Search Documents

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

Jan 1, 2006

By Wilfred P. Schmoe

Introduction An integrated oil company has two options in approaching strategic planning. It has to decide whether it is in business for the long-term. I state this in all seriousness. Those who help manage public companies have the responsibility of good stewardship of other people's money. We must decide whether continued investment in our basic business will generate a reasonable rate of return. With a world surplus of petroleum production capacity, and continuing downward pressure on prices, this question should be addressed by all oil companies. And a positive answer is not necessarily a foregone conclusion in all cases. The decision should be made based on proven competence in finding and developing petroleum reserves on a cost-competitive basis with other producers, and on a frank analysis of future prospects. This should include a realistic assessment of the projected rate of return on specific investment projects. If a company did not pass these tests, its strategy could take one of four paths. Diversification First, it could diversify. But recent history suggests that oil companies are not good at managing other businesses. Second, it could seek a buyer for its business at the optimum return for its owners. Third, it could sell its assets on a piecemeal basis. And, fourth, it could adopt a longer-range plan of self-liquidation by living off current recoverable reserves. In other words, by not investing in exploration and development, it could maximize short-term profit and pass the money back to shareholders in the form of dividends. The Conoco component of DuPont has a below-average cost of finding petroleum, a good track record of efficient production, and a full plate of projects that pass the test of return-on-investment. In short, Conoco is in business for the long-term. That fact, in itself, determines at least one key element in strategy. This is to extend the life of the petroleum reserve base while at the same time maintaining maximum efficient rates of production to provide a strong cash flow. A company that is able to maintain a strong reserve base will ultimately see the value of those reserves escalate as world oil supplies tighten. Our planners expect this tightening to occur within the next decade as demand grows and production in non-OPEC areas of the world begins to decline. An exploration program tailored to meet the requirements of reserve replacement and current production should have two basic parts. The first is relatively low-risk exploration in proven oil provinces. This is augmented by

Jan 6, 1985

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By A. Steinmüller

Introduction In the design and operation of gravity concentration circuits, the application of process models for spiral concentrators offers significant benefits. A substantial amount of work has been produced over the last 30 years in the field of modeling the metallurgical performance of spiral concentrators. It is not the aim of this contribution to add to the refinement of modeling technique but to share some of the experiences and potential improvements which can be achieved in a relatively simple way. The design of spiral circuits usually requires extensive testing. This is often conducted in batch operation only, either due to lack of suitable continuous testing facilities, the unavailability of sufficient quantities of sample, or other constraints. Typical problems arising during circuit development from batch testwork are the extrapolation of results to different feed conditions, and resolving of internal recycles. Model selection and development The classic approaches in spiral modeling technique range from fundamental fluid dynamics, based on the Navier-Stokes equations in combination with expressions for local slurry properties, to fully empirical and statistical models. With the initial objective of developing an in-house tool for gravity circuit optimization and development, mathematical model types from each category, available either commercially or in the published literature, were evaluated. Model selection For the desired purpose, an approach proposed by Holland-Batt (1990) was found suitable, which was adopted and modified. Holland-Batt reported that the shape of release curves in spiral applications could be described by a combination of a linear function in the initial recovery zone, and a power law function outside this zone. The proposed recovery function was formulated as

Jan 1, 2005

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By B. K. Belle

The use of diesel engine locomotives in South African mines can be traced to Van Dyk Consolidated Mines Ltd on the Witwatersrand gold mines in 1928 as a replacement for battery locomotives. The advantages and disadvantages were recognized in those days, and surprisingly, there are no significant additions to this list, but only refinements. In the absence of any Occupational Exposure Limit (OEL) for Diesel Particulate Matter (DPM) in SA, the Mine Safety and Health Administration (USA) rule is currently being used as a benchmark for the ventilation engineering designs. This paper discusses the ongoing SA journey of measurement and limitations of exposure data for ventilation planning and regulatory purposes. The currently accepted DPM limits are based upon the belief that they are economically and technically feasible for the mines to reach and are not necessarily health based. For SA underground platinum mines, a median TC/EC ratio of 1.8 with a range of 1.2 to 5.8 was observed. For SA coal mines, a median TC/EC ratio of 1.44 with a range of 1.25 to 2.13 was observed. While it is common practice in the USA to use the ratio of TC/EC for metal mines to be 1.3, the ratio found in local platinum mines is 2.2 and for coal mines, the ratio was 1.53 which is lower than Australian studies, i.e., 1.96. It has been shown that a need for critical analysis of TC/EC ratios exists, and possible reasons for variance must be understood before stringent adoption of overseas recommended limits for DPM. It is hoped that the findings from this paper would provide input to scientific approaches in developing appropriate conversion factors, limits for DPM and also in ensuring appropriate error factors (currently 1.14 for TC and 1.2 for EC) for compliance determination.

Jan 1, 2009

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

By I. S. Parrish

This article offers one of the infrequent looks at Chinese mining. It includes a brief review by Parrish of a tungsten symposium held there and his comments on and impressions of the mines he visited. In early Oct. 1981, a Symposium on the Geology of Tungsten was held in the Peoples Republic of China. There were approximately 100 participants. Half of them were Chinese. The remainder included representatives of the United Nations, geologists from other nations in Southeast Asia, and 10 invited specialists from other countries. The invited guests included K.F.G. Hosking of the Camborne School of Mines, United Kingdom; C.S. Hutchinson of the University of Malaysia; K. Mattson of LKAB Int. AB, Sweden; T. Kwak of Latrobe University, Australia; K. Sato and S. Ishihara of the Geological Survey of Japan; M. Clarke of the Department of Mineral Resources, Indonesia; P. Bateman of the US Geological Survey; and the author. R. Horsnail of Amax was also invited but was unable to attend because of delayed visa clearance. The meeting was noteworthy because the Chinese were presenting more than half the papers. In addition, following the formal session, everyone was taken to the famed Jiangxi tungsten district and toured four mines there. Organization and Background The idea for a symposium on tungsten geology was brought up in late 1979 during a visit to China by the Economic and Social Commission for Asia and the Pacific (ESCAP) and, in particular, by members of the Regional Mineral Resources Development Centre (RMRDC) of the United Nations. Discussions continued and in the spring of 1981 invitations were sent to selected geologists throughout the world. China's Ministry of Geology handled arrangements, scheduling, and logistics. Travel to China and all correspondence before the symposium were coordinated by the Bandung, Indonesia Bureau of RMRDC. All costs in China were met by the Peoples Republic of China. Airfares and "per diem" enroute for participants were paid by respective governments, sponsors, or individuals. On Oct. 10, visiting participants entered China from Hong Kong. The author and a few others traveled by train to Guangzhou (Canton). Most of the group flew in the next day. The entire group was then taken to Nanchang, traveling by sleeper train and arriving on Oct. 11. The symposium group stayed at the Kiangsi Hotel, where the meetings were held. Meetings Oct. 11 was a day of orientation and rest. The group was taken to an art museum and treated to a Chinese opera movie. The formal meetings began on Monday, Oct. 12. Simultaneous translations aided presentations, though more than half the Chinese speakers delivered their talks in English. The acoustics and sound system were excellent, and the Chinese provided 35-mm and overhead projectors. There was no screen, however, and the yellow, painted wall that was used detracted from projection clarity. In general, the Chinese papers were detailed, thoughtful, and professional. Some, naturally, were stronger than others. Taking them as a unit, one derives the following sequence to the Chinese approach to tungsten exploration: (1) Geologic investigations with mapping at a scale of 1:200,000 accompanied by only minor geochemical or geophysical work. (2) Geophysical investigation with regional gravity and magnetic surveys directed toward identifying deep, tectonic systems and seeking granites in thick, crustal environments. (3) Geochemical sampling in-

Jan 6, 1982

One of the most important parameters in mine ventilation planning is the friction factor (K). Accurate values of friction factors are critical especially when carrying out mine ventilation simulations. No computer simulation of a mine ventilation network is meaningful if the airway resistances are not accurately estimated (when planning a new mine) or measured (for an existing mine). However, in the first case not many reliable values of friction factors exist in the international literature. This paper presents the results of a research project carried out in the province of Quebec where ventilation friction factors were measured in all underground metal mines. These friction factors are statistically analyzed and tabulated. A friction factor database was created that also includes the friction factors measured in the past by other people. This database can help the mine engineer to accurately estimate ventilation friction factors according to the specific conditions. This database offers several values of friction factors typical for hard rock mine conditions typical of modern underground metal mines.

Jan 1, 2009

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By Terry M. Tilley, Gregory P. Sherry

Purpose This is a unique project because the mining and tunneling industries have become highly mechanized and cannot normally accommodate a project where surface disturbance must be minimized or eliminated when there is less than 10 feet of ground cover. More traditional less mechanized methods must be employed and the skills and techniques for accomplishing the work have become all but non-existent. Therefore, this article highlights those areas of specialized skills and techniques. Methods The article will describe the design approach, the method(s) of ground support selected, the method(s) of excavation selected, the planning, scheduling and materials selection process. In addition, the article will describe the actual production characteristics and the results of the project. This approach will concentrate on productivities, adaptations to actual conditions and the quality of the end product. The design approach basically was to insure that the temporary support methods were adequate for the excavation and shoring stage of the project. The final concrete liner was designed using conventional structural design methods with the goal of constructing a tunnel that will last 100 years. The methods of support were spiling and variations of spiling in order to provide advance temporary ground support. In this project spiling is steel channel cantilevered and driven into the ground ahead of the working tunnel face which supports the ground allowing the face muck to be removed with overhead protection’. Conclusion This will be a discussion of the applicability of the methods. The actual performance of the excavation and shoring methods will also be evaluated. The final concrete liner completion results, the actual production rates and the conformance with budget and schedule will be addressed.

Jan 1, 2005

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007