Search Documents

By T. Carl Jr. Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors.

Jan 1, 1981

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs' minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996

By Rudolf E. Pfister

One of the Swiss transalpine highways includes two remarkable tunnels: the 16.3 km long Gotthard Road Tunnel and the 9.3 km long twin tube Seelisberg Tunnel, both presently under construction. Large diameter shafts up to 900 m long are required for ventilation. Excavation techniques for rock formations ranging from loose sedimentary rock to granite and very hard siliceous limestone were carefully evaluated. The methods finally applied include excavation of shafts in hard rock, conventional drilling and blasting, excavation by ripper-tooth excavator ("Big John") in marlstone, shield protected heading in loose material and soft rock, and tunnel and shaft lining, both by poured concrete and by prefabricated elements. A critical review of the success of these methods can now be made after a five year construction period.

Jan 1, 1976

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The effectiveness of the grouting of saturated, fractured rock in the vicinity of underground workings depends to a great extent on the correct interpretation of the specific hydrogeological conditions at the site. During the planning of grouting operations, calculations of the hydrogeologic co-efficients and of the parameters of the isolating grout curtain(s) and the procedures for forming the curtain(s) must be based on valid hydrogeologic characteristics of the fracture system of the rock within each hydrostratigraphic unit (Anon., 1976). This chapter presents a discussion of the background information that must be collected for these purposes. Details of testing are presented in Chapter 3. The general design of new or the reconstruction of existing underground workings requires a broadly based organization having the expertise to develop a grouting operations plan once it acquires the necessary information. The needed information includes: 1) general information about the hydrogeologic section, 2) the engineering design of the underground workings, 3) the geology of the region, 4) the hydrochemistry of the ground water, 5) the hydraulic properties of the rock, 6) the characterization of all gases present, and 7) characterization of the rock's physical-mechanical properties which is necessary to avoid or control hydrofracturing . The geological documentation portion of the hydrogeological investigation is prepared based on the results of geologic mapping, geophysical surveys and on geo-exploratory operations at a regional and local scale. Geological data from the excavation of other underground workings in adjacent areas of the region is also included. Finally the results of site specific investigations in boreholes constructed at the site of the proposed underground activity are incorporated. A section of the preliminary report entitled "General Information about the Project Site" patterned after the parent STG guidance document on this subject must be com- piled based on the contents of geological reports and on the general construction plan for a new project or the plan for reconstruction of an existing operation. This section of the preliminary report must contain concise information about the conditions under which the planned grouting operations are to be conducted. The information must cover the geo- graphic, administrative, and economic subject areas also. Information about sources of electrical power, heat and water supplies, the presence and characteristics of local construction materials suitable for making grout (particularly clay and cement for the clay-based grout), transportation, and the status of communication lines and other services must be included in this section. Map scales for this section should be on the order of 1:25,000. The technical characterization of planned underground workings is presented in a project report chapter called "General Construction Plan for a New or the Restoration of an Old Operation. " The characterization comprises concise information about the purpose of the workings, the planned depths (for shafts) and the length (for horizontal and inclined workings), the inside and excavated diameters (for shafts), the cross-sectional area (for inclined and horizontal workings), and the face and mouth markers. If excavated underground workings exist in the region, then a concise description of them must be provided. The characterization of all excavations and all operational conditions must be specified. The location within the general structure of the proposed operation is specified. Flow charts must be included in this section that show: 1) the plan for opening the deposit, 2) the plans of the mining operations, and 3) the planned geological sections as they relate to the main workings. These graphical flow charts and appendices are drawn in scales of 1:2000 or 1:5000. 2.1 GEOLOGICAL CHARACTERIZATION The geological characterization of a site of proposed underground workings includes the following principal subject areas: stratigraphy, lithology, structural geology and a characterization of the status of fracturing. 2.1.1 STRATIGRAPHY AND LITHOLOGY A description of the geological section of the rocks to be intersected by the planned underground workings is complied on the basis of: 1) research data derived from core extracted from exploratory boreholes and monitoring boreholes, 2) the documentation and mapping of all natural out- crops in the region, 3) the data from all existing under-ground workings in the regions where operations are being canied out already, along with data from adjacent regions, 4) the data from surface and borehole geophysical investigations (standard and specially developed logging methods, and 5) regional stratigraphy. The geological description of the rock must express the maximum detail possible. The description provides the name of the rock, the granulometric composition (for fragmented rock), the composition and type of stratification, the drilling characteristics of the rock, a visual estimate of porosity and density for each stratum identified, the karstic

Jan 1, 1993

American Barrick Resources Corp. has come farther, faster in the last 11 years than any mining company in recent memory. Acquisition of Lac Minerals Ltd. in August 1994 now makes Barrick the largest gold producer in the world outside South Africa. In terms of market capitalization, the company is the world's most valued gold producer. American Barrick's 28.3-km2 (7000acre) Goldstrike property on Nevada's Carlin Trend, the primary engine for past growth, was purchased in 1987 for $62 million. Regarded as an attractive exploration target, Goldstrike instead propelled American Barrick to the front rank of world gold producers. In 1993, the company produced 50.75 t (1,631,988 oz), 44.78 t (1,439,929 oz) from Goldstrike. Reserves on the property totaled 905 t (29.1 million oz) at the end of 1993, the largest in North America.

Jan 1, 1994

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970

By L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond stripping shovels and draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping shovels and draglines were also re-examined. The results provide an estimate of equipment diggability and encourage versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating general excavating, loading, and stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1990

By C. J. B. Dreyer, H. A. Robinson

Only South Africa can be considered in terms of resources of amphibole asbestos. There are two asbestos producing fields, one in the Northern Cape Province (producing only crocidolite), and one in the Eastern Transvaal (producing only amosite). This chapter discusses the banded ironstone sequence in which amphibole asbestos occurs, and the genesis of the fiber is briefly reviewed. Also, the properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300 000 t of arnosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production chat could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. The mining methods are also reviewed and evaluation techniques are discussed. The only two types of amphibole asbestos exploited at present in South Africa are amosite [the white colored amphibole asbestos) and crocidolite (the blue colored asbestos). As is well known, crocidolite has been mined in South Africa from the early part of this century, and amosite since the early 1930's. Since these dates, asbestos mining has developed into a significant mining industry. The annual production of crocidolite is approximately 170 000 to 200 000 t. and amosite production is in the region of 80 000 to 100 000 t. CLASSIFICATION OF AMPHIBOLE ASBESTOS Four types of amphibole asbestos are produced economically in the world today: (1) crocidolite, the fibrous equivalent of riebeckite, (2) arnosite, the fibrous equivalent of grunerite, (3) trernolite, and (4) anthophylite. The names trernolite and grunerite apply equally to the crystal and fibrous forms of these minerals. For comparison and clarification purposes, the six known varieties of asbestiform minerals known in the world are shown in Table 1. All the asbestos minerals were originally developed as cross fiber seams in veins or fractures, or were controlled by the lithology. Post- fiber effects caused slip, sheared, and folded fiber seams. Crocidolite and amosite occur in banded ironstone of early Proterozoic age of the Transvaal Supergroup. The fiber seams are developed in certain defined lithological units in the banded ironstone sequence. The lithological units have a remarkable lateral persistence with respect to their chemical nature and physical appearance. Vertically, the banded ironstone sequence displays a heterogeneous nature. Commercial Applications The features and properties that make amphibole asbestos commercially attractive are: 1) The long average length of the fibers is good for greater wet strength in composites. 2) The high tensile strength of crocidolite makes it superior to all other types of asbestos. 3) It is characterized by dispersion in most liquid media, particularly amosite in water. 4) Since the surface charge of amosite and crocidolite is negative, the fibers produce an open lattice work in water with a high bulk volume giving excellent filtration rates and rapid drainage in a wet asbestos cement mix. 5) The insulating properties of amphibole asbestos mats are still important, particularly in a corrosive environment, despite the introduction of many other synthetic insulating materials. 6) Corrosion resistance, particularly acid corrosion resistance. 7) Due to the high modulus of amphibole fibers, resins reinforced with these fibers exhibit

Jan 1, 1986

By Francois E. Heuze

This paper summarizes the geomechanics programs conducted in two hard rock underground mining operations in the Western United States, between 1966 and 1981. The two projects were directed towards understanding the behavior of the rock masses, at the scale of the caverns. To this end, the emphasis was put on large scale field measurements, complemented by limited laboratory testing. The results of these observations were used to build realistic finite element models of the underground chambers. In the marble mine, at Crestmore, California, the models were applied to the structural optimization of the room-and-pillar pattern. In the granite mining, at Climax, Nevada Test Site, the models explained some unusual stress changes observed during excavation. Based on the large number of geomechanical techniques employed, specific conclusions and recommendations are offered regarding the quality, applicability, and usefulness of the various methods. The two case histories clearly indicate chat numerical models are extremely useful for a detailed understanding of the structural behavior of mine openings. To be realistic, these models must be based first and foremost on large scale field observations. The lessons Learned on these two projects also are directly applicable to the design and analysis of nuclear waste repositories in hard rocks such as basalt, granite, and welded tuff.

Jan 1, 1982