Search Documents

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By Chester A. Rowland

La conminución de Ios minerales es, generalmente, una etapa de preparación de la alimentación para las subsiguientes etapas del proceso. La molienda, fase de conminución de productos finos, requiere una gran inversión de capital y frecuentemente es el área de máxima utilización de potencia y de materiales resistentes al desgaste. La molienda se produce normalmente en tambores rotativos que utilizan un medio de molienda que se pierde en la misma, al elevarse con la rotación del tambor, se rompe el mineral por combinación de los efectos de impacto, atrición y abrasión, hasta producir el producto especificado. El medio de molienda pueda ser: - El propio mineral (molienda autógena - primaria y secundaria). - Medio no metálico, natural o fabricado (pebbles) - Medio metálico (barras o bolas de acero) Este capítulo tratará de molinos de barras y bolas que utilicen medio metálico de molienda.

Jan 1, 1982

By VIVEK KUMAR HIMANSHU, PK SINGH, AK MISHRA, MP ROY, RAVI SHANKAR

Underground blasting has many challenges. The primary aim of blast designers is to optimize drilling and blasting parameters to deal with the associated challenges. Optimizing these parameters is currently based on various rules of thumb, which have many site-specific limitations. Accordingly, computation of these parameters using empirical rock fragmentation predictors can be useful for blast designers. This paper presents the results of work on burden-spacing determination by back-calculation from the empirical Kuz-Ram model for underground stope ring blasting.

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By D. A. Norrgran, J. A. Marin

Introduction The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic product that was an order of magnitude stronger than that conventional ferrite magnets. This allowed for the design of high-intensity magnetic circuits that operated energy free and that surpassed electromagnets in the strength and effectiveness. New applications and design concepts that focused on the mineral and metal processing industries have evolved. This technology led to the development of various magnetic separators specifically designed for mineral processing applications. Applications that were not previously considered are now being used in primary mineral upgrading, recycling and secondary recovery. Historical perspective Lodestone was the first naturally occurring permanent magnetic material known. Lodstone was most likely used to upgrade iron ore by early civilizations. By the 1600s, the early magnet technology had advanced to quench-hardened iron-carbon alloys. The practical significance of magnetic separation was formally recognized in 1792 when an English patent was issued for separating iron ore by magnetic attraction. By today's standards, carbon steel is a very poor magnet material. It is easily demagnetized and has a very low energy product of much less than I MGOe (Million-Gauss-Oerstads). This was state-of-the-art technology for almost 300 years until chromium was added to magnet feedstock, which resulted in a three-fold increase in the energy product. The well documented addition of cobalt to permanent magnets in 1917 initiated the 30-year era of "Alnico" magnets that at the time provided a superior magnetic energy product. Since then, the science of magnetism has advanced rapidly and is now considered a highly developed branch of physics and material science. Permanent magnets have had an extremely long history. Figure 1 presents a chronology of permanent magnets that illustrates the increase in energy product. Amazing developments in material science have taken place in the last two decades. The gradual advancement of permanent magnet technology was shattered in 1967 with the initial development of samarium-cobalt (rare earth) magnets. Since that time, the advent of neodymium-boron-iron magnets provided such an increase in energy product that new design concepts were considered. New avenues of study were introduced by the complexities in the material science and physics involved in describing these new permanent magnets. Furthermore, applications for permanent magnets that were previously not considered were now viable. Rare earth elements Rare earth elements have claimed the attention of scientists for the past century. These elements were originally termed "rare" because they were thought to be quite scarce. Since then, however, geological studies have shown them to be relatively abundant. The discovery and identification of rare earth elements is complicated by the inherent difficulties in separating them from each other. The rare earth elements comprise the fifteen transition elements of Group IIIB, Period 6, of the periodic table. These elements extend from lanthanum to lutetium and are commonly called the lanthanide series. Samarium and neodymium are the two most common elements used in the commercial manufacture of rare earth permanent magnets. Commercial grade rare earth magnets There are only a few common types of rare earth magnets that are considered in the circuit design for magnetic separators. Early rare earth magnets of commercial significance (introduced in 1970) consisted of the first generation of sintered SmCo5. The energy product of these magnets ranged up to 23 MGOe, which provided the initial impetus to the field of high-energy permanent magnets. Although these magnets did not produce the extremely high magnetic field strengths of current rare earth magnets, they were relatively temperature stable. Containing 66% Co, they are the most expensive of the basic commercial rare earth permanent magnets. Their use is limited today because they are being replaced by second and third generation rare earth permanent magnets.

Jan 1, 1995

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By A. L. Coello Velázquez

The subject of this paper is particle population balance models (PBM) that describe mineral impact crushing behavior; it is mainly concerned with the selection and fragmentation distribution function due to their importance in this context. The data obtained by Datta (1999) by applying impact pendulum testing to single limestone particles, used by Austin (2002, 2004a and 2004b) to obtain the principal parity of fragmentation functions, were processed in order to compare them with the results of other authors, such as Nikolov (2002 and 2004) and Vogel and Peukert (2003 and 2005) so as to increase knowledge of impact crushing. From this data it has been possible to obtain the performance models of the principal parameters of fragmentation function, thereby reducing the number of experiments necessary to model the impact crushing process. The authors also propose a simplification of the selection function model posited by Austin (2002).

Jan 1, 2011

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By C. M. Goodall

Solids and liquid phase residence time distribution data is reported for a laboratory column flotation cell. The effects of various physical flotation parameters on residence time distributions are reported and analyzed. A plug flow model with recycle is proposed for the froth phase and a tanks in series model for the pulp. By comparison of two and three phase residence time -distribution data it has been shown that the use of liquid residence time distribution data to predict the residence time distribution of the solids in a column is not valid.

Jan 1, 1990

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

By D. Akers

Many of the trace elements found in coal are associated with mineral matter, making it possible to remove them by physical coal cleaning. As part of work funded by the Electric Power Research Institute, both conventional and advanced coal cleaning processes were found to provide large reductions in the concentration of many trace elements that, if released into the atmosphere, are considered to be potentially toxic or environmentally harmful. Advanced physical cleaning technologies appear to provide greater reductions than conventional technologies. Chemical cleaning processes may also remove many trace elements, possibly including organically-bound elements such as beryllium. Care must be taken in the disposal of coal cleaning plant refuse because oxidation and leaching of this material can create highly acidic leachate and many trace elements are mobile in an acid environment. Laboratory leaching procedures are potentially useful in determining the degree of risk of water contamination by trace elements should an acid environment form.

Jan 1, 1992