Search Documents

By R. J. Good

It is well known that the elimination of impurities such as iron pyrite, shale, clay, silica, etc., from coal, by floatation [Sun, 1954; Aplan, 1983] and selective oil agglomeration [Keller and Burry; 1990] depends on the fact that coal is hydrophobic, and the impurities are hydrophilic. The water contact angle has long been used to evaluate the hydrophobic nature of coal, first by Brady and Gauger (1940), who demonstrated that the contact angle of water on coals increases with rank, and passes through a maximum at about 88% carbon. Brown (1962) found that the contact angle of coal decreased with increasing ash content. Sun, and also Aplan, have reported a direct relationship between values of the contact angle and rank, and have related the contact angle to coal floatability. Horsley and Smith (1951) first demonstrated that the captive bubble contact angle may be used to characterize the hydrophobicity of a coal containing more than 80% carbon DAF, while Parekh and Aplan (1978) have shown that the sessile-drop technique may be used to evaluate the hydrophobicity of coal of any rank.

Jan 1, 1992

By Bright Oppong Afum, Kojo Boakye, Kwaku Boakye

This research developed and simulated a novel multi-indicator Fatigue Detection and Alert System (FDAS) designed to enhance fatigue detection accuracy in mining environments. The system integrates a comprehensive set of inputs: eye blink rate, eye closure duration, yawning frequency, distraction levels, Pre-shift Check-in Scores (Self-report) and Electroencephalography (EEG) Levels. Using MATLAB’s Fuzzy Logic Rule Viewer (FLRV) and Simulink, simulations demonstrated the FDAS’s robust ability to process these diverse physiological and behavioural indicators accurately. It effectively classified operator fatigue into low, moderate, and high fatigue levels, consistently providing appropriate outputs and corresponding intervention recommendations across various mixed-signal scenarios. The system achieved a calculated accuracy of 85.19% across 27 test entries, with a standard deviation of approximately 1.8459, confirming its reliability for real-time fatigue monitoring. These findings highlight the significant potential of this fuzzy logicbased approach to proactively identify early signs of fatigue, substantially enhancing safety and operational efficiency in demanding mining operations.

Feb 22, 2026

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2017

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2018

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By J. A. Holtkamp

Environmental regulation in Mexico has matured dramatically and effectively in the last decade. The gap between environmental regulation in the United States and Mexico is rapidly narrowing, so much so that it is no longer necessarily less burdensome to operate in Mexico from a regulatory perspective. This paper is intended to give a general overview of the system of environmental regulation in Mexico. The actual application of Mexican laws and regulations governing the environment to a specific operation will require a much more detailed review of the applicable environmental standards.

Jan 1, 1994

By C. Vass, A. Noble

"The chemical treatment of mine-influenced waters is a longstanding environmental challenge for many coal operators, particularly in Central Appalachia. Mining conditions in this region present several unique obstacles to meeting NPDES effluent limits. Outlets are often located in remote areas with challenging terrain where conditions do not facilitate the implementation of large-scale commercial treatment systems. Furthermore, maintenance of these systems is often laborious, expensive, and time consuming. Many large mining complexes discharge water from numerous outlets, while using environmental technicians to assess the water quality and treatment regime multiple times per day. As an alternative solution, this paper describes the ongoing research and development of automated chemical treatment systems for mine water discharges. The current work explains the development of a bench-scale prototype that has been used to evaluate various monitoring, notification, and control strategies. Results from this testing are compared to present day practices to show the costs and benefits of implementing an automated treatment and monitoring program. INTRODUCTION Background The National Pollution Discharge Elimination System (NPDES), per Section 402 of the Clean Water Act, requires permitting of all point source discharges from coal mines. This program dictates that all water leaving a permitted boundary, whether it be process water or storm water, must leave through a monitored NPDES outlet. These permitted NPDES discharge points, also denoted outlets, outfalls or monitoring points, must meet a rigorous set of effluent limits to maintain compliance. Common effluent limits monitored by coal companies include but are not limited to iron, manganese, aluminum, total suspended solids (TSS), and pH. Raw mine water is often deficient in meeting these effluent limits, and as a result, various treatment processes are required to bring the water into compliance prior to environmental release. Depending on the mining and geologic conditions, water monitoring and treatment programs can constitute a significant operating cost for the mine operator. In Appalachia, acid mine drainage (AMD) constitutes one of the most significant and widespread water quality challenges that must be treated per NPDES guidelines. AMD is a general lowering of water pH that occurs when water and sulfide minerals interact within oxidizing conditions in coal and metal mining. Acid Rock Drainage (ARD) is a similar term that applies more generally to non-mining causes such as highway construction and other large-scale excavations. Today, mine influenced waters (MIW) is becoming more popular as the general term referring to all types of mining-induced water issues. AMD has been researched substantially over the last 30 years, with investigators studying various causal mechanisms and treatment strategies (e.g. Gazea, 1996; Ziemkiewicz, 1998; Skousen, 2000; Kleinmann, 2001; Johnson, 2003; Akcil, 2006; Kalin, 2006). This research has produced several pragmatic results, which provide numerous methods to predict, prevent, and treat AMD."

Jan 1, 2016

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By Charles J. Johnson

The United States is totally dependent on imports for all primary chromite and most ferrochrome supplies. Although the United States imports chromite and ferrochrome from a number of countries, the long-term future of chromite supplies appears to lie in southern Africa (Republic of South Africa and Zimbabwe) where 88 percent of known world reserves exist. Floreover, low mining costs and the availability of low-cost electricity for ferrochrome production gives South Africa a comparative advantage over most other chromite and ferrochrome-producing nations. A well-known problem faced by the United States is that when viewed from a longer-term perspective, the major sources of supply of metallurgical grade chromite and ferrochrome may be subject to disruption. The three countries that have caused the greatest concern have been the Republic of South Africa, the Soviet Union, and Zimbabwe. South Africa presents a particularly difficult problem because it may be subject to internal political unrest and/or U. N, economic sanctions. South Africa has increased its share of world chromium production from about 30 percent in 1968 to 62 percent in 1978.1

Jan 1, 1982