Search Documents

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By A. Bhattacherjee

Industries in general and the mining industry in particular have become more safe than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction through job design, work procedures, and worker training. Mine accident and hazard control has to be practiced in a manner which is consistent with the overall objectives of the mine management, among which are the optimum allocation and effective utilization of the resources. The purposes of this paper are to (i) review the role risk analysis in safety management with references from mining and other industries; (ii) discuss the risk measures appropriate for injury analysis; (iii) present a set of analytical tools to injury experience data in under-ground coal mines; (i v) apply these tools on case study example; (v) discuss the results of the case study; and (vi) amplify the application limitations and the future research needs.

Jan 1, 1991

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By T. Pool

Introduction After two decades of contraction and consolidation, the uranium industry has seen a recent major expansion. Rapidly increasing uranium prices and the ability to raise speculative capital in share markets worldwide have brought over 300 new participant companies into the uranium industry: “juniors” as they are known. These companies participated in a global land rush for known deposits as well as for prospective land positions in order to secure a “piece of the action” for their respective portfolios. Mostly publicly-traded companies, these “juniors” have captured the attention of world’s investing public with spectacular gains; as much as 1,000s of percent in less than four years. The initial phase is over, however, and these companies must now prove that they can be successful in exploration or production.

Jan 1, 2007

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

And a new generation of safety culture experts are telling mining companies how to use it: It is a situation that is still too common in the mining industry: the latest personal protective gear is in place. The safety rules are known and followed. And then, in a moment of inattention or carelessness, a mistake is made and someone gets hurt or killed. Common wisdom claims that such accidents are impossible to eliminate entirely. Mining is dangerous, and some miners will always be hurt and killed. An increasing number of mine safety experts, however, reject the common wisdom. A year with zero mining deaths is possible, they say; with the use of one of the newest weapons to the mining industry in the safety war: the concept of safety culture. Safety culture refers to the set of attitudes, beliefs, perceptions and values that influence safety in the work environment. It is also sometimes called the way an organization behaves when no one is watching. Robert Peters, of the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH), describes safety culture this way: ?It?s what?s believed on a day-to-day basis. For example, if a miner sees a workplace hazard and he truly believes that his boss wants him to identify the hazard and bring it to the company?s attention, that would be an example of a positive safety culture.?

Jun 1, 2010

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Richard A. Thomas, Connor B. Brown, Thomas H. Dubaniewicz, Teresa Barone

Electric vehicles powered by lithium-ion (Li-ion) batteries are being developed by mining vehicle manufacturers as a replacement for diesel-powered vehicles. Explosion-proof (XP) enclosures are frequently employed to enclose electrical ignition sources in gaseous underground mines to prevent the spread of an internal methane-air explosion to a nearby explosive atmosphere. Due to thermal runaway (TR), Li-ion batteries have the potential to cause pressurized explosions in an enclosed structure. Past research has shown the potential for well-confined Li-ion cell TR to drive pressures beyond the conventional pressure specification for XP enclosures. Researchers at the National Institute for Occupational Safety and Health (NIOSH) used an Accelerating Rate Calorimeter (ARC) to induce thermal runaway of Lithium Titanate or Lithium Titanium Oxide (LTO) type 18650 cells enclosed within containers with various volumes and found an inverse power relationship between the TR pressure and available free space. The results were similar in magnitude to that of lithium iron phosphate (LFP) cells, which were used in prior testing. Temperatures, gas amounts, and TR pressure-rise rates were also recorded. The data indicate that with enough free space, the pressures can be lowered below the conventional pressure specification for XP enclosures.

Feb 1, 2024

By Nikhil Dhawan, SHAILA MIR

The emerging problem of electronic waste has promoted the interest in exploring metal recovery from secondary sources under the umbrella of urban mining. This study presents the physical and chemical characterization of various components present in end-of-life laptops to help ascertain the sites of metallic values and develop sustainable and environment-friendly recycling. The recycling potential of a laptop is evaluated by sequential disassembly, separation, and characterization of components such as body (49.8 wt.%), printed circuit board (9.7 wt.%), hard disk drive (4.9 wt.%), and battery (12.4 wt.%). The printed circuit boards comprise metallic values, majorly copper (25 wt.%), tin (5.8 wt.%), and lead (3.1 wt.%). The precious metals (Au, Ag) with an economic advantage are abundantly present in electronic components such as integrated circuits, capacitors, resistors, and processors. Critical elements such as lithium, cobalt, and rare earth elements are detected in the discarded laptops' batteries and hard disk drives. The recycling potential representing the amount of material that can be recycled in various components, depending on the type, concentration, and purity, is determined in the range of 36–100%. On average, a unit laptop contains~ 386 g of Cu (14.45 wt. %), 49.73 g Co (1.86 wt. %), ~346 mg Ag, ~141.2 mg Au, ~650 mg of rare earth elements (Nd, Dy). This study presents a database for investigating integrated and economical recycling techniques from different components of a laptop, and an overall process flow is also proposed.

Jul 24, 2021

By Tim O’Neil

ISO 9000 is a system of quality standards that originated in Europe in the 1980s and has since been widely adopted by manufacturing companies throughout the world. The ISO 9000 standards have received less attention in the minerals industry. But, in part as a result of customer pressure, a trend is beginning to emerge for minerals producers to seek ISO certification. This is especially true among producers of industrial minerals. In early October 1994, SME's Industrial Minerals Division held a conference "ISO 9000 - uniting industrial mineral producers and consumers into quality partnerships," in Nashville, TN to bring people from the industry together to talk about their experiences with ISO 9000. William J. Miles, of Bentonite Corp. Inc., and A. Frank Alsobrook, of Alsobrook and Co., were cochairmen of the meeting. In his introductory remarks, Miles noted, "ISO 9000 is more than a quality program. It is a quality philosophy. Appropriately imple-mented, it is a contract between the supplier and the customer. It leads to continuous quality improvement and reduced manufacturing costs."

Jan 1, 1995

By E. Stolarski

The circulating fluid bed (CFB) technology can proudly point to its history of more than a quarter of a century of commercial operations. Over 80 CFB units operate in aluminum calcining, coal combustion and gold roasting. This paper describes the invention of the circulating fluid bed and chronicles its development and evolution from calcining through coal combustion to gold roasting. It presents performance data of Lurgi's CFB units in operation and highlights the six gold roasting plants currently operating throughout the world.

Jan 1, 1998

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By Jan Krason

Introduction The South African Witwatersrand is the world's largest gold-bearing province and gold producing district. But the production capacity of the very big mines (Vaal Reef, Driefontein Cons., Western Holdings, Western Deep Levels, and others) is not as large as that of the Soviet Union's Muruntau gold mine. The Muruntau gold-bearing ore body was discovered in 1956-57, and has been in operation since that time. In the early 1970s, this mine produced 70 to 80 t/a (2.3 to 2.6 million oz per year) of gold. Within the last few years it has become the world's largest producing gold mine. Russian authors do not publish ore reserve or rate of production data. But it is very likely that the Muruntau mining complex, which involves several ore bodies, is currently producing about 143 t/a (4.6 million oz per year) of gold. The author has confirmed this by personal information from several knowledgeable Russian geologists. This amounts to one-half of

Jan 11, 1984

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997