Search Documents

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By W. A. Wilkinson

Mining companies today are under increasing pressure to boost output from their existing mines and to bring new projects online quickly. Fundamental to the long-term performance of an operation is geologic modeling and mine planning. To maximize mine profitability, planners and schedulers must account for a staggering array of variables and create accurate mining plans that meet production and profit targets. Not surprisingly, this can be a difficult task, and getting it wrong can result in large unforeseen costs and significant lost revenue opportunities. This paper discusses the top five challenges geologists and engineers are facing in developing mining plans.

Jan 1, 2012

By D. J. Pandelis, W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By B. Swarbrick

Today’s mining occurs in a dynamic world of conflicting objectives. Mining companies have to look further than a traditional cash flow analysis to determine the potential value of developing a mine. In particular, proposals for new mine developments undergo rigorous scrutiny by a variety of stakeholders including regulators, NGO’s, and the local communities. From a business risk perspective, how mining companies address stakeholder concerns can have a dramatic impact on the success of the project. In today’s mining environment mining companies must continue to ‘walk the talk’ to stay in business, particularly during downturns in the business cycle. Falconbridge’s Raglan Mine is an example of a project that was successfully developed in a region that is sensitive from many perspectives, including environmental, socio economic, and regulatory. Close working relationships with local stakeholders along with strong environmental management systems are necessary elements of continued success for the project.

Jan 1, 2000

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

By J. Parker

Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa (4000 and 7000 psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition

Jan 1, 1991

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By Wu Aixiang, Zhou Qian, Zhou Zaibo, Liu Juanhong, Wang Hongjiang

To improve the pumping capacity and engineering efficiency of fresh thickened tailings slurry, a high charge density superplasticizer was developed to improve the rheological properties of tailings slurry. The effects of superplasticizer content, the concentration and fineness of tailings, the proportion and type of cementitious materials, temperature, and hydration time on the rheological properties of unclassified tailings slurry and backfill materials were studied. The variation characteristics of the slurry yield stress, plastic viscosity, and thixotropy with different factors were measured by a Brookfield R/S-SST plus rheometer. The experimental results of fresh thickened tailings illustrated that the higher the concentration of the slurry and the finer the tailings, the worse the rheological properties of the slurry. The results of cemented paste backfill materials indicated that the rheological parameters increased as binder content and time increased. The rheological parameters decreased as the temperature increased. The addition of a superplasticizer reduced the rheological parameters and improved the rheological behavior of the fresh thickened tailings and cemented paste backfill materials, which was beneficial to the slurry’s pipeline transportation. This paper can provide technical guidance for slurry transportation in the backfill system and provide a reference for designing the superplasticizer used in tailings.

Jan 5, 2022

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By J. R. Shultz, R. J. Lambert

One of the present trends in the mining industry is the increased use of mining contractors. In the past, many project owners have utilized mining contractors for topsoil stripping or overburden removal, usually on a short-term or periodic basis. In recent years, mining contractors have not only removed the overburden, but mined the product as well. Why is this change occurring? A prevalent trend in the mining industry appears to be the outsourcing of non-core and non-strategic functions, allowing producers to focus more on areas of technical expertise where higher incremental value is added—that is the processing, refining, and marketing of the product. As capital allocation becomes more critical, this trend is likely to continue.

Jan 1, 2002

By Brenda Myers-Bohlke, Tor L. Brekke

INTRODUCTION In recent years several cities in the Eastern United States have constructed subway systems in deeply weathered igneous and metamorphic rocks. Portions of these transit tunnels and shafts have penetrated zones of saprolite. The purpose of this paper is to define saprolite and discuss saprolite behavior in terms of construction and design of tunnels and shafts. Saprolites are products of in situ weathering of rock, with properties intermediate between those of soil and rock. A well-developed weathering profile can be divided into zones of residual soil, saprolite, transition zone materials, weathered rock, and fresh rock. Saprolites are distinguished by a high degree of weathering and by retention of parent rock textures and discontinuities. These structures persist as relict features because of iso-volumetric weathering (Cleaves, 1974) and formation of intergranular bonds that give cohesion to the saprolitic material. As saprolite continues to weather, the bonds are broken, causing the saprolite to decompose and disintegrate into a true residual soil mass without relict structure. Saprolites may form from igneous, metamorphic or sedimentary rocks, but are most easily recognized when derived from igneous and metamorphic rocks because of their inherent structures. The physical characteristics and properties of residual material vary as a function of mineralogic composition, structure, and discontinuities of its parent rock.

Jan 1, 1985

By K. Vatterrodt

Thallium is not significantly removed from mining influenced water (MIW) through conventional treatment in hydroxide precipitation plants. We experimentally investigated modifications to hydroxide precipitation schemes to concurrently remove thallium. Our goal was to determine cost effective and efficient hydroxide precipitation process modifications for thallium removal. Strategies for removal targeted multiple mechanisms including sorption, co-precipitation and/or oxidation of monovalent thallium. Modifications were tested in batch and included oxidant evaluation and the role of manganese. Removal of thallium was enhanced by the addition of permanganate as well as oxygen by aeration. In addition, contact with retained solids and the initial manganese concentration played an important role in the extent of thallium removal observed. This paper reports on our findings and discusses the implications in the removal of thallium with minor modifications to the hydroxide precipitation process.

Feb 27, 2013

By Neel Gupta, Dustin M. Crandall, Brijes Mishra

X-ray computed tomography (CT) images of rock specimens often contain artifacts which must be corrected before scientific analyses are performed. This paper presents a new workflow of automated image processing to utilize poor-quality X-ray CT scan images. The workflow runs on the open-source image analysis software and efficiently separates desired features from low-contrast scanned images. The new workflow is a two-step technique using contrast enhancement and automated feature segmentation to generate noise-free binary images. The results of binary images using the proposed workflow and using a conventional thresholding technique are analyzed to show the quality of the proposed method. The paper also presents a workflow of estimating the structural geometries of features in two and three dimensions. The results of the structural feature analyses and computational time were compared between the open-source (ImageJ) and commercial image analysis software (Bruker Computed Tomography Analyzer). The commercial software was more computationally efficient, but the task-specific macros in open-source software enabled the user-desired automation in image processing and data extraction of desired structural features of comparable quality.

Sep 8, 2022

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By Randall J. Essex

The Construction Institute of the American Society of Civil Engineers recently published the second edition of a 1997 publication on geotechnical baseline reports. The new publication, called Geotechnical Baseline Reports for Construction, Suggested Guidelines, represents a 2-year effort that adds three new chapters to the original publication, as well as capturing practitioner commentary through two industry workshop sessions. The paper will overview the contents of the new publication, particularly the three new chapters.

Jan 1, 2008

By Teena Redhorse, David Tsztoo, Anthony Yu

"Since ancient times, storing and conveying water via underground water systems and tunnels has been touted for its strategic advantages. Underground cisterns and tunnels assured protection of essential fresh water supplies from man made contamination and especially from enemies who would gain an advantage by disrupting an adversary’s water supply in a siege. Modern day engineers do not usually specify tunnels for reasons of avoiding deliberate contamination or siege — however, they are just as enamored with the idea of building tunnels for water conveyances.Such was the case for the San Francisco Public Utilities Commission (SFPUC). The SFPUC provides drinking water to 2.6 million residential, commercial and industrial customers in the San Francisco Bay Area. The SFPUC’s water system includes 257 km (160 miles) of transmission pipelines and tunnels from the SFPUC’s largest reservoir, the Hetch Hetchy Reservoir inside Yosemite National Park, to San Francisco. About 129 km (80 miles) of the system consist of tunnels. A 30-km (19-mile) section of the tunnel network, called the Mountain Tunnel, was thought to be at risk of a catastrophic failure in its concrete-lined section of 18 km (11 miles). For much of the project planning process, a new replacement tunnel was presumed to be required according to the tunnel planners.Originally constructed between 1917 and 1925, the Mountain Tunnel has been in continuous service since 1925. The 30-km (19-mile) tunnel is located downstream of the Hetch Hetchy Reservoir water source in Yosemite National Park, between the Early Intake and Priest Reservoir (Fig. 1). Approximately 18 km (11 miles) of the tunnel is lined with unreinforced concrete. Though the condition of the tunnel was being monitored through water sampling and periodic inspections, there was growing concern that the tunnel lining was at risk of a partial collapse that could interrupt water delivery for up to nine months. The SFPUC was faced with a decision to construct a new bypass tunnel to replace the lined section of the Mountain Tunnel or to rehabilitate the existing tunnel."

Jan 6, 2018

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989