Search Documents

By R. Bhima Rao

Performing a magnetizing roast in a furnace or kiln is a well-established technology. However, the use of microwave heat for the magnetization of hematite in the beneficiation of ferruginous bauxite is a new approach. This paper reports on an investigation of this procedure, which is followed by comminution and magnetic separation. The results of this investigation indicate that a nonmagnetic product containing 80% A1203 and 2.5% Fe203 with a recovery of 80% can be made from a crude bauxite ore containing 55.9% A1203 and 5.6% Fe203. This product is suitable for refractory use. The mechanism is explained by the ability of the microwave radiation to heat specific points within the bauxite. These heat-specific points are at the location of iron minerals. In a reduced atmosphere, the microwaves promote faster conversion of the iron minerals to a magnetic phase, which improves the magnetic-separation process.

Jan 1, 1997

By M. F. Vancas

The San Manuel oxide ore reserve ranges in depth from being exposed on the surface to lying 1000 ft. beneath a conglomerate layer all of which is confined in the subsidence zone of an active sulfide block caving operation. Present day recovery of the oxide copper values is either by open pit mining-dump leaching, or in-situ leaching of the oxide ore using dilute sulfuric acid solutions and solvent extraction/electrowinning processing of the pregnant leach solutions. Future plans are for continuation of leaching with expansion of reserves and increased processing rates. The state of the mining industry and copper in particular has not been good for a number of years. All of the producers that are still operating have made major adjustments in order to remain competitive. Magma Copper Co. is no exception.

Jan 1, 1987

By T. Weimer

Gasification of carbonaceous energy carriers with simultaneousCO2 removal is a new and interesting alternative e.g. ZECA [1],HyPr-Ring [2], AER [3]. In the ZECA process lime supported Hydrogen generation from Methane is a basic process unit and the Hypr-RING process investigates Hydrogen generation from hard coal with addition of lime. Here the main objective is a further development of the AER process. High energetic efficiencies for gasification in the range of 90 % can be achieved if the humidity of the energy carrier is already sufficient for steam reforming reaction. The aim of the overall process is upgrading coals and biomass yielding into three valuable products: • A fuel gas ready for power generation • A CO2gas stream containing >95%, ready for transportation to disposal or chemical fixation • A pre-calcined feed for cement clinkering consisting ofCaO and coal ash Thus power generation and gasification are independent. A promising industrial application is the combination of gasification and cement production. Then only one additional reactor is required and the precalcination mass flows have to be increased.

Jan 1, 2004

By William Lodding

Unlike most ore minerals, the raw materials for lightweight-aggregate, such as clays and shales are abundant everywhere. In view of this ample choice, what are the reasons for many plant failures attributed to the raw material? How can we arrive at a proper choice of the raw material, the proper processing method for the chosen material, predict its behaviour in a plant and the properties of the final product? Determine the uniformity of the raw material and possible harmful impurities? One basic choice is sintered versus kiln-fired aggregate. It will be based on market preferences and availability of the raw material. Almost in every case a good raw material for one process is poison for the other.

Jan 1, 1964

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By J. M. Pugliese

The U.S. Bureau of Mines is developing designs and estimating costs for vertical in situ copper mining wells as part of its in situ mining research program. Conceptual designs and estimated costs for "deep" 1100 m (3600 ft) recovery and injection wells in an undisturbed copper ore zone are presented. Within a single in situ copper mining well, multiple perforated well completions and associated costs are discussed for two ore zones between depths of 370 m (1200 ft) and 550 m (1800 ft). The order of well specifications for designing these wells is explained.

Jan 1, 1995

By Dale A. Shay, Roy R. Cellan

The Santa Fe Mine, located in west central Nevada, began leaching ore in 1988 and completed ore processing in 1995. Homestake Mining Company has completed final reclamation of the site, including remediation of bare surface soils resulting from the oxidation of sulfide minerals and migration of acidity in the mine waste repositories. The need to remediate oxidized sulfides and mitigate resultant acidity at the Santa Fe Mine emphasizes the economic, reclamation, and environmental advantages for understanding and pre-planning for management of potential sulfide wastes during mine planning phases. The lack of pre-planning by mining companies for sulfide waste management was common in the 1980's due primarily to mining of reserves characterized largely as oxide deposits and to the common opinion that low moisture regimes in arid or semi- arid climates would not allow for significant acid generation. Since the 1980's, operational experience has shown that sulfide wastes, deposited randomly in waste dumps and without adequate planning for final reclamation success, can create final reclamation problems that are very costly to remediate. While mine waste characterization, waste management plan compilation, and in-pit selective waste handling procedures add operational costs, the reclamation experiences at the Santa Fe Mine are indicative that pre-planning and management is worthwhile both in actual overall cost efficiency and in successful reclamation of the mine site. The reclamation program at the Santa Fe Mine shows Homestake's continued commitment to the successful management and reclamation of their mine sites.

Jan 1, 2000

By R. Freer

Recent developments in expanded PTFE membrane filter cloths offer high flow rates and sub-micron particle removal. These high strength, industrial grade filter cloths can be tailored for tubular filters, leaf filters and rotary vacuum drums. Filtration techniques using tubular filters make possible filtration of difficult slurries with the elimination/reduction of filter aids and chemical additives. This paper describes principles of surface filtration, applying the membrane filter cloth and comparisons to gravity separators. Benefits to the mining industry include clear effluent, enhanced solids recovery and accelerated cost payback.

Jan 1, 1996

By Xinming Lu

In this paper, we use a new kind of fan charateristic curve instead of the common quadratic function, and give the existence and the uniqueness of the solutions to the ventilation network controlling equations, so that the existence and the uniqueness of the solutions for the natural air distributting problem can be conveniently given. We also give a conjugate gradient method with the global convergence to solve the equations having the unique solution. Because we adopt a very efficient technique of one dimensional search (or linear search) in this method, the method can quickly solve a lot of problems, especially in large scale problems. The second part of this paper is the establishment of the model of the constrained quadratic programming for the measurement adjustment of mine ventilation network. We give the algorithm to solve this model as well. The two algorithms given above have been realized in the mic-computer MC-68000 with Fortran codes, and the numerical results are satisfactory.

Jan 1, 1991

By W. C. Yates

Lack of visibility from cabs of the large haulage trucks used in open-pit mines has become a serious safety problem. This Anaconda research program was conducted to develop a low-cost system for alerting haulage truck operators of the presence of small vehicles in their blind areas. Several systems, developed and tested to help solve this problem, are summarized and evaluated in this paper. As the size of the haulage trucks used in large open-pit mines has increased, so have the blind areas. Mine utility vehicles, pickup tucks and cars become concealed within these blind areas and, thus, become a serious safety hazard. Figure 1 shows the typical blind areas of a 150-ton haulage truck. The areas of greatest concern are those at the rear center and front right corner of the truck. It is within these areas of "no visibility" that numerous small vehicles over the years have been crushed by the large haulage trucks at various mine sites. Although the occupants in most instances, have escaped the vehicle before it was destroyed, injuries and deaths have occurred. The accidents, in most cases, were attributed to negligence or carelessness on the part of the driver of the smaller vehicle, but the problem of limited visibility still exists, and a solution is needed.

Jan 1, 1982

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, the pH decreased and metals increased. Output pH increased from 4 to more than 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long-term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2002

By H. Nazeri, T. G. Rozgonyi

Many industries when volumes of the solid materials are large invariably relay upon the gravity to induce solids to flow out of storage, through channels and reactors. In mining industry ore pass’s requirements to less energy (only gravity) have made them very popular both in underground and open pit mines. This paper discusses the major findings of research on 2D Discrete Element Method simulation of gravity flow of ore in ore passes. Results show that ore characteristics, ore pass configuration can significantly affect loads (static, dynamic) on the gate assembly and creation of hang-ups.

Jan 1, 2003

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By V. M. Torres

Arapiraca ore deposit has a mixed chalcopyritelbornite mineralogy, with a copper head grade of 0.7%. The reserve size does no allow profitable exploration by grinding/flotation. The technical feasibility of exploring the reserve by heap leaching was studied. Preliminary agitation tests indicated 85% copper recovery. To simulate heap leaching, column tests were performed. The tests included different ore types and acid addition levels. Operating at pH range 1.6-1.8, 67% copper extraction was achieved. Also, it was found an empirical correlation between the operation pH range, copper extraction and acid consumption.

Jan 1, 1996

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By P. Somasundaran, T. Chen, Diptabhas Sarkar

We have developed a layer-by-layer deposition technique for preparation of nanocomposite particles. Using this process, it was possible to make nanocomposites of various oxides with desired local composition and microstructure. The attachment of the shell particles to core particles was achieved using controlled polymer adsorption. Removal of excess polymer was accomplished without detaching the pre-adsorbed polymers by a specific stepwise washing scheme. The inherent chemistry of the process makes it easy to incorporate functional fillers over core particles. The nanosized filler materials will replace the shell particles in the present process and the polymer bridge would be chosen by taking into consideration the respective surface chemistries of various shell and core particles.

Jan 1, 2003

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974