Search Documents

By Heinz Distelmeier

Short Historical Review Tunnelling in Germany is as old as it is in other industrial countries. Until the middle of this century German contractors had no chance to work continuously in this business except if they were operating internationally. Since 1960, however, tunnelling has been a growing market domestically. The reasons for this growth have been both in the growing demand of traffic routes and also in an increasing environmental consciousness, which tries to transfer any cause of disturbance underground. Tunnelling engineers of course don't complain about this trend. As almost every German city is built upon water-bearing soft ground, shields have been used soon after they were first successfully utilized in Great Britain and the United States. Until the seventies lining systems for shield tunnels were predominantly either cast iron segments or concrete segments for primary support combined with different sealing systems and a secondary concrete lining cast-in-place. Steel ribs and timber lagging for primary support has not been utilized in Germany, since the owners don't accept timber to be left in the ground. In 1973, for the first time, permanent linings were constructed with watertight segment rings of precast concrete (Fig. 1). This lining was developed as an economical solution for use with slurry shields in noncohesive, water-bearing soils that required an immediately watertight lining. Extruded linings have a similar effect, although these still need a secondary lining

Jan 1, 1987

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By Ulf Svensson, Donald E. Zipperian

This paper reviews commercial installations of FLOTAIRE Column Flotation Machines for metallic, nonmetallic, and coal flotation. Second generation FLOTAIRE Column Flotation Machines employ dual aeration systems to provide a mixture of air bubble sizes. Operating data presented in this paper shows that optimum grade and recovery relationship for each rougher, cleaner, and scavenger application are obtained by adjusting the ratio and volume of aspirator air bubbles and micro diffuser air bubbles.

Jan 1, 1988

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By Michael D. Zuber

This paper discusses the use of a coalbed methane simulator that has been modified to account for the removal of grid blocks as a function of time to estimate gas emission and production for a variety of mine-associated problems. The specialized features of the simulator are presented. Example applications illustrate the models' use in estimating methane emission rates during mine roadway development, and estimation of longwall panel degasification by horizontal boreholes.

Jan 1, 1997

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

By A. Shtiza

This literature review discusses the role of the Albanian institutions, the natural resources industry, potential investors and stakeholders in order to provide a set of indicators that can help to monitor amelioration within sustainable development principles. A map with the potential prospects of the natural resources will be a first step in identifying the further potential for exploitation. Mineral resource policies and governance, sustainable processing and supply chain as well as environmental management information system are some of the crucial tools identified, that will help to set up the indicators and quantify the achievements in environmental management in Albania. Moreover, the integration of practices that will support institutional capacity building; follow-up practices; the mainstreaming of global environment into planning; and the compliance monitoring process will additionally improve the environmental situation in Albania. Aligning business strategy with environmental policy, socio-economic analysis, environmental auditing are decisive tools in order to provide the Albanian authorities with a clear overview of the economic costs and the social benefits for sustainable development.

Jan 1, 2011

By J. W. Leonard, D. A. Newman

By using physical and chemical means to increase the bulk density of newly broken coal freed from the mine face, the potential to improve coal mine productivity is significantly enhanced. It is estimated that by increasing bulk density, greater tonnages can be placed in fixed volume scoops and shuttles cars to improve production by as much as 10% to 20%. Such improved packaging to achieve new levels of volumetric efficiency might require only small and easy to implement changes to present downstream mining operations. Opportunities exist for improving broken coal bulk density from the moment of breakage, during transport across the continuous miner or loading machine, during discharge into the haulage unit, and after placement in the haulage unit. Physical/chemical methods for broken coal compaction in mobile, fixed volume units in underground operations are discussed.

Jan 1, 1990

By Ross W. Smith, Xiapeng Zheng, Merrill P. Allen

The results of flotation of a primary desliming hydrosizer overflow material containing 14.6 wt.% P20, and 3.6 wt.% MgO are presented. The phosphate minerals were collophane and francolite and all minerals appeared to be liberated. The material had not been previously treated with flotation reagents. In the experimentation, various collectors were evaluated for effectiveness. The relative effectiveness of flotation in different flotation devices was determined. Finally a two-stage flotation scheme is proposed using column flotation of dolomite in the first stage and Denver cell flotation in the second.

Jan 1, 2002

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By R. Hogg, T. F. Dumm, L. G. Austin

The applicability of SEM/EDS techniques to particle-by-particle analysis of respirable coal dust is evaluated. It is demonstrated that the correction procedures needed to account for the failure of most EDS systems to detect light elements (especially carbon) become unreliable for particles in the respirable size range (< 10 µm). Other serious limitations arise from x-ray counting errors for coal particles with low but significant mineral content and particle counting errors for liberated mineral matter.

Jan 1, 1991

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal&apos;, present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar&apos; while the new design employed a 36.6 by 54.9 m&apos; abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Ronald K. Frobel, Christopher J. Wienecke

Geomembrane systems and associated geosynthetics such as geotextiles, geonets, geogrids and geocomposites have been used in precious metal heap leach and tailings facilities for many years. Geomembranes have been used in the heap leach process in pad design and solution recovery ponds as well as associated collection channels as the primary liquid barrier to contain and collect metal bearing leach solution. Geomembrane systems offer an effective, low cost alternative to other containment methods such as compacted low permeability soils, asphalt or concrete. In the 19BO's, rigid High Density Polyethylene (HOPE) liners were used to a great extent with a gradual transition to the use of the more flexible Very Low Density Polyethylene (VLDPE) and Polyvinyl Chloride (PVC). These three geomembrane systems have been used successfully in precious metal heap leach solution containment. Predominant material thicknesses have been 30 and 40 mil for PVC, 40 and 60 mil for HOPE and VLDPE. Variants in recent years have included roughened HDPE and VLDPE to provide higher surface friction characteristics, as well as newer polymer materials such as polypropylene. In addition to providing an economical method for providing enhanced solution recovery, geomernbranes are also providing the primary liquid barrier for prevention of groundwater contamination. Because heap leach solution chemical components and dissolved metal constituents are classified as toxic substances, they are subject to environmental regulation. Many regulatory agencies are still developing guidelines for heap leach pad design, however a geomernbrane liner system is often used as a single liner or in conjunction with other materials to form composite double or even triple lined systems. "Other" materials can include alternate layers of drainage aggregate, geotextiles, clay layers and other geomembrane or geocomposite layers.

Jan 1, 1993

By Haia Roffman, Amiram Roffman

A gas company operated more than 100 distribution stations. Mercury filled manometers were used for years in these stations to measure the flow of natural gas through the system. Use and handling of these manometers resulted in mercury spills and ground contamination. To assess the human health and environmental effects of these spills and the need of remediation, it was important to determine mercury specific species present and their concentrations. Soil samples were analyzed for total mercury, methyl mercury, inorganic mercury and elemental mercury. These analyses served as important input in the risk assessment performed for these stations.

Jan 1, 1998

By Bruce Hebblewhite

"Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining. The motivation for such models varies, ranging from understanding the impact of mining on surface subsidence to back-analysis of caving behaviour in the immediate roof behind the longwall face. One of the most critical motivating factors that is taking on increased importance in many coalfields is the need for better understanding, and hence prediction of the impact of mining on overlying strata, particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the Southern Coalfields of New South Wales, south of Sydney. The paper discusses the parameter often referred to as “height of fracturing” in terms of the critical parameters that influence it, and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact. The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used. The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.INTRODUCTIONKnowledge of the detailed nature of rock deformation and failure above any form of large-scale underground mining is always going to be limited to interpretation from a very incomplete set of data. It is extremely difficult, if not impossible, to directly measure the detailed nature of the rock failure, fracture networks, and deformational behaviour above an extracted mining area. Limited techniques such as borehole extensometry can provide some evidence of relative or incremental deformation in the direction of the borehole (usually vertical). However, such data cannot assist below the horizon where full caving has caused major rotation and dislocation of rock blocks and effectively destroyed the instrumentation borehole. Above such a horizon, the data is only valid along the axis and in the direction of the borehole, and to the level of detail defined by the extensometer anchor spacing intervals. It is often also restricted by major shear planes intersecting the extensometer borehole and cutting off the instrumentation below the level of the shear horizons."

Jan 1, 2019

By C. A. Fleming, C. J. Ferron, I. Dymov

An oxidized gold/silver ore from Mexico has been evaluated at Lakefield Research in order to develop an economically viable treatment flowsheet for the recovery of gold and silver. Initial cyanidation test results indicated that at least 20 kg/t cyanide was required for maximum gold and silver extractions, due to high cyanide consumption by an oxidized zinc mineral present in the ore. A process was developed for the recovery and recirculation of the cyanide from the leach liquors. The proposed flowsheet included direct cyanidation, CCD and Merrill-Crowe, followed by precipitation of the zinc associated with cyanide with sodium sulphide and recycling of the regenerated cyanide liquor to the leach circuit. The process was demonstrated during a continuous pilot plant. A mill has been erected recently in Mexico and has been operating using this flowsheet.

Jan 1, 1997

By H. D. R. Browner, D. A. Marsh

The need for a product dewatering step between the milling/classification and leach/carbon stages of gold plants has traditionally been performed by thickeners. Whether these be the 'conventional' or 'high-rate' types both require considerable initial capital outlay even without provision for standby facilities. In addition, their sensitivity (both mechanically and metallurgically) to changing feed conditions often results in these being considered 'high-risk' items of equipment, requiring a high degree of attention from operating personnel.

Jan 1, 1992

By F. Ferella

In this paper several leaching tests were per-formed to optimize the leaching section of a hydrometallurgical process for the recycling of alkaline and zinc-carbon batteries. Zinc and manganese oxides were dissolved by an acidic-reductive leaching using sulphuric acid and oxalic acid as reductant. Leaching tests were developed according to a full factorial design. The operational variables were pulp percentage, sulphuric acid concentration, temperature and oxalic acid concentration. Additional tests were performed to evaluate the precipitation rate of Mn and Zn oxalates. Finally a hydrometallurgical process were proposed for the recycling of alkaline and zinc-carbon batteries, in which Zn and MnO2 are recovered from purified solution by electrowinning: Zn is recovered as metallic compound, while Mn can be recovered as electrolytic manganese dioxide (EMD), but recovery of further manganese compounds is possible with simple process changes.

Jan 1, 2006