Search Documents

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user's questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By Richard J. Fantel

The U.S. Bureau of Mines performed engineering and economic analyses on 130 domestic phosphate mines and deposits, all containing demonstrated resources, of which 73 are in the Southeastern states of Florida and North Carolina, to determine the domestic availability of phosphate rock. Of the total domestic resources studied (6.4 billion tons of recoverable rock) over 60 percent is found in these two Southeastern states. At an estimated cost of $30 per ton, in January 1981 dollars, approximately 1 billion tons of rock is potentially recoverable from Southeastern deposits, increasing to 3 billion tons at $45. In addition, there is nearly 6 billion tons of recoverable rock at the inferred level (some presently unmineable) in Florida and Georgia.

Jan 1, 1983

By Y. J. Wang

The concept of subsystem characteristic curves for multiple-fan ventilation networks is presented through the construction of characteristic curves for two-fan, series-parallel networks. By considering fans as the individual network branches, the multiple-fan network is viewed as consisting of two components: any one fan branch, which is called the reference fan branch, and its associated subsystem. Thus, F subsystems can be designated for the network with F fan branches. Each subsystem contains one or more fan branches. The subsystem characteristic curve is the pressure-vs.-quantity curve of the subsystem. As illustrated in the example networks, the subsystem characteristic curve is not a strictly increasing curve and does not pass through the origin. The intersection of the characteristic curves for the subsystem and the reference fan branch represents an operating point. Multiple intersections therefore represent multiple operating points.

Jan 1, 1994

By D. L. Johnson

A number of small but rich copper sulfide (chalcocite) ore deposits are located on Michigan's Keweenaw Peninsula. These deposits are considered too small to warrant the capital investment required for conventional mining. However, they are being considered for in-situ solution mining as a way to revitalize the area's once prosperous copper extraction industry. Geology, mineralogy and geohydrology of the deposits have been investigated to determine their suitability for leaching; Three conclusions were drawn from the work. First, the sulfide mineralization is found primarily in fractures (65%) and, therefore, is accessible to injected leach solutions. Second, the ores are shallow, occurring from surface exposure to about 200 meters depth; injection and recovery wells would not have to be excessively deep. Third, the rock was found to have low permeability, in the neighborhood of thirty millidarcys or less. However, preliminary hydraulic fracturing experiments indicate that this will be an effective method for permeability enhancement. In one experiment a permeability increase of 100 times was achieved using a very low injection pressure at shallow depth. Additionally, fracture aperture spacings measured from drill core were correlated with fair success to field permeabilities.

Jan 1, 1989

By Michael Chender

Introduction Clearly, many problems confront the minerals industry today. Yet, at the same time, there is too much energy spent bemoaning the negative effects of difficult economic circumstances, low metals prices, and adverse government policies. These are factors that cannot be altered by individual mineral company reactions. In fact, as we look to the future, the only thing we can be certain of is that we will continue to be faced with uncertainty. Thus, an area that demands close scrutiny and that can significantly affect a company's performance in the future is the posture it adopts to deal with uncertainty. This paper looks at how strategies are developing to deal with this issue. It also examines some of the implications that implementing such strategies have for the role of the individual explorationist. Elements of strategy Whether mineral company strategies are based on diversifying or retrenching, on emphasizing primary production or downstream integration, there seems to be increasing agreement that in the current environment strategies must have several features. They need to be information-based - developed out of access to timely and complete data and analysis about proposed directions and competitor activity, rather than simply following a current fashion. They need to be flexible - adaptable in light of changes in the marketplace and an unpredictable industry. And they need to be cost-efficient - making the most of limited resources. Whether a company is looking for gold financing opportunities, acquiring polymetallic prospects, or doing grassroots exploration for diamonds, these three elements are increasingly essential. They not only allow the company to pursue its current goals most expeditiously, but also open it to hearing and using feedback in the most constructive way. The company can then improve or change strategy as it proceeds. And it can be best positioned to take advantage of opportunities as they arise. These elements of strategy place great emphasis on the skills of the individual. The need for critical intelligence and the reduced amount of capital available to manage are making it more obvious that exploration is a "people" business. This is in accordance with a general trend in many sectors of industrialized economies, reflecting the widely discussed shift from smokestack to information-based industries. Increasing the odds There is a direct connection between successfully implementing the approaches to strategy discussed above and encouraging and improving the quality of work of the individual explorationist. To illustrate the importance of this, some commonly quoted figures on the odds of discovery success can be used. These figures are arbitrary but illustrative. Assume that one out of 100 exploration prospects actually turns out to be a promising ore body, and that one out of 1000 becomes a mine. Based on our research, chances are the most of those

Jan 1, 1986

By Martha Caudill

When planning for the required amount of storage capacity at a proposed open-pit coal mine or determining when additional storage capacity should be added to an existing operation, the decision must be based on a breakeven- analysis relating the discounted cost of capital for storage capacity to the marginal costs incurred for additional crew call-outs on weekends and demurrage charges. The model developed in this paper uses simulation techniques applied to two coal mines in the Powder-River Basin to determine how much storage capacity is needed and when it is needed. The paper also generalizes the simulation model so that it can be applied to any type of open-pit mining operation. Two important results of the model are (1) all of the mines in the Powder River Basin have excessive amounts of storage capacity, and (2) management is provided with estimates of the total number of hours that crews will have to work on the weekends as annual tonnage increases, and the levels of demurrage costs incurred.

Jan 1, 1986

By K. Cothern, S. Novack, D. A. Johnson, R. Borden, S. Pavlou

A procedure is presented for ranking hazardous waste sites for remedial decisions, and an example with application to mining waste sites is discussed. Typical contaminant concentrations are calculated from field data. Exposure indices that compare these measured concentrations with allowable limits are then computed. The limits are selected to protect both the health of humans (for both carcinogen and noncarcinogen effects) and the health of key organisms in the ecological food web. The additive exposure index for a site, defined as the sum of all contaminant-specific exposure indices, is then used in ranking the sites and assigning each a priority for remedial action. One key source of uncertainty in the process is the estimation of a typical site concentration from data that include values reported as "below certified reporting limit" (BCRL). This uncertainty is compounded in the additive exposure index and therefore may have a substantial effect on the assignment of remediation priority. A general approach is presented for incorporating consideration of BCRL data into uncertainty evaluation when assigning remediation priority designators to hazardous waste sites.

Jan 1, 1992

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By R. Todd Swinderman

Variations in designs between belt cleaner systems are so wide that it is impractical to establish a dimensional stan- dard. The number of variables that affect the efficiency of belt cleaners is too great to assume a required number or style of cleaners for broad classifications of bulk solids or typical applications. The amount of carryback remaining on the belt is more dependent upon the characteristics of the bulk solid and the physical parameters of the conveyor system than it is on tonnage of material conveyed. Therefore, a performance-based standard is proposed. Three levels of cleaning performance are proposed: • Level I cleaning is general specified when concerns about carryback are not critical. Cleaning systems normally associated with achieving a Level I performance are single or double cleaner systems with one-piece blades undergoing poor to average maintenance. Frequent cleaning of the carryback that falls from the return run will likely be required. • Level II cleaning is generally specified when carry- back is of concern but does not create a safety or environmental problem. Cleaning systems normally associated with Level I1 performance are multiple cleaner systems with segmented blades undergoing the manufacturer's specified maintenance. Regular but infrequent cleaning of the carryback that falls from the return run will likely be required. • Level III cleaning is generally specified when con- cerns about carryback are critical. Concerns range from safety to environmental to product contamination. Cleaning systems normally associated with achieving a Level 111 performance are multiple cleaner systems in conjunction with at least one low- volume water spray. Scheduled inspection and the manufacturer's specified maintenance would have to be performed to maintain a high level of cleaning performance. Difficult-to-clean bulk materials may require the use of a washbox system with multiple cleaners using a combination of low-volume eater sprays to lubricate the cleaners and high-volume sprays to keep the washbox and discharge piping freely flowing. Further addition of a water and sludge recycling system reduces the amount of water that ends up in the product to a negligible amount. Very infrequent cleaning of the carryback that falls from the return run will be required. PURPOSE The purpose of this proposal is to propose a standard method for specifying belt cleaner systems based on user expectations and equipment performance over time. DEFINITION In bulk solids handling by conveyor belt, carryback is the material that adheres to the belt after the belt discharges its cargo. PROPOSED STANDARD Required Basic Good Practices There are a number of basic design and operating principles that are good practice for the selection, installation, and maintenance of belt cleaning systems on conveyors in order to achieve "standard belt cleaning performance over time. 1. The Belt Cleaning System shall be designed to meet the performance requirements based on the worst operating conditions and worst bulk solids proper- ties that are expected. 2. Each conveyor discharge point shall be designed to readily accept the manufacturer's recommended minimum number of belt cleaners. In addition, the discharge chute shall be designed to accept, with minor modifications, at least one additional cleaner if it is required.

Jan 1, 2004

By J. Y. Perez, H. M. Ewoldsen, L. L. Oriard

Near the village of Villarino de los Aires, in the province of Salamanca, Spain, is an existing underground hydroelectric power plant. A major enlargement was undertaken to increase the electrical generating capacity, under a contract awarded to a joint venture of Dragados & Construcciones, S.A., Entrecanales y Tavora, S.A., and S.A. Conrad Zschokke. The enlargement required the excavation of an underground system of tunnels, shafts and chambers adjacent to existing facilities and interconnected with these facilities. The existing machine hall and transformer chamber were both extended, requiring excavation of the rock that constituted the existing end walls of these chambers. The drilling, blasting and excavating of the underground system had to be done without damaging existing underground openings or any of the existing structures, equipment or instrumentation facilities. This required careful control of vibrations, air waves and dust. The joint-venture contractors preferred to use electric blasting methods, if these methods could be implemented in a safe manner. The safety question had to be evaluated carefully. High electrical potentials existed at the site because of the electrical generating and transmitting facilities that could not be shut down. Electrical fields were carefully studied prior to the beginning of the work. This was done both in the underground environment and above the ground surface. Special procedures were followed to ensure safety with

Jan 1, 1974

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By M. Z. Rashad, H. A. El-Sageer

This paper compares the covariance and multiquadric functions in some mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 km2 x 16 km2 area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of 48 test stations were computed by using the data of 63 control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function is simpler in computation than the covariance, which requires precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometric and physical considerations rather than covariance functions.

Jan 1, 1992

By Clyde N. Garman

The Homestake-New Mexico Partners consist of Homestake Mining Company of Lead, South Dakota; Rio de Ore Uranium Mines, Inc; United Western Minerals Company; White, Weld and Company; J.H. Whitney; San Jacinto Petroleum Corporation; and Clyde Osborn, Homestake Mining Company is the general partner, the others are limited partners. The Rio de Ore Uranium Mines, Inc. has. a mine in the Ambrosia Lake area; this was the first mine to go into production in this area. The United Western Minerals Company also has a mine in the Ambrosia Lake which is operated as a "farm out" from the San Jacinto Petroleum Corporation. These mines are the principal sources of ore for the mill. This group was the first to obtain a contract with AEC to make uranium concentrate from Ambrosia Lake ores and the first to have a mill in operation specifically for these ores. With Clyde Osborn as the sparkplug and co-ordinator holding the ore suppliers of, this group together, a contract with AEC was agreed on as to its essential points by mid-summer, 1956, At that time, there was no general partner and no financing, so me formal contract could be signed. By December, 1956 when the contract was signed and the present partnership officially formed, much of the basic engineering was done and purchasing of main elements of the mill waited on the formalizing of agreements, at the specifications and sizes agreed on previously. Ground for the mill was broken in April, 1957. The sampling plant went into operation in October and ore was first fed to the ball mills on February 5, 1958, ten months after construction actually started. Filling of the circuit with sodium carbonate bicarbonate solution had begun a week before that.

Jan 1, 1959

By Thomas Fliess, Klaus-Christof Ritter, John R. Sturgul

The optimum flow of materials through a smelter is an extremely important phase of the mining cycle. A typical copper smelter will have up to $US 1,000,000 per day of copper being processed. The motion of the overhead cranes in moving the ladles filled with copper matte and slag from furnace to furnace is prescribed but there can be numerous variables to consider. Some of these variables to the system can be: the speed of the overhead cranes, the number of cranes, the size of the ladles, the size of the furnaces, the number of furnaces and the sequence in loading the furnaces. A simulation model was constructed of a working smelter in the SW of the United States. The model has been used to study the effect of varying parameters of the system. The program runs as follows: an input menu appears on the PC screen and the user can navigate through it and change any of the data; the simulation takes place and the results of the simulation sent to a data file. Animation of the system then is shown on the screen in "cartoon" fashion. The software chosen for the simulation was GPSSI H (') and PROOF Professional (') for the animation. The model presented here is believed to be the first reported simulation and animation model for a complete, working smelter.

Jan 1, 1996

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials, and consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium (V). Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, Xray fluorescence (XRF) analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 weight percent V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples, calcium carbonates also significantly contribute to the V deportment, while wuestite, lime and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the Vbearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Aug 1, 2024

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By S. D. Thompson, L. Adler

Several researchers in the last 20 years have developed computer simulation models for designing coal mine belt systems. A careful review of these reveals that each omitted or oversimplified important factors, especially in belt loading. To remedy this, the coal mine belt capacity simulator (CMBCS) was developed to include various types of probability distributions, delays, and longwall and continuous haulage. CMBCS is computer coded in FORTRAN and employs the Monte Carlo simulation technique. Basically, the model simulates the loading and corresponding flow of coal through a belt system. By recording spillage and belt stoppage statistics for the simulated flow, belt and surge bin capacities can be evaluated. A complete user's guide is available. The modeling and verification of CMBCS are briefly described, and its major advantages and disadvantages are explored.

Jan 1, 1987