Search Documents

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By Ward Sumner

The Jones Hill prospect is a Proterozoic age, volcanogenic, semi-massive to massive sulfide deposit. The deposit is located on the western edge of the Pecos greenstone belt in the southern Sangre de Cristo Mountains of northern New Mexico. The prospect is found in a block (West Block) of meta- igneous rocks, primarily diabase, metavolcanic rocks, and metasedimentary rocks (fig. 1). This assemblage is typical of lithologies found in the greenstone belt. Metamorphic grade is greenschist to lower amphibolite. The West Block is bound- ed on the west by Proterozoic age (1.7-1.4 b.y. by Rb/Sr), granitic plutons collectively called the Embudo granite, and on the east by Paleozoic sedimentary rocks, primarily sandstones, shales, and limestones of Mississippian and Pennsylvanian age. The mineralization occurs in a single horizon which has been overturned and cut into two blocks by a high-angle reverse fault (fig. 2). The mineralized horizon is found at the contact of felsic metavolcanic and rnetavolcaniclastic rocks with overlying intermediate metasedimentary rocks. The local stratigraphic sec- tion from bottom to top is as follows: 1) porphyroblastic quartz- sericite schist (originally a rhyolitic, subvolcanic intrusive); 2) quartz-sericite-chlorite-biotite schist (felsic metavolcanic and metavolcaniclastic rocks); 3) chlorite-talc-biotite-sulfide schist (altered felsic metavolcanic rocks); 4) carbonate-quartz-sulfide [ ] chlorite-tremolite-talc schist (mineralized exhalite); 5) quartz- chlorite schist (silicified tuff); and 6) amphibole-chlorite-feldspar- biotite schist (occasional mafic to intermediate metavolcanic flows).

Jan 1, 2013

By Rennie B. Kaunda, Robert J. Sterrett

Some people in the mining-engineering field mistakenly believe that mine-water management primarily revolves around the treatment of mine waters that fail to meet applicable water-quality standards. While water-quality control is undoubtedly important, it represents only a fraction of what constitutes comprehensive site-wide, minewater management. A more holistic perspective recognizes that it also involves mine dewatering to maintain safe and workable conditions, securing sufficient water supply for operations, strategically handling surface water within and surrounding the openpit to prevent issues like flooding, developing robust post-closure plans to mitigate long-term environmental effects, and proactively minimizing any adverse impacts on local communities and ecosystems. This article provides a brief overview of topics that fall within the concepts of mine-water management. The focus is on openpit mines, as they are generally larger than underground mines. The management of mine water is highly dependent on local and regional climate such as tropical, desert or temperate climate. Each climatic setting has its own unique challenges, but there are also commonalities.

Jun 1, 2025

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By Kurt Wiener

A major process control system is in some ways like a complex organism. The extremities, (that is, field instruments) are exposed to many hazards and suffer malfunctions of relatively minor and repetitive nature. Here I equate a stuck valve or dead transmitter with a skin abrasion or cut. The maintenance and repair of the extremities can be done by technicians with basic but thorough knowledge of relatively few problems and their solutions. Here I equate with administering Band-Aids and aspirin. On the other extreme, when the master control device (such as a computer) fails, one does not attempt home remedies. A "brain" specialist is called in. It is, however, crucial that the patient be able to clearly describe his symptoms. Getting down to the case at hand, a complex system consisting of field instruments, instrument racks, interface equipment, and perhaps a computer, may require maintenance at all levels. At the field equipment end where physical damage, corrosive atmospheres, reconfiguration, and routine calibration checks are common, the customer has the opportunity to develop a competent staff of maintenance people. The relatively high maintenance activity assures competence through repetition.

Jan 1, 1980

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By Robert E. Barrett

The history of mine safety legislation in this country is also a history of mine explosions. Nearly every piece of safety legislation that has been introduced or amended has resulted from some type of a disaster. When coal was first discovered and mined, it was extracted from along outcrops. As the coal became depleted near the surface, underground mining developed. When the first mine penetrated the outcrop, a great number of problems developed, many of which remain with us today. One of those problems is the potential for mine ignitions and explosions. Naturally, when underground mining progressed a few feet into the outcrop, some type of artificial light was needed. Early accounts of mining in Spain, Italy, Japan, and Great Britain indicate that torches served to light the mines. Later, candles were used, and still later, earthern oil lamps containing fish oil were used. As workings got deeper, explosions began to occur. When one did occur it was thought to be the work of goblins or the devil. As explosions became more frequent, it became very obvious that the use of open flames for lighting was very dangerous. A substitute was sought. Dried fish skins which gave off a weak phosphorescent light were tried. A mixture of flour and lime made from oyster shells called Canton phosphorous was also tried unsuccessfully. Fireflies in a bottle were also used.

Jan 1, 1976

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By Robert E. Lovett

The truly educated man is better prepared to meet the challenge of the times. This challenge can be either beneficial or harmful depending upon one s orientation, Certainly man can no longer continue in the way of his father or even in the manner of his own previous experience as he seeks self-fulfillment, unless he is willing to sacrifice inner integrity--unless he is willing to compromise self-determination and self-expression. He must make a choice as society moves rapidly into high gear in the areas of automation and cybernetics. Industry, a unit of society, has a high stake in meeting this challenge, The better prepared and more mature its personnel, the better the end result as it attempts to meet the challenge. It therefore has a vital concern in proper training of such personnel, that their contribution will be of maximum quality. The specialized training required demands a broad liberal arts background which gives the individual a wider perspective upon which to base judgment. This greatly aids his development as he enters graduate school or goes directly into industry. In either case, his value to industry is enhanced. It would seem that the small liberal arts college provides the best environment for such a program, Consideration of several factors will, I hope, throw some light on the severity of the problem.

Jan 1, 1966

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968