Search Documents

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Raymond Sandiford, Kenneth Xu, Taehyun Moon

Tunnel approach structures situated in slow moving earth flows are subjected to significant earth pressures. The authors have developed a system, utilizing collapsible concrete columns, that limits such loading. The system uses an array of collapsible concrete columns in front of the structure to absorb downslope movement and limit-imposed loads. This concept has been modelled using 3D FEM analyses and a rudimental lab test. For implementation, the collapsible columns would be prefabricated in strengths to mimic the soil strength profile. This concept has merit, and analytical results demonstrate that collapsible columns are a viable means to limit loading.

Jun 23, 2024

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By V. T. McLemore

NMBGMR has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills, geochemistry, photographs, and bibliography. The available data includes location, production, reserves, geologic, geochemical, resource potential, and other data. The NURE stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during 1970s. The NURE hydrogeochemical data provides analyses for water samples. ArcMap includes location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production, and possible environmental concerns, such as physical hazards (i.e. hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point-sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By B. J. Arnold

Prior laboratory work has demonstrated -that much of the fine ash-forming minerals entering a flotation froth are there as a result of water carry-over from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 300 cu ft WEMCO flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent of solids in the froth). Reagent changes which result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1990

By William Gleason

"While the American Exploration & Mining Association (AEMA) was preparing to close one chapter and begin another during its annual conference in Spokane, WA Dec. 3-7, word of a significant victory on an issue that has been important to the association for many years came from the halls of Washington, D.C.During a keynote address on Dec. 6, Joe Balash, assistant secretary of Land and Minerals Management for the U.S. Department of the Interior (DOI), told a sold-out lunch crowd that the DOI had released final drafts of proposed revisions to the Obama-era greater sage grouse conservation plans. The revisions suggest removing hundreds of thousands of acres of federally protected habitat in Utah, and easing restrictions on energy development and other activities, including mining, in Colorado, Idaho and Wyoming.The protections of the sage grouse were put in place by the Obama administration in 2015. The sage grouse, a prairie fowl, is considered by conservationists to be a key indicator species for the health of America’s sagebrush ecosystem. The previous plan to protect the ground-dwelling bird imposed restrictions to development in sage grouse habitat, but did not place the birds on the endangered species list — a move that many believed would have imposed far more rigid rules.AEMA, and its executive director Laura Skaer, led the way in the fight against the Obama-era greater sage grouse plan, arguing that the plan unnecessarily hurt economic development.“We were the first organization to point out that the greater sage grouse was being used to stop mining, oil and gas production and grazing on public lands in the interior mountain west,” said Skaer who is retiring from AEMA with a significant legal win on this front. “Early on, we cautioned that the proposed Land Use Plan Amendments would be worse than a listing (of the sage grouse) under the Endangered Species Act. Very few believed us until they saw the plans with all of the restrictions and the recommendation for a 4-million-ha (10-million-acre) withdrawal from mineral entry. We were the only organization that filed comments on all 88 Land Use Plan Amendments in 11 states covering more than 24.2 million ha (60 million acres).”"

Feb 1, 2019

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By Bahadir Ergener, Angel Maria Tobar Escudero, Sandra Nowosad

Modern mining companies are increasingly turning to integrate digital technologies and circular economy (CE) principles to increase the sustainability of their operations. The so-called “mine of the future” is envisioned as a smart, integrated system where technologies such as automation, artificial intelligence, digital twins, and real-time data analytics work in harmony with human decision-making and environmental responsibility. Already in 2018, McKinsey and Co. identified that the three drivers that would define a technology-enabled change in mining would be technology, including digital, analytics and automation, management systems able to identify the potential and value of the new technologies, and the culture and capabilities of the organisation, leaning to more agile and responsive organisations. From the three drivers, in the last five years most developments have been centred in the first one. Yet despite rapid advances, the adoption of new technologies across the industry today remains uneven and often slower than expected. Furthermore, it has been identified that the problem on the technology uptake often relay on the lack of operational readiness, process incompatibility or misalignment, and resistance to change within the mining operation. At the same time, leading companies like Rio Tinto, BHP, and Anglo American have each launched major digital transformation programs. Rio Tinto, for instance, operates one of the world’s largest autonomous mining fleets and has integrated digital technologies across nearly all its operations (Rio Tinto, 2025). BHP is actively investing in information and communication technology (ICT) development as artificial intelligence, big data analytics and robotics, and has partnered with battery companies to pursue circular economy initiatives. Only in 2024, their ICT spending reached US$ 438.3 million (Global Data, 2024). Anglo American has rolled out its FutureSmart Mining™ framework, explicitly aligning innovation with circularity and sustainability goals (Anglo American, 2025). The accelerating pace of change across leading mining companies along with the uneven adoption in the technology uptake clearly state how digital transformation is no longer just about implementing new tools, instead it requires a fundamental shift in how people, processes, and culture are aligned. Addressing only the technical layer, while neglecting the human and organizational dimensions, leaves transformation efforts fragile and unsustainable. As the industry must act decisively to close this gap, the true test of transformation is today centred in changing behaviours, mindsets, and systems. Even at the listed leading companies, initiatives have encountered cultural and structural resistance that are relatable to the industry in large: siloed departments fail to collaborate, procurement teams focus on upfront costs rather than lifecycle value, and operators are often excluded from early-stage planning, reducing buy-in. In many cases, a lack of communication or failure to link technology to real operational bottlenecks leads to disengagement at the ground level. This friction reveals a broader issue: mining organizations have historically treated technology and culture as separate domains, when in fact they are deeply interdependent. To address this, the authors propose a systems engineering approach focusing on the mining operations as a complex socio-technical system composed of people, processes, and technologies. Systems engineering offers tools and frameworks for mapping interactions, aligning incentives, designing for feedback and adaptation, and integrating change across organizational boundaries. Specifically, besides technical requirements, it demands treating culture not as an afterthought or side-effect, but as a design variable that must be intentionally shaped alongside infrastructure and workflows. This paper explores how this approach can be applied in practice, by analysing a real-world case scenario where resistance to innovation was overcome not by technical capabilities alone, but through alignment of stakeholder incentives, thoughtful communication, and cultural integration. A particular focus is set on the adoption journey of the Powerbit X, a drill bit technology with significant potential for operational and environmental gains.

Feb 22, 2026

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By Changshou Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,175 t (3,500 st) of ore per day with an average gold grade of 12.6 g/t (0.4 opst). The mine has a large horizontal extent of 762 by 152 m (2,500 by 500 ft) and a vertical extent of 6 to 61 m (20 to 200 ft). Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for mining design and operation in the Leeville underground mine. Three methods are used to collect the geotechnical data in the Leeville underground mine: • Core logging. Most geotechnical data are collected by this method, which is based on exploratory drills and estimates parameters for rock quality designation (RQD), fracture frequency (FF), compressive strength and rock mass rate (RMR). • Site investigation. This method collects more detailed geotechnical data and geostructural data from work done in the underground drifts and stopes. Parameters of RQD, FF, compressive strength, RMR, rock tunneling quality index (Q) and geostructural data are estimated. • Data collected from drill holes made for the critical infrastructure facilities. This method provides the best detailed geotechnical information for areas in which the critical infrastructure located. A complete geotechnical database has been constructed using this geotechnical data collection system. The database can be used for the design of ground support, stopes and stope blasts, among other critical applications.

Jan 1, 2010

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969