Search Documents

By C. J. Lewis

Considerable amounts of the world's known reserves of elemental sulfur are found near the surface in areas of volcanic activity both active and inactive. Because such deposits cannot in general-be mined by the well-known Frasch process, and because other methods of recovery have not proven to be economically competitive except in isolated instances, at present these reserves remain relatively undeveloped. However, projections of world sulfur demand indicate that new sources of marketable sulfur will be needed in future years 2/, 19/. For this reason, recovery of elemental sulfur from these near-surface deposits is of continuing interest. Solvent extraction as an approach to recovery of elemental sulfur from open pit-mined ores of these non-Frasch deposits has received considerable attention particularly at the research and development level 3 /, 7/, l l /, 16/, 21/,23/, 29/ This method has been and continues to be attractive because it presents the potential of high sulfur recovery and purity of product coupled with a relatively simple process flowsheet in which low energy requirements and reasonable operating costs are thought to be possible. However, the physical and chemical characteristics of the native-sulfur ores, of elemental sulfur, and of the known solvents, have presented difficulties in the development of solvent extraction processes. Up to the present time, viable processes have not been realized within the framework of sulfur marketing conditions.

Jan 1, 1970

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By J. T. Clancey

The potential inadequacy of natural gas reserves to supply projected requirements in the 1980's has been pointed out.(1,2) As a result, interest has arisen in the development of new, potentially low-cost processes for the conversion of coal into high BTU gas. In June, 1964, the office of Coal Research (U. S. Department of interior) and Consolidation Coal Company (now a subsidiary of Continental Oil Company) entered into a contract to continue work on coal gasification utilizing the Consol CO2 Acceptor Process. Work under this contract has been specifically directed toward the use of lignite as the carbonaceous feed, although the process is also applicable to non-caking subbituminous coals. The primary objective of this work was to establish the technical feasibility in continuous bench-scale equipment, of the novel features of the C02 Acceptor Process. Secondary objectives were the testing of commercially obtainable acceptors and the design and economic evaluation of a commercial facility. The bench-scale process development has been completed successfully and the construction of a large pilot plant at Rapid City, South Dakota, has been authorized. It is the purpose of this paper to review the technology of this new gasification process and to present the current projected economics of a plant producing 250 MM SCFD of pipeline quality gas.

Jan 1, 1969

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By David A. Zegeer

Since 1980, more than 40 miners have lost their lives by being trapped and suffocating in stock-piles, bins, silos, and similar facilities. Mine Safety and Health Administration (MSHA) is concerned about these accidents, most of which could be prevented if management and miners appreciated the hazard. In February 1986, the coal industry had a suffocation accident that drew national attention. A group of engineers were standing on a coal stockpile. It gave way under their feet. Five of the engineers were buried in the coal and suffocated. As with all fatal accidents, MSHA investigated the cause of this tragedy. I also asked my staff to look into the history of similar accidents. I found out it is rare to have multiple fatalities due to suffocation in material. But, over the years, there has been a long series of individual fatalities from this type of accident. Here are some examples. In Oct. 1985, a coal mine employee in Virginia entered a hopper to collect a coal sample. The feeders were started while he was standing in the hopper. He sank into the coal and suffocated. In Sept. 1985, an employee at a Texas sand company climbed onto a surge pile, to check a problem with sand flow. When other employees found him, the sand had swallowed him. Only his face and one hand were showing. Though the victim's face was clear of the sand, he suffocated before rescuers could free him. Many people do not realize you can suffocate in this kind of situation, though your head is free. Every time you exhale, the material has room to shift and press harder against your chest. Then you have less room to inhale. If this goes on long enough, it gets to the point where you cannot inhale at all. That is what happened to the victim in this accident. In May 1985, a plant operator at a Wisconsin sand and gravel operation purposely slid into the drawhole of a surge pile. He tried to break up large rocks that were clogging the drawpoint. Material piled on the side of the surge pile slid down and buried him. The operator was wearing a safety belt and line. But he was covered by 3 to 3.7 m (10 to 12 ft) of material and could not be pulled free. This incident illustrates another point. A safety line can help. But it is not enough. Workers should never put themselves in a position where loose material can fall on them from above. In Jan. 1985, a young Utah coal miner was waiting for a ride home from a co-worker whose job was at the tipple. A jam developed in the coal bin. The men could not clear the jam from the outside. So the young miner jumped into the bin. He started digging with a shovel at the toe of the coal pile. It caved in on him and he suffocated. The young miner had only three months of mining experience. He had not been trained for work around the coal bin. Since 1980, 16 coal miners and 26 nonmetal miners have lost their lives in loose-material suffocation accidents. Suffocation accidents occur in many areas around mines - bins, hoppers, stockpiles, surge piles, and silos, among others. One recent accident occurred at a surface coal mine in Illinois. The victim was walking over an area that had been drilled and blasted the week before. He fell into a void that had been crusted over with earth. He too suffocated. And many materials have been involved in suffocation accidentscoal, crushed stone, sand, salt, different kinds of ore, ammonium nitrate pellets used in blasting, and a powdery byproduct of iron ore milling called calcine. In addition to fatal accidents, there are near misses. We do not know how many. Most of them are not reported. A person who gets trapped in material, but is rescued, is usually unhurt. MSHA sometimes hears about these accidents by chance, or because they are reported in the local media. We do know that near misses are happening far more often

Jan 1, 1987

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By A. J. MacKellar

The economic viability of any project is generally assessed on an evaluation of the total capital constructed costs along with operating costs, owner's costs and market conditions. This paper will be directed to the role that Cost Engineering plays in the development of the capital costs and the cost control techniques applied thereto.

Jan 1, 1975

By Robert D. Schmidt

The Cyprus Casa Grande Corporation has provided Bureau of Mines researchers with an opportunity to investigate the hydrology of leaching an in place copper ore deposit. Hydrologic investigations of underground in situ copper leaching are being jointly conducted under a cooperative agreement. The hydrologic concerns of leaching operations at the Casa Grande mine focus on maintaining adequate solution injection and recovery rates, and on distributing the injected leach solution effectively within the ore deposit. Hydrologic considerations underlying these concerns relate to the permeability of the oxide ore zone during leaching, the unsaturated condition of the deposit prior to leaching, and the constraints imposed on in situ hydrologic design by the underground mine setting. The investigation involves monitoring of flow and pressure conditions in 58 injection and recovery wells, estimating permeability conditions using a hydrologic model, and on-site testing of hydrodilation and airlift pumping. Transient, fracture-controlled permeability is determined to be the dominant hydrologic consideration. A statistical modeling procedure has been developed for estimating changes in permeability during leaching. Flexibility in well design and operation is essential for accommodating the changes in fracture permeability that occur during leaching.

Jan 1, 1990

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By M. Manrique

Various pyrometallurgical methods for treating Ilmenite and Zircon concentrates are reviewed. Laboratory experiments, using a thermal plasma reactor, have been performed to evaluate: the conversion of ilmenite to TiC or TiC-Fe and the conversion of zircon to ZrC or ZrC-SiC. Results are examined and possible processing routes are identified.

Jan 1, 1996

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014