Search Documents

By Jaroslav Briancin, Katarína Gáborová, María Florencia Márquez-Zavalía, Marcela Achimovičová, Ol’ga Šestinová, Pavel Škácha

Naumannite (Ag,Se), a silver selenide mineral, was first discovered in 1828. This study investigates the structure, morphology, chemical composition, and leaching kinetics of naumannite. Mechanical activation in a planetary ball mill increased its specific surface area, enhancing the leaching rate of silver in nitric acid (HNO3). The study found that mechanical activation significantly improves silver recovery.

Jul 1, 2023

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By R. A. Kirkland

The oxygen consumption method utilises an oxygen sensor to monitor the gas-phase oxygen concentrations in sealed chambers filled with reactive waste rock with subsequent confirmation of the oxygen content by gas chromatography. Results of experiments utilising low sulphide (<0.5w1%) waste rock yielded reproducible oxygen consumption rates on the order of 10-10 mol O2.kg-1. s-1. Petrographic analysis of the waste rock material indicated that the dominant sulphide mineral is pyrite (FeS2). Assuming a stoichiometry of 1.75 moles of O2 per mole of SO4 sulphate release rates were inferred to be between 6 and 18 mg SO4 kg-1 wk-1 Typically these results are 2 to 3 times greater than measured sulphate release rates from humidity cells. Our findings suggest that this techniques offers a rapid. cost efficient method for determining sulphate release rates in waste rock piles, even at low sulphide concentrations.

Jan 1, 2000

By Marc Carriere

Bright-orange couplings adorning piping systems are a common sight in just about every underground mine in North America. Grooved mechanical piping, the pipe-joining system that utilizes these couplings, is the preferred method for joining underground and plant piping systems in the mining industry, due to the ease and speed of installation and maintenance. However, the applications for such systems have traditionally excluded high-pressure systems. Most grooved mechanical couplings have a moderate working-pressure limitation, so high-pressure systems have required the use of alternative joining methods, typically heavy-duty flanges. However, the introduction of high-pressure couplings (up to 4,000 psi) has made the grooved joining method viable, and even preferable, for backfill, deep-mine chilled water and dewatering lines and other high-pressure piping applications. As engineers explore the use of high-pressure couplings, questions will undoubtedly arise about the joining method?s capabilities. This article will address the capabilities and specifications of high-pressure couplings, and compare flanged and grooved mechanical pipe joining in traditional as well as high-pressure underground mining applications.

Jan 1, 2011

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By G. H. Roybal, J. M. Barker

Humate mining in New Mexico is a small industry [455 m3 (16,079 cu yd) valued at $395,894 for 1983] with three mines active in 1985. Either humate (carbonaceous claystones rich in organic matter) or weathered coal ("leonardite") high in humic acid are mined. The humic acid content needed to meet consumer specifications determines which type is mined. The humate and "leonardite" now mined in New Mexico are used primarily as soil conditioners or as drilling mud additives. The potential resource for both are very extensive within the coal-bearing formations of the San Juan Basin in northwest New Mexico.

Jan 1, 1987

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By Allan E. Hall

The use of full face boring machines in underground mining has increased considerably in recent years and over 200 raise-boring machines are now in use in the Western World. Several tunnel-boring machines have been tested notably in America, West Germany, Britain and South Africa. A relatively new concept is the blindhole borer, where the machine stands on the lower level and bores a full diameter raise upwards without the use of a pilot hole. Four of these machines have been tested to date in South African quartzites with varying degrees of success. The development of boring technology has created new problems for ventilation engineers and exacerbated several existing ones. This challenge has been met in many varying ways and this paper attempts to provide a review of the current state of the art. Technology and methods are developing at great speed in this field and therefore no final and absolute solutions can be proposed, since each machine and site pose individual problems which are best handled by local knowledge and experience.

Jan 1, 1980

By Jon Kellar, Samuel Kessinger, Prasoon Diwakar

Tantalum (Ta) and niobium (Nb) are extracted from many different ore types. The major economic orebody mined for tantalum and niobium consists of tantalite ((FeMn)Ta2O5) and columbite ((FeMnNb2O5)) in a solid-solution mineral commonly referred to as “coltan.” The largest supplying region, The Democratic Republic of the Congo (DRC), is unfortunately also the most ethically compromised source for this critical mineral. Officially, the U.S. government has deemed coltan ore from the DRC a “conflict mineral” [1]. The lack of pragmatic and effective local mining regulation in Central Africa, when coupled with high levels of violence and corruption, has spawned a widespread, illegal, unethical and, most importantly, unsafe economy. This illicit economy is centered around first, illegally mining these valuable conflict minerals and second, smuggling these minerals into the global supply chain. Handheld spectroscopy devices could provide further transparency to these opaque supply chains, giving miners, traders and refiners the ability to authenticate the provenance of the minerals they encounter, and allowing companies to prove compliance with the regulatory agencies attempting to curtail illicit mining.

Mar 1, 2025

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council&apos;s Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

By Richard E. Hucko

The U.S. Department of Energy (DOE) Coal Preparation Program focuses on providing the technical and process-development basis that can be utilized to produce environmentally acceptable clean-coal feedstocks for use as market conditions permit. A major objective of the Coal Preparation Program is the development of physical coal-cleaning technologies capable of significant removal of mineral matter and pyritic sulfur at high energy recovery levels.

Jan 1, 1989

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman&apos;s daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today&apos;s highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.&apos;s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative&apos;s 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By D. R. Gibbons

This morning I would like to speak to you about an area of chemistry that is enjoying a revival-organometallic compounds. This renewed interest, principally stimulated by defense needs, has already created new markets for the products of the mineral industry. Although the consumption of metals in these new products is modest at oresent, several hold promise of importance. Because this is a new and growing market, I am sure the Council of Economics is aware of many of its facets and is interested in new developments. Of course, the chemical industry has been a significant consumer of minerals for many years. I estimate that in 1957 the chemical-industry purchased a total of $1175 million worth of minerals as raw materials (not including fuels). This estimate can be broken down as follows: [Metals and metallic minerals $375 million Nonmetallic minerals (excluding hydrocarbons ) 330 million Hydrocarbons 470 million $1175 million]

Jan 1, 1958

The 71st Annual Meeting of the Minnesota Section of SME and the 59th Annual University of Minnesota Mining Symposium were held jointly April 14-16, 1998, in Duluth, MN. Registration was estimated at 450 people, about the same as last year&apos;s attendance. A short course on mine productivity and a trade show that included about 75 exhibitors were also held in conjunction with the SME meeting. This year&apos;s theme was "Iron ore and integrated steel - where are we going?" Although generally optimistic in the near term, the general feeling among the attendees is that the industry faces serious competitive challenges. The iron mining industry in Minnesota experienced a tremendous rebound from the devastating downturn of the 1980s. Today, however, all seven of Minnesota&apos;s taconite plants are operating at full capacity. And these high production levels are expected to continue during the next several years. Longer-term, however, Minnesota&apos;s producers face an increasingly competitive worldwide market, including stiff competition from Canadian operations. Because of the increasing competition, industry representatives in Minnesota believe that it is critical to strengthen their operations. To accomplish this, companies are looking to: ? Further reduce production costs. ? Bring new technologies into their operations. ? Develop value-added facilities such as direct-reduced iron. ? Expand their markets. The industry is also seeking more collaboration between industry and government. The National Steel Pellet Co. and Minntac are looking at using ported kilns, which would reduce energy consumption significantly. Cleveland Cliffs, EVTAC, Northshore Mining and Minnesota Iron and Steel are all looking at building value-added plants. One such project that received attention among the attendees was Minnesota Iron and Steel&apos;s proposed $1.2 billion combined mine, taconite plant, direct reduced iron facility and steel production facility. If the operation is built, it would produce about 3.4 Mt/a (3.39 million ltpy) of direct-reduced iron pellets. Financing is pending. An announcement is expected in the fall of 1998. The pellets, containing 70% iron, would be processed into steel in electric arc furnaces. The steel produced would then be processed into hot-rolled coil, which is used by the appliance and automobile industries. The keynote addresses and technical sessions focused on these issues as well as on environmental issues.

Jan 1, 1998

By Gary Nash

While there could be as many directions on regulations as there are viewpoints surrounding the asbestos controversy, there are a few basic criteria that generally will influence government thinking, namely: - their definition of the problem to be regulated, - their interpretation of the scientific evidence available to them, and - their sensitivities to the views of, and the implications for, various interest groups in society. Clearly, different assessments of these criteria by various governments will lead to differing regulatory regimes. The consequence, of course, is a patchwork of non-conforming regulations among nations, with all that thin implies for the distortion of international trade and the unsettling of international relations. I would therefore argue that when governments are examining regulatory action, they should explicitly take into account their common interests in stable and cordial international relations, and when possible, efforts should be made to ensure that movement on regulation is at least, in principle, in accord with the general views of the international community.

Jan 1, 1984

By Abdullah Arik

The resource classification methodologies have always been a topic of research and debate. There are both traditional and Geostatistical methods used in practice. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for resource classification. Therefore, some practitioners have adapted the methodologies to suit the deposits they are working on, but many simply use the methods they are comfortable with. Another reason for the existence of varying classification methodologies is the lack of an easy and established way to measure the confidence in the estimates. Therefore, their classification becomes a subject of debate. In this paper, a new approach is offered to classify the resources using a "Resource Classification Index." The approach using this index takes into account the local variation, the spatial data configuration around the block being estimated, as well as the traditional distance measures. A case study for a gold deposit is presented to demonstrate how this new index can be used to classify the resources. The results from this approach are compared to those from two popular classification methodologies.

Jan 1, 2002

By Howard E. Mitchell

Modern mechanical raise drilling was first introduced into the United states in 1962. This method of safely, economically raising a shaft has steadily increased in popularity since that time. This steady growth has been largely enhanced by the many advantages to be gained by mechanical raise drilling, as well as by the increasing reliability of the equipment required. It is the purpose of this paper to briefly review the state of the art of raise drilling to include: the various applications and advantages; the equipment requirements, including a comparison of the various types and sizes of machines and rock cutting equipment; equipment performance; and future trends.

Jan 1, 1978

By M. J. Laurila

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA&apos;s Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison&apos;s Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of on-line analyzers (ISO/DIS 15239).

Jan 1, 1999