Search Documents

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By B. M. Davis

The uncertainty associated with a reserve estimate has generally been expressed as a subjective ranking rather than a quantitative expression of either reliability or uncertainty. These rankings of estimate reliability have taken a very nonquantitative bent as well. For example, the U.S. Securities and Exchange Commission definition of proven reserves is given as: Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings, or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well-defined that size, shape, depth and mineral content of reserves are well-established. (U.S. SEC, Form S-18, Item 17A)

Jan 1, 1992

By G. Ahuja

Tests were conducted to investigate the effects of cyclone geometry, operating conditions, and particle size on magnetite classification. The effects of these parameters on the partition curve for narrow size fractions were studied using a 25mm diameter cyclone cleaning -150 µ m coal. Additional tests were run to investigate the effects of geometry and operating conditions on the slurry, solid, and water splits. The relationship between the relative density of the underflow stream and the relative density of separation was also investigated. This paper presents the results from this study.

Jan 1, 1994

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By James Charles McHardy

During 1980-2000, the Florida Phosphate industry will deplete its Central Florida Polk County reserves. As a result, new mines will be built in the ?so-called? Southern Florida Reserve areas. These new mines will require new mining, beneficiation and tailings disposal technologies in that the southern reserves have different characteristics than have been encountered in the Central Florida deposits furthermore, government regulations will necessitate the development of new tailings and clay disposal methods. This paper reviews these challenges for the phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1981

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By C. Richard Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (United States, Canada), better geological prospects (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This article does not cover the aluminum industry oligopoly, which is multinational in character. Nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free trade treaty will reverse that investment flow. Cross-border investments The following examples should dispel any doubts about the significance of cross-border investment in the Pacific Rim. BHP, Australia's largest public company, has invested $US 4.5 billion in the JS for the following transactions 1984 $2 billion Utah Minerals 1984 $500 million Energy Resources 1985 $745 million Monsanto Oil 1987 $400 million 50.7% Hamilton Oil 1989 $378 million Pacific Resources Placer Dome, mainly through 76% owned Placer Pacific, has the following gold mine developments in hand including the date the project began, Placer Dome's ownership, project name, its location, and capital expenditures: • 1985, 53.1 %, Kidston, Queensland, $A 139 million; • 1989, 37.9%, Big Bell, Western Australia, $A135 million; • 1989, 60.6%, Misima, Papua New Guinea, $C252 million; • 1990,45.5%, Granny Smith, Western Australia, $A95 million; • 1991, 50%, La Coipa, Chile, $US276 million; and • 1991, 25.3%, Porgera, Papua New Guinea, $C1.1 billion. Australia's Western Mining Corp. (WMC), through a foray of off-market acquisitions in late 1987, acquired con¬trol of five Canadian gold companies for a $A488-million outlay ($C452 million) as follows:

Jan 1, 1990

By M. H. Bolu

Since undergoing a major mill expansion in 1979, Canada Tungsten Mining Corporation Limited has successfully operated a somewhat unconventional rod mill/rod mill grinding circuit at its mill in Tungsten, N.W.T., Canada. The concentrator employs two rod mills in series, of unmatched size and horsepower, for production of feed to a gravity (tabling) circuit. Cyclones and screens are closed circuited with the secondary rod mill. Outlined in this paper are the rationale behind, and consequences of operation of this unusual grinding and classification configuration.

Jan 1, 1984

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By Dan S. Nilsson

When an open pit mine is deepened, more and more waste rock must normally be removed. Techniques for optimization of open pit design are well-established within the mining industry. The recommended method is to choose the open pit alternative with the highest net present capital value of open pit and future underground mining. When the open pit is mined out, the operation must be closed, or, if it is profitable, mining must start underground. When planning an underground operation we experience the same type of optimization problem that occurs when determining the optimal depth for open pit mining. When mining underground the ore body is often divided into a number of areas, blocks or slices, each containing a transportation system with trains, trucks, conveyors, etc. When all the ore within such a part of the deposit is extracted, the operation must be closed, or, if it is profitable, a new transportation must be developed. The question that now arises is: how large a pan of a deposit shall be included in the first development and how much shall be left for future consideration?

Jan 1, 1981

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By A. L. Hauff

As US Coal producers are looking more and more to the international markets, they face the complex job of planning and managing transportation logistics which make effective use of production capabilities, considers the various contract requirements to be fulfilled, Train, Truck and Vessel capacities, port restraints, etc. Pulling all the necessary pieces of information together to allow proper planning throughout the supply chain is often a time consuming, manual but necessary task. This paper will discuss the various constraints, requirements and considerations to supplying coal to a global market.

Jan 1, 2012

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990