Search Documents

By W. C. Morgan

The Federal Surface Mining Law enacted in 1978 is now being translated into regulations which must be followed in future coal mining. Substantial change to mining procedures is required to maintain stricter air and water control while mining and to return the mined out land to equal or better use than before. These changes do not come easy; and in most cases, they create a substantial additional cost. Based on field observations and mining studies, Caterpillar has been making suggestions on the use of their types of equipment to conform to the new standards at the least cost. This paper will be a brief review of some of the overburden stripping and reclamation methods suggested by Caterpillar. A production and cost comparison of dragline, scraper/dozer and truck, loader systems in 20 to 150 ft. Overburden conditions illustrates potential cost savings using mobile equipment.

Jan 1, 1980

By D. W. Frommer

In continuing its long range studies of methods of treating low-grade iron ores, the Bureau of Mines has developed a new selective flocculation, desliming, and flotation procedure that enables effective beneficiation of the finely disseminated ferruginous jaspers of the Marquette range, Mich. The process, developed on a bench scale and later confirmed in the 800-lb/hr pilot plant, comprises dispersion, selective flocculation, desliming to reject fine silica and clay, and flotation of silica from the remainder of minus 400-mesh pulps. Pilot plant flotation of two Marquette range ores, using the selective flocculation procedure on feeds containing 36 percent Fe, yielded iron recoveries of about 84 percent in concentrates containing 65 to 66 percent Fe and 4 to 5 percent silica. These results were metallurgically superior to those obtained when selective flocculation was not used. Also operating characteristics were better, and reagent costs were lower.

Jan 1, 1964

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By John F. Clarkson

White Pine Copper Company built and operated, from August, 1962 through May, 1963, a pilot plant to recover copper using a cyanide percolation leach of the sand fraction (+400 mesh) of the mill tailings (1, 2, 3). The pilot plant runs were metallurgically successful and preliminary engineering studies for a full scale operation were completed under contract by an outside engineering firm. Unfortunately, the net return projected at that time did not justify the proposed capital' investment. In the summer of 1973 the project was revived. The rise in selling price of copper over the previous ten years, compared to the projected operating cost of the leach plant, increased the calculated net return on investment with the most recent figures showing a 30% DCF. Basically, the reason for this favorable shift in profitability was that the cost for many of the reagents did not go up as fast in the previous ten years as did the selling price of copper. Using the Chemical Marketing Reporter costs, NaCN sold for 18.3¢/lb in 1963 and 20.75¢/lb in August, 1973. During this same period H2S04 went from $23.50 per ton to $35.90 per ton. In comparison, producer's prices for electrolytic copper were 31¢/lb in 1963 and 619 in 1973. Thus the price of copper went up 97% while the two reagents only increased 13% and 53%, respectively. The capital investment also escalated but, again, not to the same extent as the selling price of copper. These price differences no longer are valid' but they did provide justification for reexamining the project.

Jan 1, 1975

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By D. L. Kowal, P. J. Whittaker, M. A. Tuzun, N. O. Lotter

The area of flotation testing of drill-core is important in the business plan of most mining companies. Metallurgical information derived from this practice can be used to advantage in strategic decision-making. Sampling, flotation testing and subsequent Qem SCAN analysis of a mineral resource is one example of this approach. Anew resource, located in Sudbury, Ontario, is being assessed for the Sudbury Operations of Falconbridge Limited, which includes the Strathcona Mill. In this case, it was possible to improve the value of information from sampling and flotation testwork by using an improved, statistically-based test design, by sampling the resource by generic end-member ore type, and by integrating the Mineral Processing and Mineral Science disciplines into a Process Mineralogy team. In addition to producing standard metal grade and recovery information, this new approach provides more reproducible information from representative samples and flotation testing in a replicate format. Qem SCAN technology is used to produce a size by size mineral balance, including both modal percentages and liberation, from which flotation models for each ore type can be developed. As a result, a key understanding of the potential behaviour of a given ore type, if mined and then processed at the current mill operation, is gained at the 95%confidence level. The three ore types of this mineral resource were shown to have different flotation characteristics. Quantifying the mineralogy and liberation in each of the three ore types, has shown that this difference is due to changes in modal percentages of ferro-magnesium and magnesium silicate minerals such as pyroxene, talc and serpentine. Liberation across the three ore types is very similar and is therefore not responsible for variation in flotation performance.

Jan 1, 2003

By L. Reyes-Bozo, R. Ginocchio, A. Godoy-Faúndez, C. Sáez

Relationships among mining industry, society and environment have been historically complex due to its environmental impacts. In the Chilean mining industry, repetitive and small spills of fuel during maintenance of machinery have been adsorbed by desert soils and sawdust to control environmental pollution. The froth flotation is the main technology to recover specific mineralogical species from sulphide ores. Flotation reagents are expensive and representing an environmental risks due to its physics properties. Our objective was to investigate the feasibility of applying bioremediation as a cost-effective alternative technology to physical-chemical treatments and to evaluate the efficacy of biosolids as foaming agents. Our results show that the bioremediation is feasible by use of the autochthonous microbial communities and biosolids could be used as new environmental-friendly organic reagents. This research discloses a sustainable bioremediation process and industrial ecology model based on these two successful cases.

Jan 1, 2011

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company's Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

A combination field and office study of mining districts in Southwestern U.S.A., conducted in 1949 - 1950 by United Geophysical Company, embraced all of the essentials for a successful exploration project including factors such as geology water, transportation and many more. Perhaps the best known of several high priority areas chosen from the study was the Twin Buttes or Pima District in Arizona, however, the Turquoise District also ranked very high on this priority schedule. Following the discovery of the Pima Mine in 1951 and 1952, United initiated additional preliminary geological, geophysical, drilling and claim location work in the Turquoise District, but stopped shortly thereafter, when ASARCO began adjoining competetive activity. During the summer of 1957, sometime after ASARCO abandoned their claims in the area, Minerals Exploration Company began intensive exploration in the Courtland-Gleeson part of the District. This program was terminated in 1958. Later Bear Creek Mining Company supplemented the discovery endeavor with their own program during the period 1960 through 1962. This paper summarizes most of the geophysical work done by all of the groups except ASARCO and is intended to complement the recent paper "General Geology and Some Structural Features of the Courtland-Gleeson Area, Cochise County, Arizona" by Mr. Otis McRae of Bear Creek Mining Company.

Jan 1, 1966

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980

By B. Karatzoglou

The penetration of sustainability principles in business practices has introduced the necessity for a simultaneous integrated assessment of the corporate economic, environmental and social performances. Continuous technological, political and legal evolutions indicate that Sustainable Development (SD) principles will soon have to be implemented in all sectors of the Greek corporate reality, among them in the Mineral and Mining Industry. However, the ultimate criteria for the evaluation of a company?s performance remain its profitability and its market value. Managers, shareholders, financial intermediaries, all alike, emphasize and base their decisions on the various accounting produced ratios of return (ROA, ROE, ROCE, Residual Value) included, or produced by data found, in the financial statements of the companies. This paper offers evidence that the traditional accounting ratios discourage the implementation of investment plans that aim at improving the environmental performance of companies and therefore can be inadequate and misguiding for SD applications. International studies have consistently traced a positive relationship between the environmental performances of firms and their financial positions. Yet, the fact that investors tend to reward proactive companies by increasing their corporate values is disregarded by the return ratios, which usually set up the basis for management rewards and bonuses. The book value of the firm assets and owners? equity from which such ratios are produced diverges strongly from the real corporate value, defined as the traded amount for the stock of a firm. There is an urgent need for an adjustment of the return ratios so that they can record the positive economic impact of a more sustainable attitude and encourage decision makers towards this direction.

Jan 1, 2003

By C. J. Pritchard, A. B. Cecala

An evaluation was performed on a district recirculation system at a trona mine in Granger, WY. A 1.52 m-diam (5 ft-diam), 37.3-kW (50-hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated about 31.4 m3/s (66,578 cfm) of air back into the intake. This amounted to a recirculation factor of about 20% of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 610 m (2000 ft) and 1829,m (6000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF6 tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1992

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979