Search Documents

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By C. L. Pillar

In the capitalistic system the success of a mining enterprise is measured by the rate of return on the investment and the speed by which its redemption is achieved. Exploration in search of ore deposits often results in the emergence of the lean orebody which does not meet basic company requisites. At this point a decision must be made whether to place the orebody into production or postpone production pending more favourable market conditions. The wisdom of this decision, borne out by future results, demonstrates the quality of a company's management and is instrumental in the degree of financial success it achieves. The project feasibility report must show a rate of return on the capital invested that is attractive to the company, plus its full redemption in the desired period of time, in order to bring the property into production on a sound economic basis. Mining companies have demonstrated their ability to bring the profitability of a marginal property from a point that says "no go" to a point of "go" by substantial reduction of expenditure without adversely affecting production rate or cost. Here is where the real challenge exists for today's mining engineers and plant designers; they will have to develop better ideas and concepts: ideas that will still allow maximum production at reduced capital expenditure, This is the sound way marginal orebodies can be brought into production without inflationary increases in the price of their product.

Jan 1, 1969

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By Yuting Xue, Taghi Sherizadeh, Mark Van Dyke, Dogukan Guner, Khaled Mohamed

The Coal Pillar Rib Rating (CPRR) technique has been developed to assist in rib support design in underground coal mines. One major challenge of the data collection process is the measurement of coal strengths in the field. Schmidt hammer has been verified as a useful tool to determine coal strength. An alternative approach is to obtain the representative strength of coal mass by determining the coal lithotypes in the field based on the coal brightness profile by experienced geologists or mining engineers. In this paper, image processing techniques have been used to quantify the texture of coal images of different lithotypes with the purpose of classifying coal lithotypes. The coal images were collected from the pillar ribs with exposed surfaces in underground coal mines, and the coal lithotypes were identified when taking the images. The method of Gray-Level Co-Occurrence Matrix (GLCM) was used to analyze the textures of coal images of different lithotypes, and the texture parameters, such as contrast, homogeneity, energy, and entropy, were compared. The results show that the images of coal with different lithotypes have different textures, which can be quantified through the image processing. The results from this study demonstrate the potential of classifying coal lithotypes using rib photos and easing the data collection process of CPRR.

Feb 1, 2024

By J. Tuck

This paper reports on an ongoing exploratory research program which aims to develop an understanding of the relationships between mining companies and their stakeholders and the importance of corporate citizenship policies to reputation and hence to corporate sustainability. The findings of the first stages of this research, the results of a focus group and an expert opinion survey into the drivers of reputation for mining companies are reported. This study was undertaken to provide an understanding of the drivers of reputation for a number of stakeholder groups and the perceptions held by mining companies of these drivers for their stakeholder groups. Results indicate that drivers vary between stakeholder groups - that in the case of drivers common to a number of stakeholder groups they may vary in their importance across the groups, and that there may exist a divergence between industry?s perception and stake-holders? priorities. These results further the understanding of the relationship between corporate citizenship and reputation in the mining industry, thus assisting companies to strategically manage their corporate citizenship investments and assisting them in their transition to sustainable development.

Jan 1, 2007

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By L. Adler

A fairly complex analysis is required to select, or evaluate a piece of excavating and bulk handling equipment and obtain its performance. At present there is little agreement as to what specific points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment from the bulldozer and the continuous miner, to the B.W.E. The importance of the equipment characteristics, job activities, and work conditions are stressed and separate analytical stems are established in a flow chart for these. They are combined using suitability tests in the following steps: 1) problem statement, 2) natural conditions, 3) suitability guidelines, 4) appropriate equipment types, 5) operational activities, 6) encumbered space, 7) geometric design, 8) equipment sizing, 9) failure and limits, 10) performance and consumption, 11) public policy checks, and 12) costs and profitability. Public policy and economics while considered throughout receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1983

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 1, 1988

It doesn't take any special acumen to note that US engineering and construction firms are busier than ever with mining projects in this mineral conscious world. This special issue of Mining Engineering takes a look at E&C companies-their expanding role, their special capabilities, and their challenges and problems. ME sent a questionnaire to a representative sample of E&C firms. Information was sought about officers, ownership, and amount of business. ME also asked about types of projects and commodities dealt in as well as market distribution and forms of payment. The accomnanying charts show how the 17 responding E&C firms answered these and other questions. Other ME survey questions, and a review of company literature, yielded information about financing techniques and special challenges for E&C firms. Insights were gained concerning government impacts, customer-generated problems, and promising areas for development-including synfuels-in the minerals industry. These areas are discussed later in this article. Accompanying articles in the special issue discuss the E&C company's role in mining projects, research and development in E&C firms, one approach to contract work used by an E&C firm, and an E&C project case study.

Jan 10, 1980

By John H. Paugh

Hydraulic slurrying and pumpability characteristics of phosphate matrix (ore) have not been quantitatively defined. An elemental triangular diagram analysis of rock/sediment texture is used to classify the nature of the ore; then related to empirical field data of hydraulic pressureand production yardage ratios. This experiment is applied as a geotechnical tool to provide empirical data of ore slurry and pumpability characteristics as key considerations in the design of slurry pipeline systems. A real texture variability maps are developed on a section of land to assist mine engineering planning.

Jan 1, 1981

By H. Colijn

The ever increasing price of bulk commodities forces buyers and sellers in world markets to take a more careful look at methods for obtain¬ing accurate accounting of commodity trans¬actions in commerce and material utilization in processes. Depending upon the application of a sampling and weighing system or the use intended, inaccuracies can result in an eco¬nomic loss of income or a loss in quality of the process. It inevitably results in a loss of control of ones costs. The accuracy of samp¬ling and weighing systems is today extremely important, as they are recognized to be the key components of the overall management system designed to provide both quantitative and qualitative control. This paper will be confined to the weighing systems only and will deal with various as¬pects of system design, calibration and opera¬tions. Special emphasis will be placed on new developments and requirements in this field.

Jan 1, 1988

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By M. P. Valoski

In the United States, the occurrence of underground mine fires/explosions continue to decrease; however, they pose great danger to the miners and any subsequent mine rescue teams and/or fire brigades. Tragically, 19 coal miners lost their lives in 2006 at fires or explosions. Fires/explosions can devastate a mine and cause its permanent closure. It is vitally important to obtain accurate information on the gas content (concentration and composition) of the mine atmosphere after the event so that appropriate action can be instituted to rescue any trapped miners while not exposing the mine rescue teams to unnecessary hazards. Additionally, the fire fighting techniques (spraying water, sealing, etc.) will be dictated by the gas content. Finally, the gas content will determine when it is safe to recover the mine. The gas content of the air can be determined using detector tubes, handheld instruments, portable instruments, or gas chromatographs. No single instrument is suitable for all analyses. Each type of instrument has its advantages and disadvantages. This paper discusses these attributes.

Jan 1, 2010

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By J. Wiebmer

The two most important influencers of cost-per-ton in an underground mining machine are its productivity (tons/hour) and its availability-utilization (hours/year). Operating cost and initial price have far less impact. This paper reviews a cost-per-ton sensitivity analysis for underground mining equipment and discusses benchmarks for measuring its performance. The conclusion is that miner-supplier partnerships and the Information Age are the two most significant trends in cost-per-ton reduction.

Jan 1, 1997

By Khosrow Badiozamani

Depletion of easily accessible coal reserves and stringent competition in coal marketing has led to the coal industries' need to more accurately assess alternate development scenarios and to develop well-conceived produc¬tion plans. This, in turn, has encouraged the active use of the computer during resource eval¬uation and mine planning. Morrison-Knudsen, (M-K) has developed proprietary software, known as "EAGLES", to support not only its own mine planning and development activities but also the mining industry in general. The EAGLES system provides complete geologic modeling, mine planning, production modeling, equipment modeling, and cost and financial modeling capabilities. In addition, EAGLES can be used for geotechnical studies, environmental assessments, and surface and groundwater hydrological evaluations. Another important tool used in today's mine development is Landsat (remote sensing). Landsat is especially useful in the evaluation of mining activities at remote mine locations and for megascale assessments of geologic structures and hydrologic regions. The use of scientific systems in the development of surface mines is being well integrated into today's mining operations and will be a major factor in the planning, development, and operation of mines in the future.

Jan 1, 1985

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

Equity investments and loans are made in oil and gas and mining projects by the World Bank Group (WBG) as one piece of a multi-faceted quest to reduce poverty. The Bank mandate to reduce poverty through private sector investments has been contested by civil society organizations, so the Bank has established an independent review, entitled the Extractive Industries Review (EIR) www.eireview.org. The EIR is reviewing, from the perspective of affected stakeholders, the impacts and benefits of WBG development policy. In this paper, we review the indicators used by the WBG, academics and others to measure the effectiveness of investments. We argue that currently used frameworks and indicators do not capture local or regional data sets, and instead focus on available and easily aggregated information at the national level. A case review of the WBG?s International Finance Corporation (IFC) and Multilateral Insurance Guarantee Agency (MIGA) investments and loans in Sub-Saharan Africa provide material data buttressing the argument. Poverty studies in the extractive industries have a long way to go toward measuring and accounting for dollars spent and invested. The paper concludes with a call for project level and regional indicators to track poverty alleviation. Data gathered for this research was funded in part by the Extractive Industries Review.

Jan 1, 2003