, in stiffer and stronger rocks, a greater portion of the overburden load is transferred to the unmined coal barriers or abutments, and the pillar stress is reduced. This paper makes use of numerical models to examine the interaction between typical pillar systems and the surrounding rock mass for weak and strong geological conditions at various spans and depths of cover. The concepts of structural failure and functional failure of pillars are used to assess pillar performance when pillars are deformed beyond their peak resistance. The results show that the span-to-depth ratio is an important factor in determining the pillar stress and the ultimate deformation of pillars. The ultimate pillar strain appears to be closely related to the functional success of pillar systems.INTRODUCTIONThe National Institute for Occupational Safety and Health (NIOSH) was requested by Congress to study the safety of retreat pillar mining following the Crandall Canyon Mine disaster that took place near Price, Utah in August, 2007. As a part of this study, an investigation was made to better understand how the rock mass responds to the creation of mining excavations and how the loads are distributed among the pillars and the surrounding abutments or barriers. The outcome of these investigations contributed to the development of a modified loading model for the ARMPS-2010 (Mark, 2010) method ofretreat mining pillar design.Structural and Functional Failure of PillarsPillar design is typically conducted by estimating the pillar strength and stress, and then sizing the pillars so that an adequate margin of safety exists between the expected strength and stress. The pillar strength can be defined as the maximum resistance of a pillar to axial compression (Brady and Brown, 1985). If a pillar is loaded beyond its peak strength, load shedding or yielding can occur, and the pillar is considered to have failed as a structure. Structural failure generally refers to a loss of loadcarrying capacity."

Jan 1, 2010

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Brian Clifford

A wide range of different cablebolt systems are available and in use in hard rock and coal mines around the world. The birdcaged cablebolt was initially used in UK coal mines in conjunction with rockbolts in the late 1980's. More recently other cablebolt configurations have been used. Innovations in cablebolt design in the UK have been driven by a demand to find a system as effective as the birdcaged cable, but which can be installed more rapidly and offer immediate support. A laboratory short encapsulation pull test (LSEPT) has been developed for both rockbolt and tendon systems which measures bond strength and stiffness in rock and assesses the full range of potential failure modes. This test is now used along with conventional 'gun barrel' and shear tests to provide full assessment of bolt and tendon performance. This test may be incorporated into a new performance based British Standard for rockbolts and long tendon systems. This paper describes the performance of some of these systems as being applied to UK and South African coal mines.

Jan 1, 2001

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982