Search Documents

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By Dan B. Kivari

A key operation of any milling circuit is grinding. Over the last two decades, large diameter semiautogenous grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Most earlier SAG mills were designed to operate at fixed speeds. Present day SAG mills can operate at a fixed speed or variable speed through the use of an ac synchronous motor or dc motor. This flexibility, however, comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on net present cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors, such as reliability of mill drives and power source, are important elements in the decision making process. This article examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1992

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By Jaye Pickarts, Bret Boster, Jack McPartland

Pegasus Minera de Chile, Ltda. is completing three phases of metallurgical evaluation on the Pullalli project to develop a preliminary process flowsheet. A project feasibility study is in progress. The feasibility study includes a proposed process flowsheet designed based on results from the multiple stages of metallurgical evaluation. Phases I and II of metallurgical evaluation included laboratory scale heap leach and milling cyanidation testwork on multiple drill core composites and bulk ore samples from the Pullalli Project. Phase Ill included pilot scale milling/cyanidation testwork on Pullalli drill core composites. The proposed flowsheet includes selective mining and separate processing of low grade and high grade ores. Low grade ore will be crushed and heap leached. High grade ore will be milled leached for 12 hours in an agitated cyanidation circuit. After 12 hours of leaching, sands and slimes will be separated and the sands will be washed using a counter current cyclone (CCC) circuit. Partially leached and washed sands will be added to the crushed low grade ore for heap leaching treatment and permanent placement. Partially leached slimes will be thickened in a high capacity thickener and will be processed in a CIP circuit. Leached slimes will be placed in a tailings impoundment.

Jan 1, 1996

By Koehler Stout, Leroy Friel

INTRODUCTION Hydraulic sand fills have been extensively used in the United States in deep metal mines since 1940, and hydraulic fills have been placed in coal mines in Europe for many years. Numerous surface hydraulic fills exist in Appalachia for the disposal of coal mine waste and throughout the United States for the disposal of other mining, manufacturing, city, and paper company wastes. Hydraulic fills, as they are now deposited in stopes in mines, are often deposited at near minimum density and hence provide very little support to stope walls and pillars. If the support strength of fills could be increased, perhaps ground conditions in deep mines could be improved making them safer and more efficient. Surface fills deposited at higher densities could be covered with top soil upon which grass could be planted. The purpose of this paper is to describe procedures where the support strength of hydraulic fills can be considerably increased, and the focus of the paper is on applications to deep mines. In deep mines the objective of increased fill strength is to reduce heavy ground problems, improve destressing techniques, reduce or eliminate rock burst incidences, provide better working conditions, provide wall support so that more or all ore pillars can be removed, and improve mine safety, efficiency, and reduce surface environmental problems. The authors have shown that it is possible to improve fill strength used in deep mines. This paper reports the slurry filling procedure, fill testing techniques, and some recommendations for application in deep mines. Some of the reasons for low strength hydraulic fills are:

Jan 1, 1979

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By Scott Burchmore, Jason Emery, Michael Melville

This paper presents best practice data management for monitoring of extensometers in Australian underground coal mines. This work is based on the combined experience of the authors and the available literature. The information and ideas presented herein are a culmination of many years of database development founded from mine site-based ground support design, underground inspections, extensometer data management and data analysis. Each author has more than ten years’ experience as a practicing geotechnical engineer at several operating industry wide research project focused on utilizing mechanical extensometer data for data analytics and machine learning. Principal hazard ground control management plans, stipulated in Australian coal mining legislation, outline the mandatory installation of ground monitoring devices during routine mining activities. After 20+ years of data gathering the barrier to implementing modern data analytics remains the challenges imposed by inconsistent data structure and data quality. This inconsistency is still routinely found between sites, companies and mining regions. Through the relatively simple application of a standardized database structure, the potential to shift from simplistic tracking of trigger levels, siloed at individual sites, to an industry standard method for compilation & comparison of monitoring data is enabled.

Jun 25, 2024

By Luiz Roberto Amaral, Peter Frobenius

Construction of the first phase of the Sao Paulo Metro, the North-South Line, will be completed late in 1974. The downtown section of this line consists of 2.2 miles of 19.6-foot diameter soft ground tunnels and 3 subway stations. The entire tunnel - station package was let to one contractor. A plan and profile of the tunnels and stations is shown on Figure 1. Passage of the tunnels under Boa Vista Street in the Sao Paulo Financial District was one of the major challenges. The street is only 50 feet wide from building line to building line and flanked by 10 to 20 story buildings. The tunnels pass within 4 feet of adjacent footings. Further south, the tunnels run 13 feet below the flat foundations of the Caixa Economica, a massive 11 to 14 story building. Surface settlement had to he limited to less than .07 feet/tunnel and good face control and grouting procedures were essential. For this reason, full face cutting wheel tunneling machines were selected to drive the tunnels south of the Access Shaft Prestes Maia which included Boa Vista Street and the Caixa Economica. The tunnels north of the Access Shaft Prestes Maia were driven under a fairly wide Avenue and greater settlements were permitted. Open face shields were selected to drive these tunnels. Most of the work has now been completed and analyzed. Here are some of the results - Careful planning and execution of tunneling procedures kept surface settlement over the tunnels below a magnitude of .05 feet, allowing tunneling adjacent

Jan 1, 1974

By D. J. McKee, D. M. Wiseman

The usefulness of simulation as a technique for metallurgical process design and optimization studies has been greatly extended over the last few years by the development of a number of general purpose simulation packages. The packages, or simulators, all have the common objective of presenting the mathematical models and simulation methods in a form which is readily usable by plant engineers and metallurgists. To date, most simulators have been concerned with steady state simulation, but packages capable of dynamic simulation are now becoming available. The paper outlines the essential features of versatile steady state and dynamic simulators. Typical applications are presented by considering examples of design and optimization studies. Limitation on the use of simulators are also presented.

Jan 1, 1991

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By Charles R. Nelson

INTRODUCTION The support of openings in weak sandstones can be achieved by spraying on a liquid grout which will soak in and harden to form a shell. In the St. Peter sandstone of the Minneapolis-St. Paul area of Minnesota compressive strength is increased from about 0.7 MPa (100 psi) to over 7 MPa (1000 psi) to depths of 152 mm (6 in.). A shell of this strength and thickness can pro¬vide support much as shotcrete does but at lower cost. If the spray-grouted shell is inadequate for the support needed, it provides a good base for shotcrete application, which is often difficult in weak or friable sand¬stones because the fresh shotcrete peels off along with a thin layer of sandstone. The spray-grouted technique was initially developed at the Civil and Mineral Engineering Dept. of the University of Minnesota using funds provided by RANN Div. of the National Science Foundation. It was used as temporary support in a 3-m (10-ft) wide, 3700-m (12,000-ft) long storm water drain tunnel by the Minneapolis Sewer Construction Dept. Much of the field development at this construction project was carried out with the cooperation of the personnel of the city of Minneapolis. It also was used for temporary support in a 3.3-m (11-ft) wide, 1800-m (6000-ft) long storm water tunnel built in 1978-1980 for the Minnesota Dept. of Transportation in Minneapolis. In 1975, 2000 m (6500 ft) of 1.5-m (5-ft) wide utility tunnels were spray-grouted for final lining. A 50-m (150-ft) long, 1.2-m (4-ft) wide test tunnel built at the university in 1974 was sprayed for half its length and is being observed for long-term behavior which to date (1981) is good. GROUT MATERIALS The requirements for the liquid grout are more severe than those for injection grouting. Besides being able to penetrate the rock and develop sufficient strength, it must have the following properties: (1) be nontoxic, noncombustible, and have a low odor for spraying under¬ground; (2) have controllable viscosity and setting time for adjusting to the permeability of the sandstone and the required depth of penetration; and (3) must "wet" the sandstone and develop capillary "draw" to penetrate to the required depth. A sodium silicate-based grout with the proper setting agent meets these requirements in the local St. Peter sandstone which has a uniform grain size dis¬tribution curve with D,,, = 0.1 mm, permeability of about 10 to 20 darcys, a porosity of about 25%, and less than 5% of silt size or smaller. It is 97 to 99% pure SiO2. The grout mix consists of Philadelphia Quartz Co. Type N sodium silicate and Celtite 55 Terraset Spray Grade (SG) distributed by Celtite Inc., Cleveland, OH. A volume mix ratio of 100:9:125 for sodium silicate to setting agent to water produces a grout with two to four centipoise viscosity, and initial set at 20°C of 20 min. Setting time is temperature dependent, being longer at lower temperatures, but can be adjusted by varying the setting agent concentration a few percentage points. APPLICATION The application is simple. Spray the grout on the surface until the desired penetration is achieved. Penetration rates of about 5 mm (0.2 in.) per min. are realized in the St. Peter sandstone for up to 152 mm (6 in.) of penetration (30 min. of spraying). The set time must be longer than the spraying time. The spray nozzle should be moved back and forth at a rate that minimizes runoff due to surface buildup. Both a single large hand-propelled nozzle and multiple small machine propelled nozzles have been used successfully. The pumping and mixing equipment used consisted of: (1) a hand-held, hand-pumped, 11-L (3-gal) gar¬den sprayer for test patches (mix by shaking); (2) 76-L (20 gal) batch mixing in barrels with small electric pumps for spraying and mixing; (3) two component pumps consisting of Hypro Model 5300 piston pumps (Hypro Pump Co., St. Paul, MN) on a common shaft driven by an electric motor. The sodium silicate is premixed with a portion of the water and the setting agent is mixed with the rest of the water. The two components are combined and mixed just before the nozzle; and (4) a proportioner metering the setting agent just before the nozzle with the water and sodium silicate premixed and pumped from the surface. The proportioner permits the bulk of the grout to be pumped through a single pipe or hose with only the setting agent stored underground. This is efficient and low in cost. COST The grout mix costs about $0.20/L ($0.75 per gal) in 1978 dollars. Filling all the voids 100 mm (4 in.) deep (25% initial porosity) would have a materials cost of about $5.40/m2 ($0.50 per sq ft). The labor cost of application is usually less than the material cost for normal tunnel jobs. A pump and proportioner cost less than $1000. Sodium silicate storage tanks and pip¬ing costs would depend on the particular site conditions. REFERENCES AND BIBLIOGRAPHY Nelson, C. R., 1977, "Spray Grouting for Tunnel Support and Lining," Underground Space, Vol. 1, No. 3, pp. 241¬ 245. Yardley, D. H., Nelson, C. R., Stocker, T. H., 1974, "So¬dium Silicate Spray Impregnation of Tunnels in the St. Peter Sandstone," Research Report, University of Min¬nesota, 118 pp.

Jan 1, 1982

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

By Sean E. Armstrong, Deepak Malhotra

Gold extraction from refractory ores as a percentage of total gold production is increasing. The processing technology options for treating difficult-to-process refractory ores are also increasing. The best processing option is dependent on many factors including feed grade and the cause for ore refractoriness. The causes for ore refractoriness are many foldCpreg-rob­bing, encapsulation in pyrite, arsenopyrite or silica, presence of cyanocides, presence of cyanide-insoluble gold compounds, etc.1. The first step in the process development of a refractory gold deposit is to determine the cause for ore refractoriness. The traditional approach of undertaking detailed mineralogical examination of ore types, major and minor mineral constituents and their association does not necessarily provide the metallur­gist all the information needed for characterization of gold-bear­ing ores. For process development programs it is desirable to complement traditional mineralogical methods with diagnostic leach testing, which attempts to quantify the deportation of gold in various mineral matrices. This paper briefly reviews the diagnostic leaching proce­dures and its applications for a wide range of gold-bearing refractory ores, both primary and by-product.

Jan 1, 1996

By Stuart W. Maher

A major problem in future discoveries of base metals is their "explorability". By this I mean an exploration program must be designed that assures accurate assessment of the potential for ore, but is within reasonable budgetary constraints. As we are compelled to depend more and more on non-outcropping prospects, "blind" deposits, and as drilling costs multiply, the costs of exploration increase significantly. Solutions to the problem of defining exploration targets are influenced by our conceptions of the origin and recognition o f conditions that localize ore. The maxim that "elephants should be sought in elephant country" presumes we can recognize elephant country. This paper presents a suggested origin for some mineral deposits, and their controls; particularly those termed ?Mississippi Valley type". Tennessee is used as an example of the ideas offered. Mining districts designated "Mississippi Valley type" are, and have long been, the principal sources of barite, fluorite, lead and zinc ores in the United States and elsewhere throughout the world. A large volume of literature is available describing this class of ore deposits, explaining their habitat, and invoking genetic models for them. The quality of this literature is notably uneven, some of it demonstrably erroneous, and much of it is restricted to detailed descriptions of one aspect of the problem, or to detailed descriptions of one aspect of the problem, or to a single mine, or even a single stope. If an ore deposit is thought

Jan 1, 1977

By Osamu Shoji, Mamoru Kato

In order to continue improving the quality of telecommunication services to meet the expectations of the people and to increase reliability in the case of emergency such as disasters, Nippon Telegraph and Telephone Public Corporation (NTT) is now constructing cable tunnels which connect main urban telephone offices. However, almost all the large cities in Japan are built in river deltas, so that their chief underground features are low strength fluvial deposit and a high ground water level. In this saturated soft ground, the ground surface at an installation site has occasionally subsided through deep excavations for cable tunneling construction. As these settlements have sometimes caused accidents, especially in densely populated large cities, NTT has made much effort to avoid such accidents. These accidents have occured mainly in flexible sheeting due to its inward movement. Therefore, after the investigation into forecast method of sheeting deflection with accuracy, NTT has reserched a system which forecasts ground surface settlements. This paper describes an outline of the ground settlement forecast system and practical example on the site.

Jan 1, 1979

By Randy Ynchausti

ERIC GUTIERREZ, Knowledgescape: Our next speaker is Randy Ynchausti. He&apos;s the director of development, Knowledgescape systems division, of EIMCO Process Equip- ment Company. The title of Randy&apos;s talk is "An Expert Control System for Phosphate Beneficiation." RANDY YNCHAUSTI: System integration. How does the systems integrator survive when caught between plant engineers, plant management, and third-party engineering firms, and stay within the budget of the corporate goals? I&apos;m not sure that anyone knows how to do all of that on one project. Results are critical when we talk about how systems integrators work with operating people, how the operating people want systems integrators to work with them, and how both groups work together so that at the end of a project, you have been provided with solutions that meet your needs and solve your problems at a fair price. How does the integrator&apos;s role change when working with different types of professionals, such as plant managers, plant engineers, engineering firms, or other system integrators? Finally, what is the dynamics of people working with machines and providing services and solving needs? The average number of employees per pound of copper processed has decreased significantly during the past 15 years. I would dare to generalize and say that the average number of employees per whatever unit of measure we have in whatever industry we work in has decreased over the last 15 years. From a system integrator&apos;s perspective, there are some clients who lack a bit of internal expertise as corporate downsizing occurs, and that&apos;s one reason why we go out to system integrators or third-party vendors and buy things from them to solve our problems. Downsizing really amounts to savings, but more than that, I think Brian expressed this and I agree with him, it also amounts to a cost. Unfortunately, most of us count the savings and none of us count the cost in that approach. It&apos;s easy to count the savings, which is one reason why we count it so quickly. Maybe that also accounts for why we set our pencils down so quickly after we get that dollar value. Maybe we should pick that pencil up every once in awhile and refigure the expense, the cost to us, and determine what we&apos;re going to pay during the next year or two or three in losing that expense, or that staff. A broad experience base accumulated over projects at various plants helps system integrators to provide services to clients. This experience enables the system integrator to

Jan 1, 1998

By K. Burke, G. Zhan, A. Mayer

A cover with capi1lary barrier effects (CCBE) is being constructed an the AA leach pad at the Barrick Goldstrike mine near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study was conducted on a mall-scale test cover placed on the AA leach pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2002

When longwall equipment is being specified, a nominal capacity is generally given on which to base the design of the various face and out-bye systems and components. This capacity generally comes from a nominal annual capacity requirement based on realistic utilization rates. From illustrative examples of simple system simulation, this paper sets out to show that a single nominal capacity is not sufficient to size the different systems. The manner in which the Longwall is operated and the overall system configuration and availability can have a significant impact on overall productivity.

Jan 1, 2008