Search Documents

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the US Department of Energy. The repository is located at a depth of 655 min the Permian age salt beds of the Salado Formation. The exhaust air from the facility is independently monitored by the Environmental Evaluation Group to verify compliance with regulatory release limits for radioactive materials. A May 1995 video inspection of the exhaust shaft identified fluid migration into the uppermost 25 m of the shaft. Since then, water has been observed flowing in from cracks in the shaft lining between 16and 25 m below surface level at an estimated rate of between 5 and15 m3/d. This water inflow has not only negatively impacted the equipment in the shaft, associated duct-work and monitoring equipment located at the top of the shaft, but also challenged efforts to verify compliance at the WIPP. This paper provides an analysis of these effects.

Jan 1, 2004

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By Daniel A. Wasson

A review of the history of boosters is given with examples of the prominent types that have been made commercially. The performance and design features of protected core boosters are discussed in detail. A new gel booster is discussed with its advantages to the mining industry. Booster size, hole configuration, performance and safety aspects are reviewed. Important features of boostering in above ground and underground blasting are related to an economic analysis. This presentation will cover different types of boosters commonly used in mining. However, for the purpose of this paper a few terms need to be defined to clarify the action of different parts of a priming system. Booster* - "Any unit of explosive or blasting agent to be used in a charged hole for the purpose of perpetuating or intensifying the initial detonation". Primer* - "A unit, package or cartridge' of explosives containing a detonator or detonating cord which is used to transmit detonation to other explosives or blasting agents". Detonator - A device for initiating a detonation from a flame or a small electric current, the former being represented by a fuse cap and the latter an electric blasting cap.

Jan 1, 1981

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

By G. R. Brunskill

The molybdenite flotation plant at Magma Copper Company, San Manuel concentrator has been in operation since 1956. In January of 1980 the plant was converted from a hydrogen peroxide - ferrocyanide process to the current sodium cyanide - sodium hydrosulfide process. This paper is an operational review of Magma Copper Company's molybdenite recovery circuit, column cell flotation experience and use of on- stream x-ray flourescence analysis.

Jan 1, 1985

By Lawrence Tsang, Conrad Ng, Tim Leung, Peter Poon

"The Mined Tunnel is part of the Central-Wan Chai Bypass and Island Eastern Corridor Link (CWB), which is a strategic road along the northshore of Hong Kong Island targeted to alleviate the heavy traffic congestion. The objective of this paper is to review the performance of construction of a 160m long Mined Tunnel with a trinocular cross-section area of 460m3 and a combined span of about 50m underneath the southern approach ramp of the existing Cross Harbour Tunnel (CHT) by sequential excavation method (SEM) in hard rock. Mechanical excavation of tunnel by adopting the New Austrian Tunnelling Method (NATM), together with the application of NGI Q-system allows observational approach and optimization of temporary rock support design. Furthermore, the good performance of optimized rock support and the stability of CHT are confirmed through instrumentation monitoring review. This paper also discusses the selection of different tunnel plant and equipment to achieve the planned rates of tunnelling by mechanical excavation in competent granitic rock. INTRODUCTION The works of the CWB mainly comprise construction of 4.5km dual three-lane trunk road, of which a 3.7km section is a tunnel connecting Rumsey Street Flyover in Central to Island Eastern Corridor at North Point (see Figure 1). The Mined Tunnel runs from the ex-Public Cargo Working Area (ex-PCWA), underneath the existing CHT, and through the Causeway Bay Typhoon Shelter. The Mined Tunnel passes at an oblique angle beneath the southern portal of CHT over a length of some 50m. CHT is the primary sensitive receiver of this project and is utilized with a daily throughput of about 120,000 vehicles that far exceeds the design capacity of 78,000 vehicles per day. Hence it is necessary to choose the most appropriate tunnelling method to preserve the structural integrity of the CHT. Other sensitive receivers in the vicinity include structures to the north of the Mined Tunnel, the Royal Hong Kong Yacht Club (RHKYC); and to the south of the Mined Tunnel, the Police Officers’ Club (POC)."

Jan 1, 2016

By Howard J. Brown

The Lucerne Valley limestone mining district is in the San Bernardino Mountains, one of the major ranges in the Transverse Range Province of southern California. Several large limestone mining operations are present along the north range front in Lucerne Valley, and the area is one of the premier limestone mining districts in the country. Resources are contained in Paleozoic carbonate rocks that are part of a thick late Precambrian and Paleozoic sequence that uncomformably overlies crystalline basement. The district has been affected by multiple episodes of metamorphism and deformation, as well as by a complex sequence of late Cenozoic structural events. Detailed studies, however, have demonstrated that these rocks can be divided into formations correlatable with late Precambrian to Permian strata of the Cordilleran miogeocline. The district is the leading producer of white, high-purity calcium-carbonate products in western North America. Pluess-Staufer (California) Inc. mines and processes high-purity white limestone from extensive deposits, and is one of the largest producers of high-quality limestone fillers and extenders in the western United States. Major factors influencing the genesis of economic carbonate deposits in the district include depositional environment, post-depositional processes such as diagenesis, dolomitization and/or silicification, regional and/or contact metamorphism and associated intrusive activity, faulting, folding, uplift and erosion, and preservation from erosion. Regional geologic studies, detailed geologic mapping, intimate knowledge of stratigraphy, and recognition of complex structural relationships have proven to be invaluable tools in the discovery of high quality calcium carbonate deposits in the district.

Jan 1, 1987

By H. P. Cole

A team of researchers at the University of Kentucky, working under a USBM contract, developed over 65 simulation exercises for teaching and testing problem-solving and decision-making skills to miners and mining engineers. These skills involve both improving judgment and decision making in mine emergencies and enhancing the learning of real-world engineering design principles. The exercises are ideally suited for either latent image format or for computer-aided instruction. Exercise features are summarized, the structure and field testing of typical exercises described, and sample frames of individual exercises presented. Empirical data are summarized that describe the effectiveness of using these short, time-efficient performance tasks that simulate real problems and that provide immediate corrective feedback for teaching and testing critical skills. I

Jan 1, 1991

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By R. E. Doerr

The successful technical demonstration of coarse coal slurry transportation at Consolidation Coal Company&apos;s Loveridge Mine in West Virginia suggests that it is now appropriate to seriously consider this technology in other applications, especially the transport of &apos; coal in surface mining. Early examination indicates that coarse coal slurry transport may be highly competitive with existing haulage systems, depending on a number of factors. These factors are not yet completely defined, but certainly will include production rates, coal physical and chemical properties, terrain, soil conditions, climate, water availability and quality, availability of skilled labor and other economic considerations impacting the existing haulage systems.

Jan 1, 1983

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980&apos;s or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By John A. Reeves

The Coal Creek Preparation Plant is the coal cleaning facility of Mid-Continent Coal and Coke Company. Located three miles west of Redstone, Colorado, and at an elevation of 8,040 feet the preparation plant cleans coal produced at the company&apos;s Dutch Creek Mine and L. S. Wood Mine. (See Fig.1.) Current production is at the rate of 2500 tons per day clean coal. Plant capacity is rated 350 TPH raw coal. Reject rates vary with mining conditions from 8% to 25%. Factors which influenced the design of the coal cleaning facility were the characteristics of the coal, the location in a tourist oriented resort area, and the extreme winters of the area. Lack of areas suitable for settling ponds and the necessity of keeping effluent waters out of the fishing streams dictated a closed circuit plant. Severe winter conditions, which last six to seven months out of the year and temperatures which have dropped to 40° F. below zero on occasions demanded that the plant be totally insulated and enclosed indoors.

Jan 1, 1967

By Eleanore L. Nestlerode, James R. Guilinger

In April. 1990 Addwest Minerals acquired the Phillips Ranch sulfur property. The sulfur deposit, hosted by the Permian Castile anhydrite, occurs as two distinct elongate. parallel orebodies within a series of northeast-trending grabens. After completing a positive feasibility study, based, in part. on successful drilling programs by Addwest Minerals and previous operators, the decision was made to place the property into production. Utilizing an existing on-site kasch plant, plus significant portions of the recently purchased Texasgulf Comanche Creek Frasch plant. Addwest is currently constructing an 800 long ton per day Frasch mining facility.

Jan 1, 1992

By J. Drelick

Among the wide variety of modern surface chemistry analytical techniques, contact angle measurements still remain attractive for wetting characterization of solid surfaces. The captive-bubble and sessile-drop techniques are the most popular methods for the examination of flotation systems. Systematic measurements of advancing and receding contact angles for several three-phase systems using the captive-bubble and sessile-drop techniques show that the contact angle measurements depend on the technique used and may differ significantly for some heterogeneous and rough solid surfaces. Importantly, it was found that these discrepancies in contact angle measurements depend on the bubble (drop) size. Contact angles as measured with the static captive-bubble technique are compared with those measured with the dynamic captive-bubble technique, in which the capture of a bubble at the solid surface results after buoyant transport and attachment The dynamic captive-bubble technique allows for the formation of much smaller bubbles than is possible with the static placement technique in which a bubble is placed at the solid surface with a microsyringe. Although this dynamic technique cannot be recommended for the systematic wetting characterization of solid surfaces, its significant advantage is the ability to examine the contact angle/bubble size relationship over a wide range of bubble sizes, from several micrometers to several millimeters in diameter.

Jan 1, 1995

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870&apos;s with rising national wealth and declined in the 1950&apos;s when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999