Search Documents

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Nik Sokol, Eric Sekulski, Leo Weiman-Benitez, Jon Hurt, Shrinidhi Vijayakumar, Phaidra Campbell

The Silicon Valley Clean Water (SVCW) Gravity Pipeline (GP) is the first Progressive Design Build (PDB) tunnel completed in North America. As part of the Regional Environmental Sewer Conveyance Upgrade (RESCU) Program, the tunnel is a key component to replacing and rehabilitating components of the existing conveyance system in San Mateo County, California. The GP consists of a large diameter Fiberglass Reinforced Polymer Mortar (FRPM) pipe installed inside a 4.1 m (13.5 ft) inside diameter, 5.3 km (3.3 mile) long precast concrete segmentally lined tunnel. The tunnel was constructed using a 4.6 m (15.2 ft) diameter Earth Pressure Balance (EPB) Tunnel Boring Machine (TBM) through heterogenous silts, clays and sands. Construction included two separate TBMlaunches from a centrally located access shaft, and a tunnel alignment below but in close proximity to very soft Young Bay Mud. Settlement criteria and mitigation strategies focused on protection of an existing 1.42 m (56 inch) diameter force main and adjoining structures along the alignment. This paper discusses the results of the theoretical settlement analysis versus the actual observed ground movements, while also presenting mitigation measures and adjustments made during tunneling to reduce the risks of adverse settlement.

Jun 13, 2023

By Otto Braach, Wolfgang Frietzsche, Erdogan Gürkan

The Westerschelde Tunnel is located in the south of the Netherlands and links the two parts of the Provinces of Zeeland, Zeeuws-Vlaanderen and Zuid-Beveland, which are separated by the Westerschelde. Road traf?c has up till now taken the detour via Belgium or crossed by ferry. This unsatisfactory transport link signifies major economic disadvantages above all for Zeeuws-Vlaanderen. The first fixed link for road traffic between the communities of Terneuzen and Borsele are to be created by means of the two 6.6 km long tunnel tubes down to 65 m below sea level.

Jan 1, 2003

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By Anuradha Khetwal, Tala Tahernia

The estimation of TBM utilization rate can be problematic due to the uncertainty involved in the tunneling system reaction to various geology along the tunnel. Moreover, the impact of operational and management issues on TBM performance is unsettled. This includes the occurrence and duration of downtimes and the uniqueness of projects relative to the geology, machine type, backup system, site setup, crew experience, and operational restrictions imposed on the project by localities. The CSM2020 is a model based on discrete event simulation that predicts machine utilization for single or double shield TBM. This model was developed by the Earth Mechanics Institute (EMI) team, using the database of tunneling activities which was compiled based on field observation and measurements in pertinent projects. In the current study, CSM2020 was modified to simulate the workflow of slurry TBMs. The operating principle of slurry shield TBMs is different than open-mode TBMs. The model was verified by comparing results with a recently completed project in the United States. As a result, the model offers reliable utilization rate estimation in different types of TBM by implementing appropriate workflow.

Dec 1, 2022

Rest potential, cyclic voltammetry and chronoamperometry measurements were made to study the effects of cathodic polarization of chalcopyrite simulating the mineral contacted with grinding media under a nitrogen atmosphere. The reaction products on the chalcopyrite surface were identified by XPS and the mechanism of the cathodic reaction was proposed. Micro-flotation tests were performed to investigate the effects of surface changes on the floatability of chalcopyrite.

Jan 1, 1991

By Slobodan Vujic, Goran Cirovic, Dragan Radojevic

Mine production systems (MPS) are characterized, more or less, by the following properties: uncertainty, subjectivity, impreciseness, polysemy, instability, indefiniteness and lack of data. From modern study aspect these MPS mathematically belong to the class of fuzzy systems. With this in mind, the usage of fuzzy sets is recommended as a methodology that treats impreciseness, indefiniteness and complexity of mine production systems in a satisfactory manner. Fuzzy modelling, discussed in this pa- per, is applied as a mathematical implement. The objective of the paper was to show production optimization in practice on the ex- ample of bauxite open pits where fuzzy linear programming (FLP) was used following the criterion per income. The variables in criterion function are linguistic variables while both variables and variable restrictions are presented by triangular fuzzy numbers (TFN). The term "satisfactory income" presented through triangle fuzzy numbers was introduced instead of "maximizing the income". sensitivity of the obtained solutions has been analysed

Jan 1, 1996

By R. L. Grayson

As the total cost of labor has significantly increased over the past ten years, older underground mines have found it more difficult to compete- in a limited demand coal market. Many of the older mines were developed extensively into a reserve requiring a large number of workers to maintain and rehabilitate extensive track haulages and/or belt conveyor systems. Often, a large number of fans were required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. This paper focuses upon problems which beset one such coal mine and projects undertaken to restore it to potential profitability.

Jan 1, 1986

By F. Villanueva Araya

Compania Minera Disputada de las Condes (CMD), an Exxon Affiliate stewarded by Exxon Coal and Minerals Company, operates two' copper mines and concentrators in Chile. Pilot plant studies were initiated in 1984 using a 0.46 meter and a 0.91 meter diameter column for the cleaning of copper concentrate. This eventually resulted in the design and operation of a rectangular column with an area of 6.8 m2, increasing the final copper concentrate grade from about 30% to almost 32'1. Cu without any loss in copper recovery. Evaluation studies of a commercial bubble generator as against the previously used filter cloth air sparger are now in progress.

Jan 1, 1990

By Eugene R. Palowitch, Albert W. Deurbrouck, Thomas H. Parrsons

INTRODUCTION Hydraulic concentrators utilize the physical characteristics-size, shape, and specific gravity-of particles suspended in a fluid medium to effect a concentration of desired quality. Fine-coal concentrators include generally those devices which are used to clean roughly 3/4, in. (9.5 mm) top-size coals. While this size designation is somewhat arbitrary, it is consistent with current practice although some fine- coal concentrators can treat coarser coals effectively. A variety of devices have been and are currently being used to wash fine coals and include: dense media cyclones, wet concentrating tables, hydrocyclones, jigs, spirals, launders, and upward-current classifiers. As launders and upward-current classifiers have been replaced by more efficient devices, they no longer warrant consideration as fine-coal washers. And as fine-coal jigs were addressed with the Baum jig under Part 1, Section 2, and heavy media cyclones and hydrocyclones were addressed under Part 2, Section 1, of this Chapter, only the wet concentrating table and the spiral concentrator will be discussed here. WET CONCENTRATING TABLES History The current wet concentrating table evolved from continuous belt concentrators which utilized a flowing film of water to recover heavy metals. In these devices the heavier concentrate moved up the inclined plane of the belt while the lighter impurities were washed away by water flowing down the belt. The natural outgrowth of the continuous belt concentrator was the vanner, a vibrating endless belt which was first developed about 1860 by Hartwig. Later models of the vanner, such as the Frue, incorporated oscillation in a plane transverse to the direction of the water current. Excellent descriptions of these washers are found in The Cleaning of Coal, by Chapman and Mott.80 Further development of tables included the circular stationary table (Linkenbach), the multiple round table (Anaconda-Evans), the bumping table (Campbell), and finally the differential-motion table which is now used extensively for cleaning fine coals.

Jan 1, 1991

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

By Sebastian Avalos, Julian M. Ortiz, Willy Kracht

Semi-autogenous grinding mills play a critical role in the processing stage of many mining operations. They are also one of the most intensive energy consumers of the entire process. Current forecasting techniques of energy consumption base their inferences on feeding ore mineralogical features, SAG dimensions, and operational variables. Experts recognize their capabilities to provide adequate guidelines but also their lack of accuracy when real-time forecasting is desired. As an alternative, we propose the use of real-time operational variables (feed tonnage, bearing pressure, and spindle speed) to forecast the upcoming energy consumption via machine learning and deep learning techniques. Several predictive methods were studied: polynomial regression, k-nearest neighbor, support vector machine, multilayer perceptron, long short-term memory, and gated recurrent units. A step-by-step workflow on how to deal with real datasets, and how to find optimum models and final model selection is presented. In particular, recurrent neural networks achieved the best forecasting metrics in the energy consumption prediction task. The workflow has the potential of being extended to any other temporal and multivariate mineral processing datasets.

Jun 16, 2020

By S. A. Abetel Sabour

In this work, the block theory was applied to determine the safe limit of the angle of face slope at Limestone quarry of Assiut cement company in order to decrease the occurrence of dangerous potential key blocks. Four joint sets were observed and measured at the face. Computer program based on the vector analysis technique was developed to determine the removable block codes. Stereographic projection was also used in this work to determine the removable block codes and to calculate the maximum limit for the angle of dip of the free face, which was found to be 77°.

Jan 1, 1998

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993

By C. L. Karr

Researchers at the University of Alabama are investigating artificial intelligence based computer models of mineral processing systems. Two approaches have been found to be particularly effective in developing data-driven computer models. The first approach employs neural networks which are computational paradigms based on the mechanics of the human brain. They are able to extract the basic relationships between input and output variables from large data sets. The second approach combines fuzzy mathematics with genetic algorithms to produce an adaptive modeling system. Fuzzy mathematics provide computers with the capability of manipulating abstract concepts like those which humans use so effectively in decision making. Genetic algorithms are search algorithms that mimic evolutionary processes apparent in nature. Together, these two techniques can be used to produce an effective modeling system. In this paper, the two approaches to modeling are compared and contrasted with respect to accuracy and computational time while used to model three mineral processing systems: (1) a grinding circuit, (2) a hydrocyclone separator, and (3) a flotation circuit.

Jan 1, 1997

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003