Search Documents

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By R. Venugopal, T. C. Rao, M. Vanangamudi

Introduction The kinetic approach, to understand a process in detail, has been extensively used in the unit operations of many engineering systems. In green pelletization, the kinetic studies have been mainly oriented towards quantifying the growth mechanism (Kapur and Fuerstenau, 1964; Sastry and Fuerstenau, 1977; Capes and Danckwerts, 1965; Kapur and Fuerstenau, 1966; Kapur, 1972) and in a few cases, relating the rate of growth with added liquid content (Kapur and Fuerstenau, 1964; Newitt and Conway-Jones, 1958). Studies on the kinetics of green pelletization, in terms of the order of the kinetics are virtually non-existent. Sastry and Fuerstenau (1970) classified the agglomeration process into "free in-space" (dilute particle system) and "restricted-in¬space" (highly dispersed particle system) and noted that the former is a second-order process while the latter corresponds to a pseudo first-order rate process. The present paper attempts to describe the kinetics of green pelletization, in terms of order of the kinetics, using pyritiferrous shale as the material system. Experimental Pelletization experiments were carried out using -100 mesh pyritiferrous shale, in a laboratory disc pelletizer, at four intervals of pelletization time (15, 20, 25 and 30 min). The green pellets obtained were size analyzed. The size distribution of pellets has generally been represented by a single parameter such as the mean granule diameter, ratio of maximum and minimum pellet diameter, etc. In the present study, the d50 (50% passing size) of pellets has been considered to represent the size distribution of pellet. Kinetic equations The process of size enlargement is considered analogous to chemical reaction and a general kinetic equation of nth order for growth of pellets is given as

Jan 1, 1990

By M. Bunch

Today?s mine operating managers face an incredible challenge of meeting the forever increasing legal and regulatory requirements for mining projects. Managers know that meeting compliance of these requirements is just a starting point of assuring sustainability for the project. So how do today?s managers meet these requirements while at the same time focus on continuous improvement in Health & Safety, Environmental, Costs & Production, Labor Relations, Social Corporate Responsibility, and Quality? This paper outlines means by which managers can take control of their operation through the implementation of an integrated Business Management System (BMS) and lay the foundation of a continuous improvement culture in their organization.

Jan 1, 2010

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By Val Cachic, Harry M. Castrantas, Craig McKenzie

In April 1986, FMC- Paradise Peak Corporation began milling at the Paradise Peak Mine, which is located eight miles southeast of Gabbs, Nevada. The mill processes about 4DOO tons per day of ore through the mill and cyanide leaching circuit. Gold and silver are recovered via the Merrill-Crowe zinc precipitation process. Tailings are routed to a tailings pond located about one half mile southeast of the mill facility. The pond, lined with 60 mil MDPE, was 25 acres at the start of the cyanide detoxification, covers 90 acres and will ultimately cover 180 acres. Solution is reclaimed from the pond and circulated back to the mill.

Jan 1, 1998

By J. Herbst, K. Fallenius, G. Poling

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

By D. Corrigan, A. Ahmad, R. Sood, J. Bratt, R. Holt

Zinc oxide based electronic ceramics are being used increasingly to protect electric and electronic circuits against transient voltage surges. Varistors are produced by sintering and annealing ZnO based powder compacts through long sintering and annealing cycles. Because of the length of these cycles, a manufacturing plant is saddled with expensive high temperature equipment with low throughput. Ceramics Kingston Inc. has developed a new technology that uses 2.45 GHz microwave energy for sintering and annealing. The new technology has the potential for increasing equipment and labour productivity very considerably. Additionally, the new technology will result in appreciable energy savings and add flexibility to the manufacturing process. Microstructural examination of varistors sintered conventionally and by microwave technology showed considerably smaller grain size in the microwave sintered materials. The electrical properties of the microwave sintered ceramics compare very favorably with those of the ones sintered conventionally.

Jan 1, 1990

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By Peter Joralemon

Introduction The Sierra Nevada Foothill Gold Belt in California extends from Mariposa north for more than 420 km (200 miles). It includes the Grass Valley and Alleghany districts in the zone of Northern Mines and the famous Mother Lode to the south. The gold belt has produced more than 3.1 kt (100 million oz) of gold since its discovery in 1848. This remarkable production, at the present gold price, would be valued at more than $40 billion. The Law of Gambler's Ruin supposes that averages are based on systematic rather than random variations. It emphasizes the vast differences between finite and infinite probability. By applying this Law to this figure, it can be seen that the belt has produced an average of 15.5 t (500,000 oz) of gold per running mile. Many geologists believe, with some justification, that less than half the gold in this belt has been mined. Sixty per cent of the past production has come from lode deposits, the balance from Tertiary and Recent placer gravels. This paper will concern itself with the developing lode mines along the Sierra Nevada Foothill Gold Belt. As a further and final note regarding placer mining along this belt, Mark Twain suggested that placer miners, having lost their senses, had contributed liberally to the population of California's insane asylums. After a 40-year lull with little or no gold production, the lode mines of this famous belt are showing signs of renewed activity. Two open pit mines, the Sonora (Jamestown) and Carson Hill, are now in operation at substantial scales. Two others, the Goldenbell (Pine Tree-Josephine) and the Royal-Mountain King, are being readied for production on equally impressive scales. All are in the southern part of the Mother Lode. Exploration farther north, at Sutter Creek, Drytown, and Georgetown, is showing encouraging results in developing deeper lode deposits. This new activity has been sponsored to a large extent by junior Canadian mining and exploration companies. Most of the established American mining companies have looked the other way, not participating in this important development. One major reason for domestic disinterest in this opportunity is there is little chance for heap leachable open pit ore in this belt, excluding Carson Hill. And heap leaching has become fashionable with American mining companies today. Also, this great old gold belt must have been worked out, for why else is there so little activity here - Catch 22 logic. Another reason is that if a new deposit of size and grade similar to the mines in the past was found, high costs would preclude a profitable operation. And, finally, California environmentalists would not permit mining, even if a rich deposit were found. These may all be pefectly valid reasons not to explore for gold along this belt. But a look at the history of gold mining in California may suggest that the future for exploration and development of the gold resources in the Sierra Nevada Foothills can be greater than the past. It was during the Depression of the 1930s that this gold belt saw its maximum activity, with more than 3000 mines in operation. Some were father and son operations producing only a few tons of ore a day. Other mines employed hundreds of miners to hoist more than 900 t/d (1000 stpd). Some ores were of marginal grade. Others, like the Sixteen to

Jan 7, 1987

By Kathleen Kreiss, A. James Ruttenber

INTRODUCTION Early in the morning of July 16, 1979, there was a breach in the earthen retaining dam of a tailings pond at the United Nuclear Corporation's (UNC's) Church Rock uranium mill. The acidified liquid and tailings slurry spilled through the damaged portion of the retaining wall into an arroyo that is a tributary to the Rio Puerco river system. The Rio Puerco runs through Gallup, New Mexico, and eventually crosses the New Mexico-Arizona border (Fig. 1). On its way to Gallup, the Rio Puerco and its tributaries pass through land with a checkerboard pattern of ownership, with portions owned or leased by the Navajos, individuals, the Bureau of Land Management, and the State. In terms of tailings liquid volume (3.6 x 108L; 94 million gal), the UNC spill ranks as one of the largest. The mass of solids released in the slurry (10.0 x 105 kg; 1 100 tons) appears to be close to the median for accidents of this kind, however [U.S. Nuclear Regulatory Commission (NRC), 1979]. The UNC first opened its Church Rock uranium mill in 1977 on land adjacent to acreage belonging to the Navajo tribe. The mill, which is next to the UNC Church Rock mine, is located approximately 16 km (10 miles) northeast of Gallup, New Mexico (Fig. 1). Gallup, a town of 18 000 people, is the closest population center. The region surrounding the plant site is sparsely populated by Navajos, at a density of approximately 5.8 persons/km2 (15 persons/sq mile). The UNC mill and mines employ approximately 650 persons, and the adjacent Kerr-McGee uranium mine employs about 300. The UNC mill normally processes 3.2 x 106kg/day (3 500 tons/day) of uranium ore, depositing the acidified tailings slurry in a series of three earthen holding ponds. The tailings ponds are located east of the pipeline arroyo that feeds into the Rio Puerco approximately 2.4 km (1.5 miles) from the southernmost tailings dam. The liquid portion of the tailings slurry evaporates in the ponds; hence, under normal conditions, there is no surface flow from the holding ponds to the arroyo. Both runoff from the plant site after heavy rains and possible seepage from the tailings ponds may deliver radionuclides to the arroyo-river system, however. The dam across the southernmost tailings pond was considered to be in keeping with the state of the art. However, the New Mexico Environmental Improvement Division (NMEID) had warned UNC about dangers of locating the pond over a heterogeneous geological formation. The state Engineer's Office approved of the site only after UNC agreed to strict design criteria. Others have pointed to dangers of constructing earthen dams for impoundment of uranium mill tailings (Carter, 1978). Causes of the dam break were multiple: the UNC mill filled the tailings pond to a level that exceeded permit criteria; the tailings pond was lined improperly; the dam was constructed using clay that was compacted excessively, resulting in cracking and subsequent seepage; and the unstable substrate beneath the dam permitted differential settling. The UNC Church Rock mine has continuously released dewatering effluent into the pipeline arroyo at a rate of 88.3 L/sec (1 400 gal/min) since 1968. Before 1975 this effluent was not treated; after 1975 it received precipitation treatment for removal of Ra-226. Radionuclides are also released into the river system through the dewatering of the Kerr-McGee uranium mine 1.6 km (1.0 mile) north of the UNC mill. During usual mining operations, approximately 227 L/sec (3 600 gal/min) are released into the pipeline arroyo and subsequently into the Rio Puerco. The Kerr-McGee mine began continuous release of dewatering effluent in January 1972. In 1974 Kerr-McGee began Ra-226 precipitation treatment of its dewatering releases, but NMEID data indicate that treatment has often been incomplete. The effluent from both mines has been responsible for transforming the downstream portion of the Rio Puerco from a sporadically dry riverbed into a continuously flowing stream and has contributed to the current levels of background radiation along the river system (Table 1). This paper will summarize the postspill monitoring efforts and relate the assessment of this spill to the general question of evaluating the health effects of nuclear fuel-cycle wastes. The data pertaining to the measurement of radionuclides in the Church Rock environment and the radionuclide concentrations in animals will appear in forthcoming reports. CHURCH ROCK HEALTH EFFECTS ASSESSMENT APPROACH The initial health effects evaluation involved identifying the radionuclides that were released into the river system from the tailings pond. Table 1 lists the State of New Mexico maximum permissible radionuclide concentrations for liquids released to unrestricted areas, the typical tailings liquid concentrations, and postspill river water concentrations. The tailings liquid contained comparatively high levels of Th-230, Ra-226, Pb-210, and Po-210--all of which, according to postspill river water samples, had exceeded the state maximum permissible concentrations (MPC) at one time or another. After the radionuclides in the tailings were identified, pathways through which humans could be exposed were clarified. Environmental monitoring data were then used to quantify the important pathways of human exposure. Water samples were collected from the river, from test wells dug near

Jan 1, 1981

By Raj K. Rajamani, Poly K. Songfack

The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then the slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry- free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.

Jan 1, 1995

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By Jon Y. Kaneshiro, John S. Griffith, Anthony F. Stirbys, Mauricio Andrade

This paper presents an overview of the New Mississippi Tunnel Outfall for the Transportation Expansion Project (T-REX). The Outfall conveys highway and other urban drainage to the South Platte River as well as provides long needed relief from flooding problems in the southeastern portion of the Interstate 25 highway corridor. The Outfall tunnel incorporates a one-pass precast concrete segmented liner to convey storm water under I-25 then under Mississippi Avenue to the river. The Outfall crosses both the existing I-25 as well as the future improvements including under the Light Rail Transit, a new bridge abutment, widened lanes, and new retaining walls. The Outfall also crosses adjacent to several buildings and five bridges, under major traffic and utility intersections, and through difficult geology.

Jan 1, 2003

By John B. Jones

New concepts in shaft kiln processing are included in the design of two large diameter shaft kiln plants now under construction. One kiln will be used to produce cement clinker at the Boettcher plant of the Ideal Cement Company at Fort Collins, Colorado. The other kiln is for the semi-commercial oil shale plant for Petrobras, the Brazil National Oil Company at Sao Mateus do Sul, Parana, Brazil. Investigations on application of the new concepts are proceeding in a portable pilot kiln. The shaft kiln has long been recognized as a method of gas-solids contacting having the following principle advantages: l. High thermal efficiency 2. Ability to handle a variety of feed materials with a wide range of particle sizes 3. Minimum investment and operating cost

Jan 1, 1963

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By J. Y. Kim, R. W. Stanley, L. Rosato

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In this study, the flotation response of silver, from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high-acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (AgCu) 2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron, which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1992

By Roland Hoet

Mine operators, conveyor system designers, consultants, and manufacturers have had opportunities over the past decade to utilize various actively controlled technologies to drive complex underground conveyor systems. These technologies included several electrical drive solutions, mechanical drive solutions, and hydromechanical (fluid coupling) drive solutions. All of these technologies have their inherent advantages and disadvantages, and only after several years of operation can mine operators fairly evaluate the overall benefits (short term performance and cost vs. longer term operational and maintenance costs) of any particular drive. Far too often in today's world, decisions for new equipment are made with inadequate regard to issues concerning serviceability and maintainability. Many of the newer electrical technologies (primarily AC variable speed drives) which have been used in recent years were selected based on the perceived desirable benefit from variable speed operation. This technology, however, which differs sign8cantly between various manufacturers, is in a constant state of evolution which puts into question the manufacturers' ability for long-term product support. In addition, various forms of this technology have also generated some undesirable operational issues, including reduced motor life, harmonics for the power system, and mine communications problems. This technology is also extremely current-limited, which results in problems handling overload conditions, a frequent occurrence often resulting from a decline in the coal recovery rate (conveying more rock than coal). The fluid coupling, however, is based on a technology which has been used successfully in underground conveyor applications for decades. Although the base hydrodynamic technology is well proven and has inherently beneficial characteristics on conveyor applications, Voith has continuously improved on this technology to meet the increasing demands of today's challenging conveyor haulage systems. Recognizing a need in the market for a reliable, actively controlled drive system, Voith Turbo began development in 1996 of a new, actively controlled coupling which was targeted specifically for the higher powered, complex underground conveyors. Voith introduced the new TPKL Fill Controlled coupling product to the market in 1997, and the first two applications for this new technology were on multiple drive mpper booster applications on longwall panel conveyors. Since the successful startup of these two conveyor systems in 1998, Voith has supplied over 200 TPKL couplings to the mining industry worldwide, with over 150 in US coal mining applications alone. This paper will provide an overview of the TPKL's capabilities, performance, and reliability based on the TPKL's impressive installation base and operational history.

Jan 1, 2004

By Phillip J. Maddex

During the last 10 years there have been many new developments in transport and handling equipment. Important technical and economic developments that can be used to reduce costs are; new terminal and materials handling concepts large river tows - 40,000 tons and 9000 hp towboats slurry loading and unloading of ocean vessels long distance pipelining of solids development of the shuttle train (unit train) large ocean barges ? 25,000+ tons ? pushed & towed 150,000 ton self-unloading super tankers - 300,000+ tons container shipping Some of these developments have been discussed at SME meetings in papers describing the transportation of minerals from new mines. But, only a few papers described improved transportation from older operations. Since transportation is a major part of the delivered cost for minerals, the economic benefits to be gained by putting new transportation developments to work are very substantial. Frequently good transportation planning and management makes the difference between a marginal ore body and a very profitable one.

Jan 1, 1972

By Robert E. Mead

During the past three years the New York Trap Rock Corporation has been restricting blasting operations to days when favorable atmospheric conditions prevailed. By favorable atmospheric conditions is meant the absence of temperature inversions or isothermals in the lower atmosphere or under 6,000 feet altitude. Strong wind and wind shear can also cause conditions unfavorable for blasting. As a result of this practice, there has been a marked decrease in the number of blasting complaints received. The New York Trap Rock Corporation operates four stone quarries on or near the Hudson River within 60 miles of New York City. The Company supplies approximately 7,080,000 tons of high grade, crushed and graded aggregate, rip rap and by-products to the New Pork City area annually, This stone is carried to the market by a fleet of company owned deck &cows which are moved by tugs of a subsidiary towing company. Stone from two of the quarries is diabase: and, from the remaining two, dolomite.

Jan 1, 1962

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976