Search Documents

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By Jasinder S. Jaspal

The United States has very large coal reserves in seams that are less than 1065 mm (42 in.) thick. These reserves are often not mined because of the difficulty of working in low heights and, in most cases, the seams are beyond the technical or economical limits. It is estimated that the remaining reserves in 355 to 710 mm (14 to 28 in.) thick seams that are not faulted or intruded, dip less than 15° and under a cover of 610 m (2000 ft) or less are nearly 910 Gt (1 trillion st). This is a very large percentage of coal reserves in the United States (Unrug, 1985; DuCarme et al., 1990). The US Bureau of Mines is attempting to develop new techniques for mining 150 to 1065 mm (6 to 42 in.) thick coal seams. Research has focused on existing thin seam mining techniques, testing of small- and full-scale physical models of the Bureau's slot mining concept and computer modeling of the full-scale process. In 1986, only 21 % of the total US coal production came from -1065 mm (-42 in.) thick seams. Of that, 355 to 710 mm (14 to 28 in.) thick seams share of production was minimal, probably 5% or less (Mayercheck et al., 1990). This shows that the thin seams, particularly the seams 355 to 710 mm (14 to 28 in.) thick, have not been mined to the extent of the available reserves. Thin seam coal, generally, is of premium quality. As thicker seams are depleted, the mining of thin seams could become more important. Thus, there is a need to develop technology to mine these seams (J. Farinelli et al., 1987). A successfully applied technology could change reserve categorization. In the Appalachian Plateau there are 417 Gt (460 billion st) in 355 to 1065 mm (14 to 42 in.) seams. This represents nearly 9.2% of the US remaining reserves (Unrug, 1985). At depths of 152 m (500 ft) or less, the Appalachian Plateau has about 214 Gt (236 billion st) of reserves in 355 to 1065 mm (14 to 42 in.) thick seams. Other mining areas also have substantial coal reserves in this seam thickness category. Those, however, are not as attractive for mining as the Appalachian Plateau. In the past, most of the reserves of the Appalachian Plateau region were partially worked by contour and highwall auger mining. It is estimated that these mining systems had left some 40,230 km (25,000 miles) (Readers Digest, 1987) of unreclaimed highwalls. The Bureau recognized this situation. In FY1987, the agency initiated a research project to develop anew technology for mining thin seams of the Appalachian Plateau.

Jan 1, 1992

By Ulf Marklund, Manfred Lindvall

Fighting the challenge of diminishing ore grades, low base metal prices and a changing pattern of ore supply, Boliden has now taken the second generation of the fully­autogenous grinding concept on stream, Using new design and a highly-developed process control system the benefits of conventional two stage autogenous grinding technology are obtained with a wide range of ore types. The APC grinding system has been developed further. A new design of the Boliden Pebble Extractor together with an advanced control strategy make the performance of the APC concept superior to all other grinding systems with any ore quality. The capacity and simplicity of the autogenous grinding concept is equivalent to the best SAG installations but the operational costs are up to 25 % lower than for SAG or other primary ball or rod mill systems. The concept is as flexible as conventional crushing and rod mill installations but investment and operating costs are of the order of 25 % lower. Also, from the metallurgical point of view, the different types of autogenous grinding system outperform all other comminution systems including SAG. From 1989 to 1991 four fully autogenous grinding sections have been installed at various concentrators at the Boliden company. Old crushing plants and rod and pebble grinding circuits have finally been replaced by highly productive and cost-efficient autogenous grinding equipment. Significant savings in operational costs have already been reported. Power consumption and maintenance costs have been reduced significantly. Productivity expressed as milled tonnes per operator has been improved. Metallurgical results have developed favourably.

Jan 1, 1992

By J. W. Stevenson

The need for a separate ventilation department within the management team was recognized by the management of U. S. Pipe and Foundry before the company was purchased by Jim Walter Corporation in January, 1970. Because the coal beds of the deep underground coal properties owned by Jim Walter Resources lay 1300 to 2200 feet below the surface, efficient mine ventilation practices are essential through shaft openings varying from 16 to 22 feet in diameter. The extremely high methane gas quantity indicated to be in the coal bed because of the depth of cover and documented by various U. S. Bureau of Mines tests and demonstrated by early mining proved the need to implement this early management decision. At U. S. Pipe and Foundry mine ventilation was a function of the Mining Engineering Department with ventilation personnel assigned to the mine receiving their day to day work assignments from the mine manager or mine foreman. At Jim Walter Resources, the General Manager - Ventilation reports to the Senior Vice President, Mining Engineering, who reports directly to the President, Mining Division, Figure 1 (Company Organization Chart). Position descriptions are static; however positions are dynamic and consequently the degree of emphasis of specific duties and responsibilities change depending not only upon the aptitude of the individual performing the job but also upon his ability to meet the needs of his supervisors; and ultimately upon his ability to react to the economic forces directing our society. The following describes the duties and responsibilities of the General Manager - Ventilation, Figure 2.

Jan 1, 1980

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

By Kal V. S. Sastry

Mineral processing simulation has come a long way since its beginning about thirty years ago. With our increased understanding of mineral process systems and the advent of new software and hardware technologies, we can visualize an ideal mineral processing simulator. This paper attempts to identify a number of desirable features of an ideal mineral process simulator and to describe the exciting trends in making such an ideal simulator a reality.

Jan 1, 1992

By George W. Toth

In a recently completed research project for the U.S. Bureau of Mines - Twin Cities Research Center, a computerized costing procedure for uranium in situ leach mining was developed by the NUS Corporation. This costing procedure, termed a cost model, employs a process engineering approach for estimating total project costs as well as equipment and manpower requirements for uranium in situ leaching operations in either Texas or Wyoming. 80th capital and operating costs are generated by the model along with the overall production cost/pound U3O8 subject to a known rate of return. Conversely, rate of return on equity can be solved for, subject to a given price of yellowcake. During the course of the research effort, this cost model was applied 50 typical site conditions in Texas and Wyoming. Sensitivity rests were conducted for numerous key parameters to determine the cost influence attributable to incremental changes In parameter values. The results of these sensitivity tests along with a description of the in situ leaching cost model have been documented as Bureau of Mines, Mineral Research Contract Report No. J019912, "Cost and Sensitivities Analysis for Uranium In Situ Leach Mining," dated March 1981.

Jan 1, 1981

By Greg Blerie

The requirements placed on belt conveyors grow increasingly complicated No longer is it sufficient for the conveyors to merely move material from "Point A" to "Point B. " Now these systems must be able to produce a specified flow, guaranteeing a plant can operate as scheduled without peaks and valleys in material flow and production rate. In addition, the conveying system must provide effective control, to minimize the problems and costs associated with the escape of fugitive material these problems include unscheduled shutdowns, premature equipment failures, regulatory headaches, poor neighbor relations, and health and safety issues. The key to accomplishing these goals is the loading and discharge of the conveyor belts. Fortunately, new designs for the chutes that accomplish conveyor loading and discharge can move material efficiently, without blockages and while minimizing the amount of dust generated This innovation is the development of engineered flow chutes

Jan 1, 2004

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By Terrence J. Stobbe

On the job injuries to the musculoskeletal system are probably the oldest of the industrial safety problems. Long before we had pinchpoints to guard, chemical vapors to ventilate, and noise to enclose, people were getting strains, sprains, and sore backs from their work activities. In spite of the age of the problem, it remains a long way from being solved. The past ten years have seen a significant commitment by the sci¬entific community to understanding the problem. Engineers, scientists, doctors, and epidemi¬ologists have been involved, and as a result, today we have a much better understanding of the problem. The first step in understanding a problem such as this is to explore its history and epidemiology. The research done by Chaffin (1977), Snook (1970), Ayoub (1978), the ILO (1962), and others, led NIOSH to publish its Work Practices Guide for Manual Lifting in 1981. The guide was based on research carried out in general industry, but subsequent research by Stobbe (1983) and Peters (1983) has suggested that the nature of the problems producing injuries in underground mining is the same as in general industry. The problems are more intense in the mining environment.

Jan 1, 1984

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By Reinhard Gnilsen

Ground pillar control in soil and weak rock often represents a critical and sometimes a determining factor for mined underground civil structures. A concept is desirable that minimizes the restrictions possibly imposed by pillar control requirements on geometrical tunnel characteristics and on the mining operation itself. Conventional concepts are discussed and an alternative concept is introduced. This concept reduces pillar control requirements to ground control measures required with "regular" tunnels. The conventional model of pillar mechanics with potential yielding of a ground body in more than one direction, is then avoided. Due to the complexity of pillar mechanics, the level of engineered design furnished to the contractor is crucial to optimizing ground pillar control. Conventional versus alternative contractual arrangements for pillar control are described and their important role is illustrated. The concept introduced relates to principles inherent to the New Austrian Tunneling Method (NATM). However, tunnel projects using other mining concepts can employ alternative ground pillar control principles as well, if certain criteria are observed. Case histories in the United States and abroad are presented and the impacts from different concepts of ground pillar control are illustrated. The paper concludes by analyzing concept characteristics that can infer monetary impacts on both the owner and the contractor.

Jan 1, 1987

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By Francis X. McCullough

After OSHA published a Notice of Proposed Rulemaking on August 5, 1983, to revise its standards for Underground Construction, many contractors and their representative associations became concerned by the sweeping changes in the proposed rule. After reviewing all of the evidence and testimony on file with OSHA, the contractors presented extensive written and oral testimony to the Department of Labor in Washington, D. C. to help insure that the final published rule would be effective without jeopardizing the economic viability of the industry. The results of those efforts, the entire OSHA rulemaking process, and the opportunity for the construction industry to participate in that process will be discussed.

Jan 1, 1985

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By Ronald P. Wright

ARAMIDS UNDERGROUND COAL MINING

Jan 1, 1993

By William Mayrsohn

INTRODUCTION The net smelter return (NSR) calculations made on various smelter-refiner alternatives, is usually done by taking the gross metal value less metal deductions, smelter-refiner charges and transportation-insurance costs. An important further step in the calculations is the financial charges imputed by refining time, transportation delays, to the time gold is returned (if tolled) or paid for if bought by the refiner. Metal that is priced in advance of payment also requires a forward premium that the mine may or may not be getting. This is a hidden cost that is often omitted from the calculations. Segmentation of each of the above costs are vital to see where improvements can be made through negotiations, better choice of metal pricing or transportation alternatives. BASIC NSR CALCULATIONS SMELTER-REFINER CHARGES Payable Metals - Treatment Refining Charges: Since these can vary from one smelter to another, the effect of a $25 per ounce price increase/decrease should be calculated and kept in mind. This effect is compared to differences in refining/treatment charge and a total smelter/refiner cost on a cost per ounce of dore, gold, or a dry ton of concentrate. Transportation - Insurance: Research has to be done on transportation alternatives perhaps with some assistance from the smelters, railroads or trucking companies. For dore, the U.S. postal service is viable and inexpensive. For railroads, deal with the regional office ie., B&N El Paso, if production warrants regular bulk shipments. Spot rates tend to be higher. A small mine producing concentrates usually goes to the nearest smelter due to extremely high transportation costs. Here is where a refiner can help. Insurance-Quotes for rates on dore/ concentrates are easily obtainable, but the mine has to shop for the best rates. Your insurance broker is the best source of this information. Differences between Mine and Smelter/Refiners Metal losses can be caused by the following: - Concentrate dry weight differences caused by moisture determination or faulty scales (often at the mine). - Sample bias by poor preparation practices on either side ie., grinding of the sample removing gold; or a poorly mixed concentrate. Dore bullion has no such difficulties.

Jan 1, 1987

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995