Search Documents

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By Josh Savit

Corporate responsibility already encompasses safety and compliance. No longer will companies be able to use differing standards of care to miners based on the country in which they are working. This is not only an issue of social license, but one of global risk management.

By Taeyong Lee, Cole Bales, Matt Fowler, John Horne

Mitchell Point Tunnel near Hood River, Oregon is one of the more unique segments of the Historic Columbia River Highway and State Trail being constructed through the Columbia River Gorge. This 650-foot bike/pedestrian tunnel set to open in 2024 is being delivered by FHWA in partnership with Oregon DOT, Oregon State Parks, and the U.S. Forest Service. Primarily driven using drill & blast excavation methods through basalt, the shotcrete and dowel-supported tunnel features masonry portals and ve window adits that provide illumination and views of the river similar to the original highway tunnel of many vistas built in 1915 that was removed in 1966 to make way for Interstate 84. This paper summarizes the planning, design, and construction.

Jun 23, 2024

By T. M. “Mike” Gurr

"U. S. marketable phosphate rock production for the 2018 crop year (July 1, 2017 to June 30, 2018) showed an increase to 27.7 Mt (30.5 million st) from the 2017 crop year production of 27.1 Mt (29.8 million st), as reported to the U. S. Department of the Interior by the mining companies operating in the United States during crop year 2018 (Table 1). Domestic consumption decreased in the 2018 crop year to 23.9 Mt (26.3 million st), as compared to the 27.2 Mt (30 million st) consumed in crop year 2017. U.S. imports of phosphate rock increased to 3 Mt (3.3 million st) for the 2018 crop year from the 1.81 Mt (1.9 million st) for crop year 2017. Imports of phosphate rock were from Peru and Morocco. There was an increase of 2.85 Mt (3.1 million st) in producers’ stocks from 7.45 Mt (8.2 million st) in crop year 2017 to 10.3 Mt (11.3 million st) in crop year 2018 (Table I).For calendar year 2018, Florida and North Carolina phosphate rock production accounted for 75 percent of the total U.S. production, with the balance being produced in Idaho and Utah. The Florida and North Carolina percent of U.S. production is declining. U.S. production of 25.7 Mt (28.3 million st) in calendar year 2018 was produced by five companies at 10 mines in four states and accounted for approximately 9.6 percent of the world production of 267.7 Mt (295 million st) for calendar year 2018 (Table 2).In calendar year 2018, U.S. phosphate production decreased by 2.2 Mt (2.4 million st), while companies increased stocks of phosphate rock by 1.7 Mt (1.9 million st). The domestic production for calendar year 2018 of 25.7 Mt (28.3 million st) represents 78.4 percent of the domestic production capacity of 32.8 Mt (36.1 million st).At present, China reportedly produces more than 50 percent of the world’s phosphate rock. As a result of planned expansions, Morocco production has increased from 27 Mt (30 million st) in 2017 to 33 Mt/a (36 million stpy), which is approximately 12.3 percent of the world’s production, moving ahead of the U.S. production. In calendar year 2018, the U.S. phosphate rock production was 25.7 Mt (28.3 million st), which is less than 10 percent of the world’s production of phosphate rock (Fig. 1)."

Aug 1, 2019

By Daniel McNamee, Wern-ping N. Chen

The Amtrak East River Tunnels include four tunnels, Line 1 to Line 4, which extend from New York Penn Station in Manhattan, under the East River to Sunnyside Yard in Long Island City. Since fall 2015, Amtrak has initiated a program to repair and reconstruct the century-old tunnels, including structural repairs of all the tunnels and reconstruction of the Line 1 and Line 2 tunnels. The reconstruction includes bench wall demolition and replacing and installing the following elements in the tunnels: direct fixation track, traction power, signal, communication, and tunnel fire/life/safety components. This paper provides design and site investigation challenges and knowledge gained from this program.

Dec 1, 2022

By Rob Herr, Irwan Halim, Heather Marsh

This project will expand sanitary sewer within the City of Columbus. It consists of 2.5 mile long, 72-inch finished diameter pipe grouted inside 10.8-foot diameter tunnel excavation in shale. This paper describes the multi-faceted geotechnical exploration to minimize the underground risks. The tunnel will cross below a buried valley with minimum cover of highly weathered rock. The risk mitigation to cross the valley includes contingencies and cost allowances. Provisions to prevent impact on adjacent groundwater resources will be described. Latest construction updates will be provided including contractor alternate shaft support and pre-excavation probing to mitigate tunneling risk below the valley.

Jun 23, 2024

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By U. K. Custred

Who We Are Farmland Hydro (FHLP) is a Limited Partnership formed by Farmland Industries, the largest U.S. farmers’ cooperative, located in Kansas City, MO, and Norsk Hydro, a large Norwegian company engaged in fertilizer, petroleum and the specialty metals industry. Both of our parent companies have a long history of commitment to the fertilizer industry. This year, Farmland Industry celebrates its 71st year in the business, and Norsk Hydro celebrates its 100th operating year! We employ approximately 300 associates in Central Florida. What We Do Farmland has been active in Hardee County, FL since the 1970’s as a large landowner and citrus grower. We plan to expand this activity into phosphate rock mining. The phosphate rock produced here will be shipped to our nearby chemical fertilizer complex in Polk County, where we produce quality phosphate products - liquid and granular fertilizers. Of the phosphate rock mined, 90% is used to make fertilizer. Other uses include animal feed, vitamins, medicine, light bulbs, soft drinks, film, flame resistant fabric, optical glass, toothpaste, bone china and other consumer products.

Jan 1, 2000

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Ken Goering

"Bridgestone Americas opened the company’s first U.S.-based giant off-road radial (ORR) tire plant in November. The 139,000-m2 (1.5 -million-sq ft) plant, located on a 222-ha (550- acre) site in Aiken County, SC, will produce radial tire products, including 157-cm (63-in.) tires, used on mining and aggregate haul trucks.The plant, announced in 2011 as a $970-million investment, represents the largest investment that Bridgestone has made in the United States, and is also the single largest investment ever made in South Carolina. Although it had already been producing tires for a few months, the plant officially opened with a ceremony in November 2014, attended by South Carolina federal, state and local elected officials, as well as Bridgestone personnel from the United States and Japan. Prior to the Aiken County plant’s construction, all of Bridgestone’s giant ORR tires were manufactured at its Shimonoseki and Kitakyushu facilities in Japan.Kurt Danielson, president of Bridgestone’s U.S. & Canada Commercial Group, said the facility was built to primarily serve the North American mining and aggregate industries in a more efficient manner. "It’s a real change for us," he said of the U.S.-based plant at its opening ceremony. "This allows us to have a true global presence."The Aiken County plant is intended to allow Bridgestone to meet customer demand for ORR tires, Danielson said. "It really frees up our other plants in Japan to service the rest of the world, allowing us to serve our customers faster," Danielson said. "As soon as we build (a tire), we can have it to our customers."Tires manufactured at Bridgestone’s Japanese plants could spend up to a month in transit to the American continents; from initial mixing of the rubber and other compounds to being warehoused, tires manufactured at the Aiken County plant can be ready to ship in four to five days.Danielson said most of the tires built in Aiken County will be used by customers on the American continents. "We will export," he said, "but our desire is to use as much capacity as we can for the Americas."Ground was broken for the facility inSeptember 2011, when commodity prices were much different than today and global demand for tires had skyrocketed."

Jan 1, 2014

By W. H. Jang

Although surface chemistry fundamentals of semi-soluble minerals have been studied by many researchers, detailed understanding of these systems is still incomplete. In-situ FT-IR/IRS techniques have recently been used to successfully describe the adsorption of carboxylates at semi-soluble mineral surfaces. However, the wetting characteristics of these adsorbed films require further consideration. In this regard, the hydrophobicity and stability of transferred Langmuir-Blodgett (LB) monolayers of fatty acids at fluorite and calcite surfaces has been studied by contact angle measurements with polar and apolar liquids. Generally, it was found that the transferred LB monolayers of fatty acids at a calcite surface are unstable whereas such monolayers transferred at a fluorite surface are stable, as revealed from advancing and receding contact angle measurements. These results are believed to be due to the incomplete reaction of fatty acid monolayer at the calcite surface. In addition it was found that a closely packed well-ordered stearate monolayer with good hydrophobicity, equivalent to that of a transferred LB monolayer, can be formed at fluorite surfaces by spontaneous adsorption and self-assembly from aqueous solutions.

Jan 1, 1995

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996